Table of Contents
Advertisement
English
Controls on the system and
remote control
1
BAND
–
for Tuner (on the set only) selects waveband.
2
SOURCE (CD/ TUNER/ AUX)
–
switches on the system.
–
selects the respective sound source for CD/
FM/ AM/ AUX.
3
STANDBY-ON / y
–
switches the system to standby/on.
4
PROG/CLOCK
for CD ................. programs tracks and reviews the
program.
for clock .............. sets the clock function.
5
OPEN•CLOSE
–
opens/closes the CD door.
6
VOLUME – /
+
–
adjusts volume level.
TUNING 0
7
–
tunes to radio stations.
8
iR SENSOR
–
infrared sensor for remote control.
9
n
–
connect headphones.
0
ÉÅ
for CD ................. starts or pauses CD playback.
¡1 / 2™
!
–
skips to the beginning of a current track/
previous/ next track.
–
fast searches back and forward within a track/
CD.
STOP 9
@
–
stops CD playback or erase a CD program.
#
AUX IN
–
connects to external audio source.
$
MUTE
–
switches playback sound off and on.
%
REPEAT
–
repeats a track/disc/ all programmed tracks.
^
SHUFF (SHUFFLE)
–
plays CD/MP3 tracks in random order.
&
SLEEP
–
activates/deactivates or selects the sleeper time.
7
Controls
*
TIMER
–
activates/deactivates or sets the timer function.
(
ALBUM 4 3
for MP3 disc......................selects an album.
)
DBB
–
(Dynamic Bass Boost) enhances the bass.
¡
DSC
–
(Digital Sound Control) selects sound
characteristics: JAZZ/POP/CLASSIC/ROCK.
3
$
MUTE
CD
TUNER
2
4
AUX
PROG
%
^
REPEAT
SHUFF
&
*
SLEEP
TIMER
@
0
ALBUM
(
!
VOLUME
6
)
¡
DBB
DSC
Notes for remote control:
– First select the source you wish to
control by pressing one of the source select
keys on the remote control (for example
CD , TUNER).
– Then select the desired function (for
example É , í , ë ).
General Information
This set complies with the FCC rules,
Part 15 and with 21 CFR 1040.10.
Operation is subject to the following two
conditions:
– This device may not cause harmful
interference, and
– This device must accept any
interference received, including
interference that may cause undesired
operation.
Supplied accessories
– 2 speaker boxes
– remote control with battery
– AM loop antenna
Environmental Information
All unnecessary packaging has been omitted.
We have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet).
Your system consists of materials which can be
recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Safety Information
Before operating the system, check that the
operating voltage indicated on the typeplate (or
the voltage indication beside the voltage
selector) of your system is identical with the
voltage of your local power supply. If not, please
consult your dealer.
Place the system on a flat, hard and stable
surface.
Place the system in a location with adequate
ventilation to prevent internal heat build-up in
your system. Allow at least 10 cm (4 inches)
clearance from the rear and the top of the unit
and 5 cm (2 inches) from each side.
The ventilation should not be impeded by
covering the ventilation openings with items,
such as newspapers, table-cloths, curtains, etc.
Do not expose the system, batteries or discs to
excessive moisture, rain, sand or heat sources
caused by heating equipment or direct sunlight.
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
No objects filled with liquids, such as vases, shall
be placed on the apparatus.
If the system is brought directly from a cold to a
warm location, or is placed in a very damp
room, moisture may condense on the lens of
the disc unit inside the system. Should this occur,
the CD player would not operate normally.
Leave the power on for about one hour with
no disc in the system until normal playback is
possible.
The mechanical parts of the set contain self-
lubricating bearings and must not be oiled or
lubricated.
When the system is switched to Standby
mode, it is still consuming some power.
To disconnect the system from the
power supply completely, remove the
AC power plug from the wall socket.
8
Advertisement
Table of Contents
