Table of Contents
Related Manuals for ADC ETU-751C List 1
Summary of Contents for ADC ETU-751C List 1
- Page 1 G .7 WorldDSL ANUAL HDSL ELECTABLE INE AND ESKTOP NITS UTU-701C List 1 Universal Termination Unit Part Number: 150-1422-01C ETU-751C List 1 ETSI Termination Unit Part Number: 150-1432-01C...
- Page 2 Contents herein are current as of the date of publication. ADC reserves the right to change the contents without prior notice. In no event shall ADC be liable for any damages resulting from loss of data, loss of use, or loss of profits, and ADC further disclaims any and all liability for indirect, incidental, special, consequential or other similar damages.
- Page 3 Unpack each container and inspect the contents for signs of damage. If the equipment has been damaged in transit, immediately report the extent of damage to the transportation company and to ADC DSL Systems, Inc. Order replacement equipment, if necessary.
- Page 4 Inspecting Shipment 700-701-100-02 August 9, 2002 ETU-701C and ETU-751C List 1...
-
Page 5: Table Of Contents
Inspection, Safety, and Equipment Repair _______________________________________________ 22 Inspection ...22 Safety ...22 Equipment Repair ...22 Installation and Startup _______________________________________________________________ 23 UTU-701C Line Unit Installation ...23 ETU-751C Desktop Unit Installation ...24 HDSL Startup and Synchronization...24 ETU-701C and ETU-751C List 1 August 9, 2002 Table of Contents... - Page 6 ECA-802 Connector Adapter (DB9M to RJ-45)... 66 ECA-804 Connector Adapter (DB9M to Four-Position Terminal Block) ... 68 Product Support _____________________________________________________________________ 69 Abbreviations _______________________________________________________________________ 70 Certification and Warranty ______________________________________________ Inside Back Cover August 9, 2002 700-701-100-02 ETU-701C and ETU-751C List 1...
- Page 7 1. Leased Line Data Application on a Single-pair G.703 Network ...3 2. UTU-701C Line Unit Front Panel ...4 3. ETU-751C Desktop Unit Front Panel...4 4. ETU-751C Desktop Unit Rear Panel ...7 5. Line and Desktop Unit Functional Block Diagram ...11 6. Typical Structured Mode Application...14 7.
- Page 8 46. ECA-801 D25M to DB15F (X.21) Connector Adapter, Part Number 150-1470-01 ... 66 47. ECA-802 DB9M to RJ-45 Connector Adapter, Part Number 150-1472-01 ... 67 48. ECA-804 DB9M to Four-Position Terminal Block Connector Adapter, Part Number 150-1474-01 ... 68 viii August 9, 2002 700-701-100-02 ETU-701C and ETU-751C List 1...
- Page 9 2. Transmission Ranges with 0 db ETSI Noise ...3 3. Line and Desktop Unit Front Panel Components ...5 4. Line and Desktop Unit Front Panel LED Indications ...6 5. ETU-751C Desktop Unit Rear-Panel Components ...7 6. WorldDSL Product Compatibility ...8 7. Typical Structured Mode System Settings...15 8.
- Page 10 37. ECA-801 DB25M to DB15F (X.21) Connector Adapter Pinouts... 66 38. ECA-802 DB9M to RJ-45 Connector Adapter Pinouts ... 67 39. ECA-804 DB9M to Four-Position Terminal Block Connector Adapter Pinouts... 68 August 9, 2002 700-701-100-02 ETU-701C and ETU-751C List 1...
-
Page 11: Overview
All other aspects of ETU functionality are identical to LTUs or NTUs. The ETU-751C has a G.703 interface and contains a power supply that accepts 100 to 240 volt, 50 or 60 Hz, AC power. -
Page 12: Emu Firmware Compatibility
G.703 port are replaced by idle codes at the G.703 output. The UTU-701C and ETU-751C have HDSL payload rates ranging from 256 kbps to 2048 kbps. The desired HDSL payload rate is selected in time slot increments of 64 kbps from the system settings menu of the LTU-configured unit. -
Page 13: Hdsl Technology
HDSL T ECHNOLOGY HDSL is the core technology for ADC’s WorldDSL line of LTUs, UTUs, and ETUs. Rate selectable HDSL enables these units to transmit and receive digital data at various rates over various distances on one twisted pair of copper wire. Both outbound and inbound signals are delivered on the same pair of wires by using echo cancellation techniques. -
Page 14: Front And Rear Panel Components
The line and desktop unit front panels are shown in panels are described in Table 3 on page 5 The ETU-751C desktop unit rear panel is shown in described in Table 5 on page 7. The pinouts for the desktop unit rear panel connectors are listed in... -
Page 15: Line And Desktop Unit Front Panel Components
For example, a warranty control number of "803R07" would indicate a warranty beginning in the year 1998 (8), during the month of March (03), and line card revision number R07. Unit ID label (ETU-751C) Identifies the model number, manufacturer, part number, and input voltage range of the ETU. Includes the CE mark, certifying that the unit is in compliance with directive EN300 386-2. -
Page 16: Line And Desktop Unit Front Panel Led Indications
Overview Table 4 defines the system states indicated by the front panel LEDs. When power is applied to the unit, one of the LEDs listed in Table 4 will always be on. Table 4. Line and Desktop Unit Front Panel LED Indications Mode HDSL SYNC LED Steady green... -
Page 17: Etu-751C Desktop Unit Rear Panel
700-701-100-02 Figure 4. ETU-751C Desktop Unit Rear Panel Table 5. ETU-751C Desktop Unit Rear-Panel Components Item Description D15F 120 G.703 Connects E1 balanced 120 connector BNC 75 In/Out G.703 Connects E1 unbalanced 75 connectors D9F HDSL line connector Connects the HDSL pair to the enclosure. -
Page 18: Worlddsl Product Compatibility
(d) The ECA-80x series of connector adapters and their pinouts are listed in beginning on page OMPATIBILITY Table 6. WorldDSL Product Compatibility Rate-Selectable HDSL Units Shelves and Enclosures for UTU-701C Connector Adapters for ETU-751C August 9, 2002 700-701-100-02 Table Part Number 150-1422-02C 150-1422-12C... -
Page 19: August
700-701-100-02 PECIFICATIONS HDSL Interface Line Code Line Rate (selectable in increments of 64 kbps) Up to 2048 kbps Protection Compliance Transmission Ranges (± 200 m): Transmission Ranges with 0 dB ETSI Noise 0.4 mm (26 AWG) HDSL Line Single Twisted-Pair Rate (kbps) Copper Wire 4.1 km (13,451 ft.) -
Page 20: Regulatory Approvals
E1 Interface External Clock HDSL Loop History E1 and HDSL Interface Alarm Power Requirements UTU-701C Local input voltage Consumption (typical) ETU-751C Local input voltage Consumption (typical) Environmental Operating Temperature Range Humidity Storage Temperature Storage Humidity Regulatory Approvals CE Mark Certification... -
Page 21: Functional Description
700-701-100-02 UNCTIONAL This section provides a functional description of the line and desktop units, including major components, single-pair application mode, alarms, and testing (including monitoring and loopbacks). AJOR OMPONENTS The major components of the line and desktop units include: • G.703 interface (75 or 120 ) •... -
Page 22: G.703 Interface
Functional Description G.703 Interface The G.703 interface performs the following functions: • provides a jumper-selectable 75 or 120 DTE interface (see locations) • allocates full or fractional portion of the total 2048 kbps bandwidth to and from the G.703 interface •... -
Page 23: Power Sources
AC-to-DC power supply (when provided). • The ETU-751C desktop unit receives power from a source of 100 to 240 volt, 50 or 60 Hz, AC power. Input voltage for the UTU-701C line unit (nominal -48 Vdc, tolerance -36 to -72 Vdc) must be supplied by an isolated DC source that complies with TNV or earthed SELV requirements of the latest version of IEC 950. -
Page 24: Rate Selectable Application Modes And Options
(4.4 miles) time slots selected. The UTU-701C and ETU-751C each have 32 time slots with a bandwidth of from 256 kbps to 2048 kbps (1 to 32 time slots selected). Each time slot represents a 64 kbps increment of the available bandwidth. -
Page 25: Typical Structured Mode System Settings
700-701-100-02 Table 7. Typical Structured Mode System Settings Options Application Mode Primary Timing Source G.703 Port CRC-4 Mode Idle Code Data Rate / # of TSs Beginning TS Primary Timing Source G.703 Port CRC-4 Mode Idle Code Data Rate / # of TSs Beginning TS For applications requiring fractional use of the G.703 port, embedded generation and detection of CRC-4 information, and A-bit insertion, select less than 32 time slots to invoke the structured mode. -
Page 26: Unstructured Mode
2048 kbps transport of data between a DTE connected to an UTU-701C and a DTE connected to an ETU-751C. The settings in primary timing source. Timing at the ETU side is recovered from the received G.703 signal. This application is... -
Page 27: G.704 Framing And Rate Selectable Hdsl
700-701-100-02 G.704 Framing and Rate Selectable HDSL Time slots 0 and 16 are always transported in accordance with the G.704 framing standard. Although not used by G.703 to transport data, the rate-selectable HDSL interface treats time slots 0 and 16 as a 128 kbps increase in the HDSL payload rate. -
Page 28: Performance Monitoring And History
Functional Description ERFORMANCE ONITORING AND The UTU and ETU units provide extensive real time, non-disruptive monitoring of HDSL transmission performance parameters for all units in a circuit. Performance of the user interface ports is also monitored. Current cumulative counts of the past 24 hours and historical data in the form of 24-hour history (in 15-minute increments) and a 7-day history (in 24-hour increments) are available to assist in identifying problem sources during troubleshooting. -
Page 29: Loopbacks
700-701-100-02 Table 11. HDSL Transmission and Application Interface Alarms Alarm Description HDSL Alarms HDSL alarms include: Margin (MAR) Margin has fallen below threshold set for the HDSL interface. Errored Seconds (ES) Errored seconds count has exceeded threshold set for the HDSL interface. Loss of Sync Word Loss of sync word at the HDSL interface. -
Page 30: Loopbacks Selected At Front Panel Pushbuttons And Console Screens
Functional Description Table 12. Loopbacks Selected at Front Panel Pushbuttons and Console Screens Loopback Description The two loopbacks that follow can be selected from the LOC and REM front-panel pushbuttons, the console screens, or the management unit interface. LOC Pushbutton—Local This is an analog loopback implemented in both HDSL transceivers, and enables a complete checkout HDSL Loopback of the local equipment by looping back data at the furthest point before the transmission media. -
Page 31: Ber Testing
700-701-100-02 Table 13 summarizes the equivalent loopbacks for two different activation methods: • LTU and NTU LOC and REM buttons • console screen Test menus (see Front Panel LTU LOC button LTU REM button NTU LOC button NTU REM button (a) Activated from console screen Test menu at LTU. -
Page 32: Inspection, Safety, And Equipment Repair
Open the line or desktop unit shipping carton and inspect the contents for signs of damage. If the equipment was damaged in transit, immediately report the extent of the damage to the transportation company and to ADC (see “Product Support” on page 69). -
Page 33: Installation And Startup
700-701-100-02 NSTALLATION AND This section describes the installation and startup procedures for the line and desktop units. UTU-701C L Perform the following steps to install the UTU-701C line unit. The chassis ground of the shelf or remote enclosure receiving these units must be connected to earth ground for protection of the equipment and for safety of personnel. -
Page 34: Etu-751C Desktop Unit Installation
ETU-751C D ESKTOP Perform the following steps to install an ETU-751C desktop unit. Insert the AC power cord into the power cord receptacle on the ETU rear panel. Plug the power cord into a source of 100 V to 240 V, 50 or 60 Hz AC power. -
Page 35: System Configuration
700-701-100-02 YSTEM ONFIGURATION Each line unit provides a system-wide view of the entire HDSL circuit, including the remote unit. After establishing communication with the remote line card, provisioning information can be set and performance can be monitored from the local unit. If the HDSL link is down, the only parameters that can be changed are those on the local line unit. -
Page 36: Modem Connection
System Configuration To connect and configure a maintenance terminal: Connect a serial cable from the maintenance terminal 9-pin COM port to the line or desktop unit console port connector (Figure 11). Ensure the Data Terminal Ready (DTR) signal from the terminal is connected as the HDSL card will not communicate without it. -
Page 37: Logging On
700-701-100-02 OGGING To log on to the maintenance terminal console screen: Press the SPACEBAR several times to display the Logon Password screen ENTER key is the factory default password. If you establish a different password, you must type the new password (single word, no spaces, up to eight characters) on a subsequent log on. If the system does not respond, verify that the Hardware Flow Control of the maintenance terminal is set to NONE . -
Page 38: Console Screen Structure
System Configuration ONSOLE CREEN TRUCTURE The following sections describe the structure of the console screen and how to navigate through its menus and related displays. The structure of the console screen displays and drop-down menus is shown in console screen menu bar identify each display and menu. The arrows in the menu bar following the Monitor, History, and Config names indicate the presence of a drop-down menu or sub-menu. -
Page 39: Console Screen Menus
700-701-100-02 Table 14 describes the drop-down menus selected from the console screen. Menu Name Function Main Display the Main console screen to: • View the circuit configuration • View performance summary information • View alarm summary information Monitor Monitor the past 24-hour performance of the LTU interfaces, NTU interfaces, or HDSL spans. -
Page 40: Reading And Navigating Menus
System Configuration EADING AND AVIGATING The menu and status bars appear on all console screens. The information on the rest of the screen varies depending on the function of the menu or screen. The menu bar displays the name of each menu. Choosing Monitor, History, or Config from the menu bar drops down a menu of available options. -
Page 41: Console Screen Navigation Keys
700-701-100-02 Use the keys described in Table 16 Table 16. Console Screen Navigation Keys Press this Key To Perform this Function Alpha-numeric keys Type the underlined or highlighted letter to select and execute a menu item. For example on the Main console menu, type Also use these key to enter values in text fields. -
Page 42: Config Menu Options
System Configuration Config Menu Options Type at the console screen (Figure options and the order of system configuration. Table 17. Config Menu Options and Recommended Order of System Configuration Use this Option Terminal Settings Select the best viewing mode for the console screen. Date and Time Set the system date and time. -
Page 43: Configure Terminal Settings
700-701-100-02 Configure Terminal Settings The console screens use line drawing characters to enclose menu selections and dialog boxes. Because not all maintenance terminals and terminal emulation programs adhere consistently to the VT100 standard, the HDSL card allows you to adjust the display for best results on a given terminal. -
Page 44: Configure Date And Time
System Configuration Configure Date and Time 1Type at the Config drop-down menu to display the Config Date and Time menu Type the date in DD/MM/YY format, then press Type the time in HH : MM format (24-hour clock), then press The system date and time appear on the status line of the console screen and is useful when viewing alarm histories. -
Page 45: Change Password
Retype the new password (up to eight characters) to confirm its accuracy. When changing the default password ( password cannot be recovered if it is forgotten. Contact ADC if assistance is needed (see “Product Support” on page UTU-701 and ETU-751 List 1 ENTER ), save the new password in a secure place. -
Page 46: Configure Circuit Id
System Configuration 700-701-100-02 Configure Circuit ID The circuit ID appears on the status line of each console screen. Choose a unique circuit ID for each HDSL card. 1Type at the Config drop-down menu to display the Config Circuit ID menu (Figure 20). -
Page 47: Configure System Settings
Type at the Config drop-down menu to display the Config System Settings menu. Config System Settings menu for the UTU-701C and ETU-751C. Do the following for each system option setting to be changed. options displayed in the Config System Settings menu. The settings in boldface type are factory default settings. -
Page 48: Fields And Options Displayed In Config System Settings Menu
(a) SINGLE is the only application mode and MANUAL is the only rate mode. (b) UTU-701C and ETU-751C have 32 time slots available for HDSL payload rates of 256 kbps to 2048 kbps. (c) An HDSL Payload Rate of 64 kbps (1 time slot) is transmitted at 256 kbps (see (d) Payload rates are displayed in the Config LTU and Config NTU Interface menus as Data Rate/# of TSs (data rate/number of time slots). -
Page 49: Configure Ltu And Ntu Interfaces
700-701-100-02 Configure LTU and NTU Interfaces Select and configure the LTU- and NTU-related operating parameters as follows: Type one of the following at the Config drop-down menu to display the Config LTU or NTU Interface menu: • for the Config LTU Interface menu •... -
Page 50: Fields And Options In Displayed Config Ltu And Config Ntu Interface Menus
System Configuration Do the following for each interface option to be changed. in the Config LTU and Config NTU Interface menus. • Use the or the key to select the sub-menu item to be changed. • Use the SPACEBAR to toggle to the appropriate option or type in the correct information, then press ENTER to select the option. -
Page 51: Configure Alarms
700-701-100-02 Configure Alarms Use the Config Alarms menu to configure LTU and NTU Interface alarm parameters and the HDSL span alarm parameters. When setting alarm parameters for LTUs and NTUs, keep the following rules in mind: • Disabled alarms do not cause LED indications and are not stored in history. Console screen menu alarm history reports are not generated. -
Page 52: Config Alarms Ltu Interface Menu
System Configuration Alarms for LTU and NTU Interface Type one of the following at the Config Alarms drop-down menu to display the Config Alarms LTU or Config Alarms NTU Interface menu: • for the Config Alarms LTU Interface menu • for the Config Alarms NTU Interface menu Figure 25. -
Page 53: Config Alarms Hdsl Span 1 Menu
700-701-100-02 Table 20. Fields Displayed in Config Alarms LTU and Config Alarms NTU Interface Menus Field Loss of Signal (LOS) Loss of Frame Alignment (LFA) Receive Alarm Indication Signal (AIS) Remote Alarm Indication Signal (RAI) Loss of Clock (LOC) HDSL Span 1 Alarms Type at the Config Alarms drop-down menu to display the Config Alarms HDSL Span 1 menu Figure 27. -
Page 54: Set To Factory Defaults
Not supported. These units do not supply power to other units. ET TO ACTORY EFAULTS Set to Factory Dflts is the screen from which all operating options can be reset to the ADC factory defaults. Type at the Config drop-down menu to display the Set to Factory Dflts screen Press ENTER to reset value to factory defaults. -
Page 55: Logging Off
700-701-100-02 Do one of the following: • Type to keep the current settings. • Type to reset values to factory defaults. The system resets and both LTU and NTU units go through their respective synchronization processes. If loops are down or are in update mode while Set to Factory Dflts is enabled, only the local unit will restart. -
Page 56: Viewing Status
Viewing Status IEWING TATUS The following sections describe the screens that display status and system information, such as current alarm status, performance history, product, and configuration information. View status using a maintenance terminal or PC running a terminal emulation program connected to the V.24 (RS-232) console port. -
Page 57: Fields Displayed In Main Console Screen
700-701-100-02 Table 24 describes the fields displayed on the Main console screen. Table 24. Fields Displayed in Main Console Screen Field Description G.703 Indicates the interface standard for G.703 data port. n TS Indicates the number of time slots (n) mapped to the G.703 interface. Timing Indicates the primary source the unit uses for clock synchronization: External 2.048 MHz clock. -
Page 58: Monitor Menu
Viewing Status ONITOR The Monitor menu contains the following options: • LTU Interface screen that displays the 24 hour and cumulative count of errors at the LTU G.703 port. • NTU Interface screen that displays the 24 hour and cumulative count of errors at the NTU G.703 port. •... -
Page 59: Monitor Ltu Interface Screen
700-701-100-02 Monitor LTU Interface Screen At the Monitor menu (Figure 30), type describes the fields displayed in the Monitor LTU and Monitor NTU Interface screens. Table 25. Fields Displayed in Monitor LTU and Monitor NTU Interface Screens Field Description Errored Seconds (ES) The number of one-second intervals in which at least one bipolar violation (BPV) or one CRC-4 24 Hour Count error was detected at the G.703 input port during the last 24hours. -
Page 60: Monitor Ntu Interface Screen
Viewing Status Monitor NTU Interface Screen At the Monitor menu (Figure 30), type The fields displayed in the Monitor NTU Interface screen are identical to those displayed in the Monitor LTU Interface screen (see Table 25 on page to display the Monitor NTU Interface screen 49). -
Page 61: Monitor Hdsl Span 1 Screen
700-701-100-02 Monitor HDSL Span 1 Screen The HDSL Span 1 screen (Figure 1 interface. A span is defined as the link between two HDSL units (that is, from an LTU to an NTU) which, in this case, is comprised of a single loop (that is, one twisted-copper pair). The values under the LTU-1 column represent HDSL Span 1 as measured by the LTU. -
Page 62: History Menu
Viewing Status ISTORY The History menu contains the following status screens: • LTU/NTU Interfaces that display alarm performance history for the LTU and NTU interface. • HDSL Span that displays 24-hour, 7-day, and alarm performance history for the HDSL span. The History menu also provides the option to clear the 24-hour, 7-day, and alarm history screens. -
Page 63: Ltu And Ntu Interface Performance History Screens
700-701-100-02 LTU and NTU Interface Performance History Screens At the History menu (Figure 34), type At the History menu (Figure 34), type UTU-701 and ETU-751 List 1 to select the History LTU Interface menu Figure 35. History LTU Interface Menu to select the History NTU Interface menu Figure 36. -
Page 64: Ltu Interface Alarm History Screen
Viewing Status Only the Alarm History screen is available for the LTU and NTU interfaces. The 24 Hour and 7 Day History screens, as well as the Alarm History screen, are available for HDSL Span 1. LTU and NTU Interface Alarm History Screens At the History LTU or History NTU Interface menu, type the LTU Interface Alarm History screen is shown in Figure 37. -
Page 65: Hdsl Span Performance History Screens
700-701-100-02 HDSL Span Performance History Screens At the History menu (Figure 34), type The History HDSL Span 1 menu contains three viewing options: • 24 Hour History • 7 Day History • Alarm History HDSL Span 1 24 Hour History Screen At the History HDSL Span 1 menu Span 1 (Figure... -
Page 66: Day History Status Screen For Hdsl Span 1
Viewing Status The 24 Hour History screen for HDSL Span 1 contains three columns of data that show (from left to right) the: • Starting time of each 15-minute interval. • Number of ES/UAS at the LTU end of the HDSL span (LTU-1) for each interval. A dash (-) represents a count of zero. -
Page 67: Alarm History Status Screen For Hdsl Span 1
700-701-100-02 HDSL Span 1 Alarm History Screens At the History HDSL Span 1 menu Span 1 (Figure 41). Figure 41. Alarm History Status Screen for HDSL Span 1 Table 28 describes the four columns of data contained in each HDSL Span Alarm History screen. Column Description Alarm... -
Page 68: Clear History Screens
Viewing Status Clear History Screens Use the following options to clear the 24 Hour, 7 Day, or Alarm History status screens: • Clr 24 Hr Hist: clears all of the 24-hour history error counters • Clr 7 Day Hist: clears all of the 7-day history error counters •... -
Page 69: Inventory Screen Data
Days Op Displays the number of days the LTU, NTU, and any doubler units have been in operation. SW Part # Displays the ADC part number of the firmware. Chksum Displays the checksum of the LTU, NTU, and doubler unit proms. -
Page 70: Testing
Testing ESTING From the main console screen (Figure loopback and BER tests (Figure Table 30 on page 61 lists the Test menu options. section of the test menu. Loopbacks remain active until the timeout elapses or the configuration changes. The loopback location and status are indicated on the network diagram portion of the test menu, with "@@]"characters as follows: •... -
Page 71: Test Menu Options
700-701-100-02 Operating Option Default Setting Network Diagram Shows the loopback position and direction when the loopback is enabled and active. Lpbk Dir Selects one of three loopback direction modes: No loopbacks are active. NETWORK The loopback selected in Loopback Position is directed toward the network equipment connected to the LTU. -
Page 72: Firmware Download Utility
Firmware Download Utility IRMWARE OWNLOAD The Firmware Download Utility is a separate program and is not available from the console screen menus. This section describes the ETSI Firmware Download utility and how to use it to upgrade the line and desktop unit firmware. -
Page 73: Etsi Firmware User Selectable Download Menu Options
700-701-100-02 Initiate the Download and Navigate the Menus To initiate the download process, go to the DOS prompt and type: dnl. Selectable Download Menu Options. Table 32. ETSI Firmware User Selectable Download Menu Options Option Description PORT Provides support for two communication ports: COM1 at Hex 3F8 COM2 at HEX 2F8 SPEED... -
Page 74: Reference Information
Reference Information EFERENCE NFORMATION This section lists the pinouts for the ETU-751C rear panel connectors and the ECA-80x connector adapters. ETU-751C C ONNECTOR The pinouts for the ETU-751C rear panel connectors are listed in Table 34. D9F HDSL Line Connector Pinouts (a) All other pins are not used. -
Page 75: Eca-800 Connector Adapter (Db25M To M34F For V.35)
700-701-100-02 ECA-800 C ONNECTOR The ECA-800 connector adapter panel to a standard V.35 34-pin female connector. Figure 45. ECA-800 DB25M to M34F (V.35) Connector Adapter, Part Number 150-1470-01 Table 36. ECA-800 DB25M to M34F (V.35) Connector Adapter Pinouts DB25M Connector Signal Shield Send Data A... -
Page 76: Eca-801 Connector Adapter (Db25M To Db15F For X.21)
Reference Information ECA-801 C ONNECTOR The ECA-801 connector adapter panel to a standard X.21 15-pin female connector. Figure 46. ECA-801 D25M to DB15F (X.21) Connector Adapter, Part Number 150-1470-01 Table 37. ECA-801 DB25M to DB15F (X.21) Connector Adapter Pinouts DB25M Connector Signal Send Data A Send Data B... -
Page 77: Eca-802 Db9M To Rj-45 Connector Adapter, Part Number 150-1472-01
700-701-100-02 Figure 47. ECA-802 DB9M to RJ-45 Connector Adapter, Part Number 150-1472-01 Table 38. ECA-802 DB9M to RJ-45 Connector Adapter Pinouts DB9M Connector Signal HDSL Loop 1 (Ring) HDSL Loop 1 (Tip) HDSL Loop 2 (Ring) HDSL Loop 2 (Tip) (a) Pins 1, 6, 4, and 5 not used on single-pair HDSL cards. -
Page 78: Eca-804 Connector Adapter (Db9M To Four-Position Terminal Block)
Reference Information ECA-804 C ONNECTOR ERMINAL LOCK The ECA-804 connector adapter panel to a four-position terminal-block style connector. Figure 48. ECA-804 DB9M to Four-Position Terminal Block Connector Adapter, Part Number 150-1474-01 Table 39. ECA-804 DB9M to Four-Position Terminal Block Connector Adapter Pinouts Four-Position Terminal Block Signal HDSL Loop 1 (Ring) -
Page 79: Product Support
ADC Customer Service Group provides expert pre-sales and post-sales support and training for all its products. Technical support is available 24 hours a day, 7 days a week by contacting the ADC Technical Assistance Center at the number listed below. -
Page 80: Abbreviations
Abbreviations BBREVIATIONS Alarm Indication Signal Alarm ANSI American National Standards Institute American Wire Gage Bit Error Rate Centigrade Communication Cyclic Redundancy Check Clear To Send D15F D-type 15-pin Female Connector D25F D-type 25-pin Female Connector D-type 9-pin Female Connector Decibel Data Communications Equipment Detector Download... -
Page 81: Certification And Warranty
90-day warranty period is, at ADC’s option, either (a) return of the price paid or (b) repair or replace of the software. ADC also warrants that, for a period of thirty (30) days from the date of purchase, the media on which software is stored will be free from material defects under normal use. - Page 82 ADC DSL Systems, Inc. 14402 Franklin Avenue Tustin, CA 92780-7013 Tel: 714.832.9922 Fax: 714.832.9924 Technical Assistance : 700-701-100-02 OCUMENT ISO 9001/TL 9000 ´,JE¶1l¨ 1242371 DNV Certification, Inc. REGISTERED FIRM...