Important notes for users in the U.K. Mains plug This apparatus is fitted with an approved 13 Amp plug. To change a fuse in this type of plug proceed as follows: Remove fuse cover and fuse. Fix new fuse which should be a BS1362 3 Amp, A.S.T.A.
Contents General Information Supplied accessories ... 5 Environmental information ... 5 Safety information ... 5 Preparation Rear connections ... 6 Optional connection ... 7 Inserting batteries into the remote control ... 7 Controls Controls on the system and remote control ... 8 Basic Functions Switching the system on ...
Congratulations on your purchase and welcome to Philips! To fully benifit from the support that Philips offers, register your product at www.philips.com/welcome. This product complies with the radio interference requirements of the European Union. Supplied accessories – 2 speaker boxes –...
Preparations speaker (right) Rear connections The type plate is located at the back of the system. Power Before connecting the AC power cord to the wall outlet, ensure that all other connections have been made. WARNING! – For optimal performance, use only the original power cable.
Optional connection The optional equipment and connecting cords are not supplied. Refer to the operating instructions of the connected equipment for details. Connecting external equipment Use a cinch cable to connect AUX IN to the analogue audio out terminals of an external equipment (TV, VCR, Laser Disc player, DVD player or CD Recorder).
Controls (illustrations on page 3) Controls on the system and remote control LCD Display – shows the status of the system. iR SENSOR – infrared sensor for remote control. PROGRAM (PROG) for CD ... programs tracks and reviews the program. STANDBY-ON y (POWER y) –...
IMPORTANT: Before you operate the system, complete the preparation procedures. Switching the system on ● Press STANDBY-ON y (POWER y on the remote). ➜ The system will switch to the last selected source. Switching the system to Eco Power Standby mode ●...
CD/MP3 Operation IMPORTANT: The lens of the CD player should never be touched. Playing a disc This CD player plays Audio Discs including CD- Recordables, CD-Rewritables and MP3 CD. ¶ CD-ROM, CD-I, CDV, VCD, DVD or computer CDs, however, are not possible. Adjust the source selector to select CD source.
Supported MP3 disc formats: – ISO9660, Joliet, UDF 1.5 – Maximum title number: 511 (depending on filename length) – Maximum album number: 99 – Supported sampling frequencies: 32 kHz, 44.1 kHz, 48 kHz – Supported Bit-rates: 32~256 (kbps), variable bitrates Different play modes: SHUFFLE and REPEAT You can select and change the various play...
Radio Reception Tuning to radio stations Adjust the source selector to select TU/AUX. Adjust the mode selector to select your desired waveband: MW or FM. ➜ is displayed. Adjust the TUNING control knob to tune to a desired radio frequency. Note: –...
Tape playback Adjust the source selector to select TAPE source. ➜ Display: shows throughout tape TAPE operation. Press STOP•OPENÇç to open the tape door. Insert a recorded tape and close the tape door. ➜ Load the tape with the open side downward and the full spool to the left.
Tape Operation / Recording To select and record a particular passage within a CD track: ● Press and hold down on REW à or F.FWD á. Release the control when you recognize the passage you want. ● To interrupt CD playback press 2; . ●...
Setting the clock In any mode, press CLOCK/TIMER twice. ➜ The clock digits for the hours flash. Press TITILE-/+ ¡1 / 2™ (í/ë on the remote) to set the hours. Press CLOCK/TIMER again. ➜ The clock digits for the minutes flash. Press TITILE-/+ ¡1 / 2™...
Cleaning the disc lens ● After prolonged use, dirt or dust may accumulate at the disc lens. To ensure good playback quality, clean the disc lens with Philips CD Lens Cleaner or any commercially available cleaner. Follow the instructions supplied with cleaner.
WARNING Under no circumstances should you try to repair the system yourself, as this will invalidate the warranty. Do not open the system as there is a risk of electric shock. If a fault occurs, first check the points listed below before taking the system for repair. If you are unable to remedy a problem by following these hints, consult your dealer or service centre.
Troubleshooting The remote control does not function The timer is not working. The Clock/Timer setting is erased. – Reduce the distance between the remote control and the system. – Insert the batteries with their polarities (+/– signs) aligned as indicated. –...