Print controller for bizhub pro c500 printer (212 pages)
Summary of Contents for Konica Minolta IC-401
Page 1
INSTALLATION GUIDE IC-401 (Interface Kit VI-501) Image Controller C350 NOTE • Before setting up, be sure to unplug the power cord of the machine. • Be sure to keep all packing materials out of the reach of children. 4342-7747-12 Printed in Japan...
Page 2
Image Controller IC-401 (Interface Kit VI-501) ■ Operating Environment ■ Outline of Setup The image controller operates under the following environment. Set up the image controller according to the procedures shown below. PCL driver (only for the Windows operating system) and PS driver are available.
Page 3
Image Controller IC-401 (Interface Kit VI-501) 1. Check the contents of the enclosed interface kit. Before starting to set up, check that the following accessories are included with this unit. 1. Controller mounting plate .................... 1 2. Controller cover ......................1 3.
Page 4
Image Controller IC-401 (Interface Kit VI-501) 2. Installation ■ Installing the PWB-EFI Board 5. Remove the shield cover from the rear of the copier. (12 screws) 1. Turn off the copier, and then unplug it. 2. Remove the lower rear cover of the copier.
Page 5
Image Controller IC-401 (Interface Kit VI-501) 7. Disconnect the copier cable. (2 screws) 9. Remove the three screws for the controller board Assy. C4342U227AA C4342U225AA 10. Install the enclosed shoulder screws (6) at the positions where screws were removed 8. Remove the controller board cover at the in step 9.
Page 6
Image Controller IC-401 (Interface Kit VI-501) 11. Securely insert connector PJ1 on the PWB- 13. Install the controller board cover removed in EFI board (5) into the connector on the con- step 8. (9 screws) troller board Assy. During installation, also secure the PWB- EFI board with the enclosed screws.
Image Controller IC-401 (Interface Kit VI-501) ■ Installing the Fiery Controller Board 2. Secure the Fiery controller board with the six screws (7). NOTE Start the installation procedure after removing 4 plastic from the four corners of the controller mounting plate.
Page 8
Image Controller IC-401 (Interface Kit VI-501) ➁ 5. Install the fan assembly on top of the shoul- 7. Install the interface kit cover, and then der screws, and then secure it using the secure it using the 16 screws (8).
Image Controller IC-401 (Interface Kit VI-501) 9. Secure the interface kit with the two screws 12. Remove the screw on the rear cover of the (8) for installing the controller. copier and the screw on the plate at the back of the cassette.
Image Controller IC-401 (Interface Kit VI-501) 14. Connect the printer cable to the copier. 16. Use one screw (7) to attach the plate to the standard printer controller network port C4342U213AA C4342U232AA 15. Attach a CKN clamp at the lower-left corner of the interface kit, and then pass the printer cable though the clamp.
Page 11
Image Controller IC-401 (Interface Kit VI-501) 3. Specifying the Copier Settings 4. In the Peripheral Setting screen, touch [Controller 2]. From the copier, specify the necessary settings for using the controller. Specifying the External Interface Operating Mode 1. Display the Tech. Rep. Mode screen.
Page 12
Image Controller IC-401 (Interface Kit VI-501) Specifying the Priority Device Specify the print timing for received print jobs. 4. Touch [Copier] or [Printer]. 1. Press the [Utility] key on the copier. If “Copier” was selected: Print jobs are queued as a job when the data for all 2.
Page 13
Image Controller IC-401 (Interface Kit VI-501) 5. Checking With a Test Print 7. Select the region as described in step After setting up the controller, print the Configuration page to check that the controller is operating correctly. Printing procedure 1. Press the [Utility] key on the copier.
Before installing the patch file The controller is recognized as KONICA MINOLTA printer in a network management tool (EX. PageScope Net Care) at the time of use. In addition, the KONICA MINOLTA logo appears at the top of the PageScope Web Connection page.
Image Controller IC-401 (Interface Kit VI-501) 8. Setting the User Environment Entering the Controller Setup Mode Use the controller operation panel to print test pages and specify the various settings. The following procedures are basically for administrators. Refer to the following only if a 1.
Page 16
Image Controller IC-401 (Interface Kit VI-501) <Performing operations using the controller operation panel> • To select [Yes] or [No], touch the up and down arrow buttons until the desired setting is 2. With the controller idle, touch [MENU] displayed. to display the Functions menu.
Page 17
Image Controller IC-401 (Interface Kit VI-501) Common Settings for Controllers 2. Follow the procedure below to specify the settings necessary for printing on a net- work. Change the printer port from the one specified when the printer driver was (The recommended settings are underlined and the settings within [ ] are the default set- installed in step 1 to a port for a network connection, and then change any controller tings.)
Page 18
Image Controller IC-401 (Interface Kit VI-501) ■ SMB printing ■ LPD (LPR) printing Controller settings Controller settings (The recommended settings are underlined and the settings within [ ] are the default set- (The recommended settings are underlined and the settings within [ ] are the default set- tings.)
Page 19
Image Controller IC-401 (Interface Kit VI-501) ■ Network Printing on a Macintosh Computer For Windows 2000, XP and Server 2003: 1. Display the printer properties. Mac OS 8.6 - 9.2 AppleTalk printing 2. Click the Ports tab, and then click [Add Port...]. The Printer Ports dialog appears.
Page 20
French fr.lproj IC-401. German de.lproj 5. If “LPR Printers using IP” was selected, type the IP address or DNS name for IC-401 into the LPR Printer’s Address field. Italian it.lproj 6. Clear the [Use Default Queue on Server] check box.
Page 21
Image Controller IC-401 (Interface Kit VI-501) ■ NetWare environment PC Settings 1. Start up the Add Printer Wizard, and then select [Network Printer]. Settings for NetWare printing 2. Display the printer on the network (click [Browse] for Windows 98 and Me, or click The controller supports the following NetWare environments.
Page 22
Image Controller IC-401 (Interface Kit VI-501) ■ Performing a test print from client PC Check Possible Cause Action This operation is performed to check if the settings for the connection with the computer Is there a response The print destination port Specify the correct port.
Page 23
Image Controller IC-401 (Interface Kit VI-501) 9. Specify the scanner setting The procedure for specifying settings using PageScope Web Connection is described below. ■ Scan to FTP Server • Start up PageScope Web Connection. 1. From the controller operation panel, select [Run Setup], [Network Setup], [Service •...
Page 24
Image Controller IC-401 (Interface Kit VI-501) ■ Scan to Mailbox 5. Specify the necessary settings for the selected transmission method. 6. Click [Apply]. 1. From the controller operation panel, display the screen that appears when [Run Setup], then [Server Setup] is selected.