Cisco 800M Series Installing Manual
  1. Manuals
  2. Brands
  3. Cisco Manuals
  4. Network Router
  5. Profile Series
  6. Installing manual
Cisco 800M Series Installing Manual

Cisco 800M Series Installing Manual

Hide thumbs Also See for 800M Series:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Configuration Manual, User Manual
Installing the Router
This chapter describes the equipment and the procedures for successfully installing the Cisco 800M
Series ISR, and contains the following sections:
Equipment, Tools, and Connections, page 2-2
•
•
Installing the Router, page 2-3
•
Mounting the DC Power Supply, page 2-14
Note
For compliance and safety information, see
800 Series
Routers.
Warning
Read the installation instructions before connecting the system to the power source. Statement 1004
Warning
This equipment must be grounded. Never defeat the ground conductor or operate the equipment in the
absence of a suitably installed ground conductor. Contact the appropriate electrical inspection
authority or an electrician if you are uncertain that suitable grounding is available. Statement 1024
Only trained and qualified personnel should be allowed to install, replace, or service this equipment.
Warning
Statement 1030
No user-serviceable parts inside. Do not open. Statement 1073
Warning
Ultimate disposal of this product should be handled according to all national laws and regulations.
Warning
Statement 1040
Warning
Read the wall-mounting instructions carefully before beginning installation. Failure to use the
correct hardware or to follow the correct procedures could result in a hazardous situation to people
and damage to the system. Statement 378
C H A P T E R
Regulatory Compliance and Safety Information for Cisco
Cisco 800M Series Integrated Services Router Hardware Installation Guide
2
2-1

Advertisement

Table of Contents
loading

Related Manuals for Cisco 800M Series

Summary of Contents for Cisco 800M Series

  • Page 1 C H A P T E R Installing the Router This chapter describes the equipment and the procedures for successfully installing the Cisco 800M Series ISR, and contains the following sections: Equipment, Tools, and Connections, page 2-2 • • Installing the Router, page 2-3 •...

  • Page 2: Chapter

    Ethernet Devices, page 2-2 • Items Shipped with your Router Unpack the box and verify that all items listed on the invoice are shipped with the Cisco 800M Series ISR.The following items are shipped with your router: • PWR CABLE - Country specific Power Cable, Max 1 •...

  • Page 3: Table Of Contents

    Installing the Router This section describes how to install the Cisco 800M Series ISR. The Cisco 800M Series ISR can be installed on a table top or mounted on a wall. You can choose the type of mounting while ordering the Cisco 800M Series ISR.

  • Page 4: Warnings

    Figure 2-2. Step 2 Orient the Cisco 800M Series router, facing the I/O side facing upwards as shown in Figure 2-2, or in the opposite direction such that the I/O side is facing downwards as shown in Figure 2-3.

  • Page 5: Installing The Router

    Install the router to a wall stud using two number-10 wood screws, and round- or pan-head. The screws Step 3 must be long enough to penetrate at least 1.0 inch (25.4 mm) into the supporting wood or metal wall stud as shown in Figure 2-4. Cisco 800M Series Integrated Services Router Hardware Installation Guide...

  • Page 6: Installing The Router

    The two brackets provided along with the router which can be used for wall mount or rack mount. These brackets support mounted the router on a standard 19 inch rack. The brackets must be rotated 90 degrees and used for mounting it on the rack. Cisco 800M Series Integrated Services Router Hardware Installation Guide...

  • Page 7: Installing The Router

    Router I/O facing the user - Reverse the rack mount brackets to have offset rack mount option as shown in Figure 2-7. Figure 2-5 Attaching the Brackets (LEDs facing the user) LEDs facing the user Figure 2-6 Attaching the Brackets(I/O side facing the user) Input/ Output side Cisco 800M Series Integrated Services Router Hardware Installation Guide...

  • Page 8: Installing The Modules

    Mount the router into the rack using the screws provided in the rack. Step 2 Installing the modules You can choose either slot 0 or slot 1 for inserting modules. Combination of modules supported by Cisco 800M Series ISR is as follows: • One 3G module and one serial port module. •...

  • Page 9: Accessing The Sim Card

    Installing the Router Figure 2-8 Removing the blank covers Step 3 Insert the 3G module or serial port module using the captive screws such that the Cisco logo of the module is facing the user as shown in Figure 2-9.

  • Page 10: Installing Antennas

    Installing Antennas Note Before you install the Cisco 800M Series ISR on a table, wall or rack, install the antennas on the front panel. It is difficult to install the antennas after the router is installed. To attach the antennas to your router, follow these steps: Remove the two rubber caps from the 3G Module.

  • Page 11: Installing The Router Ground Connection

    Attach the ring terminal to the chassis. Use the single screw provided. Tighten the screws to a torque of Step 4 8 to 10 inch-pound (0.9 to 1.1 newton meter) as shown in Figure 2-12. Cisco 800M Series Integrated Services Router Hardware Installation Guide 2-11...

  • Page 12: Installing The Power Cord Retention Latch

    Installing the Power Cord Retention Latch The Cisco 800M Series ISR has a power cord retention mechanism as a accessory. It locks the power cord to the router. When a user accidentally pulls on the power cord, the power cord will not come out from the router.

  • Page 13: Installing The Router

    To remove the power cord lock, use your thumb and index fingers to squeeze ends of tabs while pulling Step 3 away from the router as shown in Figure 2-15. Figure 2-15 End of Tabs Cisco 800M Series Integrated Services Router Hardware Installation Guide 2-13...

  • Page 14: Mounting The Dc Power Supply

    Statement 378 The Cisco 800M ISR DC power supply may be mounted to a wall using four #6 pan- or round-head wood screws for the mounting holes on the supply.

  • Page 15: Installing The Router

    The DC supply is IP 41 compliant in all six orthogonal directions. The mounting orientation will not affect IP 41 compliance. Step 3 Connect the chassis to a reliable earth ground. Cisco 800M Series Integrated Services Router Hardware Installation Guide 2-15...

  • Page 16: Installing The Router

    Chapter 2 Installing the Router Cisco 800M Series Integrated Services Router Hardware Installation Guide 2-16...

Table of Contents