Epson Stylus PHOTO 925 Setup Manual

Color Ink Jet Printer
Setup
Unpacking Unpacking
Unpacking Unpacking
Unpacking the printer and attaching the printer parts

1. Unpack the printer

paper support
printer
ink cartridges
Setting up Setting up Setting up Setting up

Install the Ink Cartridges

1. Turn on the printer. The language selection is displayed in the LCD panel.
2. Press the u or d button to select the language, then press the Select button. The
message "See your printer's documentation to complete printer setup" is
displayed.
3. Remove the new ink cartridges from their protective
bag.
4. Insert the ink cartridges.
Note:
Install all ink cartridges. The printer will not work unless
all cartridges are installed properly.
Without applying excessive force, push the ink cartridges down until they click into place.
Checking the Printer Checking the Printer
Checking the Printer Checking the Printer

Load Paper

printable side up
left edge
guide
Your printer is now set up and ready to print directly from a memory card. Refer to User's Guide and Quick Reference
for instructions. For the use with a computer, refer to the other side of this sheet.

Safety Instructions

Read all of the instructions in this section when setting up and using your printer.
When choosing a place for the printer
Avoid places subject to rapid changes in temperature and humidity. Also, keep the printer away from direct
sunlight, strong light, or heat sources.
Avoid places subject to dust, shocks, and vibrations.
Leave enough room around the printer to allow for sufficient ventilation.
Place the printer near a wall outlet where the plug can be easily unplugged.
Place the printer on a flat, stable surface that extends beyond the printer base in all directions. If you place
the printer by a wall, leave more than 10 cm between the back of the printer and the wall. The printer will not
operate properly if it is tilted at an angle.
When storing or transporting the printer, don't tilt it, stand it on its side or turn it upside down. Otherwise ink may
leak from the cartridge.
When choosing a power source
Use only the type of power source indicated on the printer's label.
Be sure your AC power cord meets the relevant local safety standard.
Do not use a damaged or frayed power cord.
If you use an extension cord with the printer, make sure that the total ampere rating of the devices plugged
into the extension cord does not exceed the cord's ampere rating. Also, make sure that the total ampere rating
of all devices plugged into the wall outlet does not exceed the wall outlet's ampere rating.
If you plan to use the printer in Germany, the building installation must be protected by a 10 or 16 amp circuit
breaker to provide adequate short-circuit protection and over-current protection for this printer.
When handling ink cartridges
Do not open the ink cartridge packages until just before you install them.
Do not shake the used ink cartridges; this can cause leakage.
Keep ink cartridges out of the reach of children. Do not allow children to drink from or otherwise handle the cartridges.
Be careful when you handle used ink cartridges, as there may be some ink remaining around the ink supply port.
If ink gets on your skin, wash the area thoroughly with soap and water. If ink gets into your eyes, flush them
immediately with water. If discomfort or vision problems remain after a thorough flushing, see a doctor immediately.
English
4022462-00
xxx
Reference
Power cord may come
attached in some countries.
catcher for 210mm
roll paper
Setup
printer software &
online guide CD-ROM
The contents may vary in certain locations.
roll paper holder
Do not remove the blue portion of the
tape seal from the top of the cartridge.
Do not touch this part.
output tray extension
c
2. Attach the printer parts
Quick
User's
Guide
Caution:
c
If the printer comes on when you plug in the power cord, turn off the printer by
pressing down the P power button until the printer lights go out.
5. Press the Maintenance button.
The printer begins ink charging. It takes about one and
half minutes. The progress bar is displayed in the LCD
panel during charging. While charging, the printer
produces a variety of mechanical sounds. This is
normal.
Caution:
c
Do not turn the power off during the ink charging process.
Do not load paper until ink charging is complete.
6. After ink charging is finished, the message "Printer setup is complete. Press 1 to
finish." is displayed in the LCD panel. Press the custom button 1.
Note:
The ink cartridges packaged with your printer are partly used during initial setup. In
order to produce high quality printouts, the print head in your printer will be fully
charged with ink. This one-off process consumes a quantity of ink and subsequent
cartridge sets will last for their full rated life.
Check the Print head nozzle
1. Press the Maintenance Button.
2. Select Nozzle Check.
3. Press the Cutom Button 1.
Good sample
If the nozzle check page print satisfactorily, press the Custom Button 1 to finish.
If the nozzle check page does not print satisfactorily, press the Custom Button 2 to clean
the Print head, then press the Custom Button 1 to check the Print Head Nozzle again.
Do not touch or remove the green IC chip that is located on the side of the cartridge.
Do not remove or tear the label on the cartridge; this can cause leakage.
Store each ink cartridge so that the bottom of its packaging faces down.
When using the printer
Do not put your hand inside the printer or touch the ink cartridges during printing.
Do not block or cover the openings in the printer's cabinet.
Do not attempt to service the printer yourself.
Unplug the printer and refer servicing to qualified service personnel under the following conditions:
The power cord or plug is damaged; liquid has entered the printer; the printer has been dropped or the cabinet
damaged; the printer does not operate normally or exhibits a distinct change in performance.
Do not insert objects through the slots in the printer's cabinet.
Take care not to spill liquid on the printer.
Leave the ink cartridges installed. Removing the cartridges can dehydrate the printer head and may prevent
the printer from printing.
When using the Automatic Roll Paper Cutter
Keep the cutter out of the reach of children.
Do not touch the paper ejection part and cutter blade.
Do not place the cutter on an unstable surface (such as on an unstable table or a tilted surface).
Do not disassemble or modify the cutter.
Cautions and Notes
Cautions must be observed to Notes contain important information
avoid damage to your and useful tips on the operation of your
equipment. printer.
Print head needs to be cleaned
Segments are missing