Avaya 5600 Series Installation Job Aid
Ethernet routing switch
Hide thumbs
Also See for 5600 Series:
- Regulatory information (83 pages) ,
- Installation and safety instructions (11 pages) ,
- Quick install manual (2 pages)
Advertisement
Quick Links
Installation Job Aid (English) for Avaya
Ethernet Routing Switch 5600 Series
(NN47200-304, ver 01.01)
Before you begin
Ensure the area where you install and use the Avaya ERS 5600 Series switch meets the
following environmental requirements:
• Ambient temperature between 32° and 106° F (0° and 50° C)
• Relative humidity between 10% and 90% noncondensing
• No nearby heat sources such as hot air vents or direct sunlight
• No nearby sources of severe electromagnetic noise
• No excessive dust
• Adequate power source within six feet; one circuit required for each power supply (see
table, AC and DC power specifications)
• At least 2 inches (5.08 cm) on each side of the switch unit for ventilation
• Adequate space at the front and rear of the switch for access to cables
If you are installing a single Avaya Ethernet Routing Switch on a table or shelf, ensure the
surface can support at least 21 to 33 pounds (9.5 to 15 kilograms).
Installing the switch on a table or shelf
You can install a single Avaya Ethernet Routing Switch on any flat surface that can safely
support the weight of the switch and attached cables (21 to 33 pounds or 9.5 to 15
kilograms).
December 2013
1
Advertisement
Related Manuals for Avaya 5600 Series
Summary of Contents for Avaya 5600 Series
- Page 1 Ethernet Routing Switch 5600 Series (NN47200-304, ver 01.01) Before you begin Ensure the area where you install and use the Avaya ERS 5600 Series switch meets the following environmental requirements: • Ambient temperature between 32° and 106° F (0° and 50° C) •...
- Page 2 Installing the switch on a table or shelf The following figures provide instructions for installing the switch on a table or shelf. Attach the rubber feet at the marked locations. December 2013...
- Page 3 Installing the switch on a table or shelf Set the switch on a table or shelf. Note: Allow at least 2 inches (5.1 cm) on each side for proper ventilation and at least 5 inches (12.7 cm) at the back for power cord clearance. December 2013...
-
Page 4: Installing The Switch In An Equipment Rack
Installing the switch in an equipment rack Installing the switch in an equipment rack Required tool: Phillips screwdriver for attaching brackets to the switch. Rack requirements: • A space of 2.8 inches (71.1 centimeters) for each switch in an EIA or IEC standard 19 inch (48.2 centimeter) equipment rack and TIA 23 inch (58.5 centimeter) equipment rack. - Page 5 Installing the switch in an equipment rack Figure 1: Front-mounted rack bracket installation Attach a bracket to each side of the switch. December 2013...
- Page 6 Installing the switch in an equipment rack Figure 2: Front-mounted rack installation Slide the switch into the rack. Insert and tighten the rack mount screws. December 2013...
- Page 7 Installing the switch in an equipment rack Figure 3: Rear-mounted rack bracket installation Attach a bracket to each side of the switch. December 2013...
-
Page 8: Ac And Dc Power Specifications
Figure 4: Rear-mounted rack installation Slide the switch into the rack. Insert and tighten the rack mount screws. AC and DC power specifications The following table describes the AC and DC power specifications for the Ethernet Routing Switch 5600 Series. December 2013... - Page 9 AC and DC power specifications Input current Amps maximum Power Thermal Power Power per power supply consum rating supply over ption used Ethernet (PoE) Model 100–120 48 VDC 200–240 Watts BTU/h Watts Power maximu maximu AC/DC, per port DC/DC (Watts) 5632FD 5632FD 5650TD...
-
Page 10: Connecting Ac Power
Connecting AC power Input current Amps maximum Power Thermal Power Power per power supply consum rating supply over ption used Ethernet (PoE) Model 100–120 48 VDC 200–240 Watts BTU/h Watts Power maximu maximu AC/DC, per port DC/DC (Watts) 1365 1000 5698TFD- PWR DC 21 *... - Page 11 50 Hz Single phase The Ethernet Routing Switch 5600 Series does not have a power switch. When you connect the AC power cord to a suitable AC power outlet, the switch powers up immediately. Connect the AC power cord to the back of the switch, and then connect the cord to a power outlet.
-
Page 12: Safety Messages
Safety messages Figure 5: Connecting the AC power cord to the Ethernet Routing Switch 5600 Series Safety messages December 2013... - Page 13 Safety messages Warning: Installation must be performed by qualified service personnel only. Read and follow all warning notices and instructions marked on the product or included in the documentation. Voltage: This equipment relies on the building's installation for overcurrent protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 15 A U.S.
- Page 14 Safety messages Caution: Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. December 2013...