Table of Contents
Advertisement
Section
Optional Control Signal Wiring
Optional Control Signal Wiring Continued
Control Inputs (Optional)
Control Inputs (Optional)
These control inputs are optional. Their reference (common) is CREF at X3-7
These control inputs are optional. Their reference (common) is CREF at X3-7
(see Figure 3-3). The voltage range is +12VDC to +29VDC for these inputs.
(see Figure 3-3). The voltage range is +12VDC to +29VDC for these inputs.
They may be used by a PLC or other signal source within your application.
They may be used by a PLC or other signal source within your application.
1. C o n n e c t the Machine Input 1 (MAI1) signal to X3-16.
1.
Connect the Machine Input 1 (MAI1) signal to X3-16.
2. C o n n e c t the Machine Input 2 (MAI2) signal to X3-17.
2.
Connect the Machine Input 2 (MAI2) signal to X3-17.
These inputs are galvanically isolated. Their reference (common) is CGND at
These inputs are galvanically isolated. Their reference (common) is CGND at
X3-8 of Figure 3-3.
X3-8 of Figure 3-3.
3. C o n n e c t the Pulse Input signal to X3-14.
3.
Connect the Pulse Input signal to X3-14.
4. C o n n e c t the Direction Input signal to X3-15.
4.
Connect the Direction Input signal to X3-15.
Control Outputs (Optional)
Control Outputs (Optional)
Four Opto Isolated outputs are available for "Active Low" (Sink) use.
Four Opto Isolated outputs are available for "Active Low" (Sink) use.
Connect one or more of the control outputs as follows: (see in Figure 3-9).
Connect one or more of the control outputs as follows: (see in Figure 3-9).
1. C o n n e c t the Ground Return of the power source to X3-8.
1.
Connect the Ground Return of the power source to X3-8.
2. C o n n e c t a customer provided +24VDC source (range = +12VDC to
2.
Connect a customer provided +24VDC source (range = +12VDC to
+29VDC) to X3-6 the CIV input (Customer Input Voltage).
+29VDC) to X3-6 the CIV input (Customer Input Voltage).
3. C o n n e c t Machine Output 1 (MAO1) X3-18 to PLC.
3.
Connect Machine Output 1 (MAO1) X3-18 to PLC.
4. C o n n e c t Machine Output 2 (MAO2) X3-19 to PLC.
4.
Connect Machine Output 2 (MAO2) X3-19 to PLC.
5. C o n n e c t the Drive OK load to X3-20.
5.
Connect the Drive OK load to X3-20.
Ground Return
Ground Return
* 24VDC nominal at 100mA minimum.
* 24VDC nominal at 100mA minimum.
Note: T h e s e outputs are programmable. Refer to software setup manual for
Note:
These outputs are programmable. Refer to software setup manual for
further details.
further details.
3-12
3–12
M
Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com
Figure 3-9 Optional Control Outputs
Figure 3-9 Optional Control Outputs
8
CIV .>
CIV *
Machine Output 1
Machine Output 1
Machine Output 2
Machine Output 2
Drive OK
Drive OK
N
1
Continued
X3
X3
8
6
6
18
18
19
19
20
20
2
2
To Customer
To Customer
Provided PLC
Provided PLC
9
MN1229
Hide quick links:
Advertisement
Table of Contents
