Bosch Uneo Maxx Original Instructions Manual page 7

A)
(10) Battery
(11) "PowerLight"
A)
(12) Universal bit holder
A)
(13) Screwdriver bit
(14) Screwdriver bit with ball catch
(15) Drill bit with hexagonal shank
(16) Drill bit with SDS-Quick tool holder
(17) Handle (insulated gripping surface)
(18) Battery release button
A)
(19) Keyless chuck
(20) Front sleeve of the keyless chuck
(21) Rear sleeve of the keyless chuck
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.
Technical data
Cordless rotary hammer
Article number
Rated voltage
Rated speed
Impact rate
Impact energy per stroke ac-
cording to EPTA-Procedure
05:2016
Tool holder
Max. drilling diameter
– Concrete (with twist drill
bit)
– Steel
– Wood
– Wood (with flat milling
drill)
Weight according to EPTA-
Procedure 01:2014
Permitted ambient temperature
– during charging
A)
– During operation and
during storage
Recommended batteries
Recommended chargers
– PBA 18V....V-.
– PBA 18V....W-.
A) Limited performance at temperatures < 0 °C
Technical data determined using the battery that comes with the
product.
Bosch Power Tools
Fitting
Before any work on the tool (e.g. maintenance, tool
u
change etc.) as well as during transport and storage,
set the rotational direction switch to the middle posi-
tion. There is risk of injury from unintentionally pressing
A)
the on/off switch.
A)
A)
Charging the battery (see figure A)
Use only the chargers listed in the technical data. Only
u
these chargers are matched to the lithium-ion battery of
your power tool.
Note: The battery is supplied partially charged. To ensure
A)
full battery capacity, fully charge the battery in the charger
A)
before using your power tool for the first time.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The lithium-ion battery is protected against deep discharge
by the "Electronic Cell Protection (ECP)". When the battery
Uneo Maxx
is discharged, the power tool is switched off by means of a
protective circuit: The application tool no longer rotates.
3 603 J52 3..
Do not continue to press the On/Off switch after the
u
V= 18
power tool has automatically switched off. The battery
rpm 0−900
can be damaged.
rpm 0−5000
– To remove the battery (10), press the release button
(18) and pull the battery to the rear and out of the power
J 0.6
tool. Do not use force to do this.
Follow the instructions on correct disposal.
SDS-Quick
Selecting drill chucks and tools
Hexagonal
An SDS-Quick application tool is required for hammer
drilling.
mm 10
To drill without impact in wood, metal, ceramic and plastic,
you can use a suitable SDS-Quick application tool, a hex
shank application tool or the keyless chuck with application
mm 8
tools that do not have SDS-Quick.
mm 10
For screwdriving, only use screwdriver bits which have a ball
mm 20
catch (14) (DIN 3126-E6.3). Other screwdriver bits (13)
can be inserted using a universal bit holder with ball catch
kg 1.4
(12).
You will find a selection of suitable application tools in the
accessories overview at the end of these operating instruc-
tions.
°C 0 to +45
°C -20 to +50
Changing the Keyless Chuck
You must use the keyless chuck (19) to work with applica-
PBA 18V....V-.
tion tools that do not have SDS-Quick (e.g. cylindrical shank
drill bits).
PBA 18V....W-.
Inserting the keyless chuck (see figure B)
– Clean and lightly grease the insertion end of the shank.
AL 22.. CV
AL 18.. CV
– Insert the keyless chuck (19) with the shank into the tool
holder while turning it until it locks automatically.
AL 18.. CV
– Check that it is locked by pulling the keyless chuck.
English | 7
1 609 92A 4KJ | (25.07.2018)