Philips FW-M55/22 User Manual page 11

To start the demonstration mode
• Press and hold Ç (on the system only)
for 5 seconds when the system is in
standby mode.
™ The demonstration will begin.
Easy Set
EASY SET allows you to store all available
radio stations and RDS stations
automatically.
1 Press and hold STANDBY ON (on the
system only) for 5 seconds ; when the
system is in standby or demonstration
mode.
™ "EASY SET" will be displayed,
and followed by "TUNER" and then
"AUTO".
™ EASY SET will start searching for all
RDS radio stations with sufficient
signal strength and then followed by
radio stations on FM, MW and LW
band respectively. Weak RDS radio
stations may be stored in later
presets.
™ All available RDS and radio stations
with sufficient signal strength will be
stored. Up to 40 presets may be
stored.
2 The system will proceed to set the RDS
time automatically with the stored RDS
preset station.
FWM55-22-GB-ENG-V01 11
• If no RDS station is available in the first
preset station, the program will exit
automatically.
™ After a radio station is found,
"EASY SET" will be displayed
and followed by "TIME".
• When searching RDS time;
™ "SEARCH RDS TIME" will be
displayed.
™ When RDS time is read, "RDS
TIME" will be displayed. The
current time will be displayed for 2
seconds and stored automatically.
Notes:
– EASY SET will start with the RDS
station, if there are still presets
available, it will continue to store the
FM, MW and LW bands respectively.
– When EASY SET is used, all previously
stored radio stations will be replaced.
– The last preset radio station or the first
available RDS station will appear on the
display when EASY SET is completed.
– If RDS station does not transmit RDS
time within 90 seconds, the program
will exit automatically and the display
will show " NO RDS TIME ".
Switching the system ON
• Press CD, TUNER, TAPE or AUX.
You can also switch on the system by
pressing any one of the DISC DIRECT PLAY
buttons.
Switching the system to
standby mode
• Press STANDBY ON or B on the
remote control.
™ The system will switch to standby
mode.
Selecting the Source
• Press the respective source selection
button: CD, TUNER, TAPE or AUX.
™ The display indicates the selected
source.
Note:
– For an external source, make sure you
have connected the audio left and right
OUT terminals of the external
equipment (TV, VCR, Laser Disc player,
DVD player or CD Recorder) to the AUX/
CDR IN terminals.
12/8/00, 1:57 PM
OPERATING THE SYSTEM
Selecting the Equalizer
Display
You can select the desired equalizer display
for the system. You must not press the DSC
or INCREDIBLE SURROUND button on the
system before using the JOG control.
• Adjust the JOG control to select the
desired Equalizer Display, NORMAL,
TOP DOWN, or NITE MODE.
™ The selected display will be shown.
NORMAL Display
PROGRAM STEREO
REPEAT TIMER REC BACK
FRONT HSD
NEWS T.A. AM MW FM LW
60Hz 250Hz 500Hz 2KHz 4KHz 8KHz
1KHz
TOP DOWN Display
PROGRAM STEREO
BACK
REPEAT TIMER REC
FRONT HSD
NEWS T.A. AM MW FM LW
60Hz 250Hz 500Hz 1KHz 2KHz 4KHz 8KHz
NITE MODE Display
PROGRAM STEREO
REPEAT TIMER REC BACK
FRONT HSD
NEWS T.A. AM MW FM LW
60Hz 8KHz
250Hz 500Hz 1KHz 2KHz 4KHz
Note:
– In NITE MODE, all lights will be
switched off and the display brightness
will be dimmed.
3139 115 20071
11