Install Anti-Tip Boards; Connect The Water Supply - Jenn-Air Euro-Style JS48SSDUDE Installation Manual

NOTE: Pass the dolly strap under the handles.
2. Place pieces of the shipping carton on the floor when rolling
the dolly and refrigerator into the house. Move the refrigerator
close to the built-in opening.
3. Place top of cardboard carton or plywood under refrigerator.
4. Stand the refrigerator up. First, place the left bottom edge of
the refrigerator on the floor, stand the refrigerator upright and
then lower the right-hand side of the refrigerator to the floor.
5. Reassemble the trim and top grille after the dolly has been
removed from the refrigerator.

Install Anti-Tip Boards

IMPORTANT:
To avoid tipping during use, the solid soffit must be within
■
1" (2.5 cm) maximum above the refrigerator. If the solid soffit
is higher than 1" (2.5 cm) or one is not available, then the
refrigerator must be braced.
It is recommended that board(s) be installed before the
■
refrigerator is installed.
Board(s) must be long enough to fully cover the width of the
■
compressor cover.
Locate the board(s) so the bottom surface(s) of the board(s) is
■
(are) 84" (213 cm) from the floor.
During installation, raise the refrigerator up so there is
■
1/4" (6.35 mm) maximum between the top of the refrigerator
and the bottom of the anti-tip board(s). Do not crush the
compressor cover when raising the rear leveling legs.
NOTE: The foam gasket, on top of the compressor cover, will
compress to fit under the anti-tip board(s). There is no need to
trim the gasket.
To Install Anti-tip Boards
1. Mark the stud locations on rear wall.
2. Securely attach two 2" x 4" x 32" (5 cm x 10 cm x 81 cm)
boards to wall studs behind refrigerator. Use six
#8 x 3" (7.6 cm) (or longer) wood screws. The wood screws
must be screwed into the studs at least 1½" (3.8 cm). The
boards must overlap the compressor cover.
2" (5 cm)
2" (5 cm)
D
A. Center board 1/4" (6.35 mm)
max. above refrigerator
B. Two 2" x 4" x 32" (5 cm x
10 cm x 81 cm) boards

Connect the Water Supply

Read all directions before you begin.
IMPORTANT:
If you turn the refrigerator on before the water line is
■
connected, turn the ice maker OFF.
Connect to potable water supply only.
■
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
Connect to Water Line
Parts Needed
Minimum 7 ft (2.13 m) flexible, codes-approved water supply
■
line
Style 1—Shutoff Valve Connection
NOTE: If your water line connection does not look like Style 1,
see "Style 2—Copper Line Connection."
1. Unplug refrigerator or disconnect power supply.
IMPORTANT:
There is not enough clearance to achieve a flush installation
■
if a water shutoff valve is located in the wall behind the
refrigerator. The water shutoff should be located in the base
cabinet on either side of the refrigerator.
Before attaching the tubing to shutoff valve, flush the main
■
water supply line to remove particles and air in the water line.
Allow enough flow so that water becomes clear. Flushing the
water line may help avoid filters and/or water valves from
becoming clogged.
A B
C
C. Attach to studs with six
#8 x 3" (7.6 cm) screws
D. Compressor cover
11