H3C WX3500H Series Installation Manual
Hide thumbs
Also See for WX3500H Series:
- User configuration manual (57 pages) ,
- Installations (4 pages)
Related Manuals for H3C WX3500H Series
Summary of Contents for H3C WX3500H Series
- Page 1 H3C WX3500H Series Access Controllers Installation Guide New H3C Technologies Co., Ltd. http://www.h3c.com.hk Document version: 6W103-20170519...
- Page 2 , H3CS, H3CIE, H3CNE, Aolynk, Care, , IRF, NetPilot, Netflow, SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New H3C Technologies Co., Ltd. All other trademarks that may be mentioned in this manual are the property of their respective owners Notice The information in this document is subject to change without notice.
- Page 3 Preface This installation guide describes the procedures for installing, accessing, troubleshooting, and maintaining the WX3500H access controllers. This preface includes the following topics about the documentation: • Audience. • Conventions • Obtaining documentation • Technical support • Documentation feedback Audience This documentation is intended for: •...
- Page 4 Convention Description Multi-level menus are separated by angle brackets. For example, File > Create > > Folder. Symbols Convention Description An alert that calls attention to important information that if not understood or followed WARNING! can result in personal injury. An alert that calls attention to important information that if not understood or followed CAUTION: can result in data loss, data corruption, or damage to hardware or software.
- Page 5 Obtaining documentation To access the most up-to-date H3C product documentation, go to the H3C website at http://www.h3c.com.hk To obtain information about installation, configuration, and maintenance, click http://www.h3c.com.hk/Technical_Documents...
-
Page 6: Table Of Contents
Contents Preparing for installation ···································································· 1 Safety recommendations ············································································································· 1 Safety symbols ··················································································································· 1 General safety recommendations ··························································································· 1 Electrical safety ··················································································································· 1 Laser safety ······················································································································· 2 Examining the installation site ······································································································· 2 Temperature and humidity ····································································································· 2 Cleanliness ························································································································ 2 Cooling ·····························································································································... - Page 7 Restrictions and guidelines ·································································································· 28 Configuration procedure ····································································································· 29 Appendix A Chassis views and technical specifications ·························· 30 Chassis views ························································································································· 30 WX3508H ························································································································ 30 WX3510H ························································································································ 30 WX3520H ························································································································ 31 WX3540H ························································································································ 32 Power module views ················································································································· 32 AC power module ·············································································································· 32 DC power module ··············································································································...
-
Page 8: Preparing For Installation
Preparing for installation H3C WX3500H access controllers include the following models: • WX3508H. • WX3510H. • WX3520H. • WX3540H. Safety recommendations To avoid any equipment damage or bodily injury, read the following safety recommendations before installation. Note that the recommendations do not cover every possible hazardous condition. -
Page 9: Laser Safety
• Locate the emergency power-off switch in the room before installation. Shut off the power immediately if an accident occurs. • Unplug all the external cables (including power cords) before moving the chassis. • Do not work alone when you operate the device with the device powered on. •... -
Page 10: Cooling
Table 2 Dust concentration limit in the equipment room Substance Concentration limit (particles/m ≤ 3 x 10 Dust particles (No visible dust on desk in three days) NOTE: Dust particle diameter ≥ 5 µm To eliminate corrosion and premature aging of components, the equipment room must also meet limits on salts, acids, and sulfides, as shown in Table Table 3 Harmful gas limits in an equipment room... -
Page 11: Emi
• Maintain the humidity and temperature at acceptable levels. For more information, see "Temperature and humidity." • Before working with the device, wear an ESD wrist strap or gloves and ESD garment, and remove conductive objects such as jewelry or watch. Make sure the wrist strap makes good skin contact and is reliably grounded. -
Page 12: Lightning Protection
• Keep the device far away from radio transmitting stations, radar stations, and high-frequency devices. • Use electromagnetic shielding, for example, shielded interface cables, when necessary. • To prevent signal ports from getting damaged by overvoltage or overcurrent caused by lightning strikes, route interface cables only indoors. -
Page 13: Installation Tools
Accessory WX3508H WX3510H WX3520H WX3540H Front mounting bracket × 2 × × × 2 Installation tools No installation tools are provided with the device. Prepare installation tools as required. Figure 3 Installation tools Flathead screwdriver Phillips screwdriver Needle-nose pliers Wire-stripping pliers Diagonal pliers Mark ESD wrist strap... - Page 14 Item Requirements Result • Effective measures are taken for filtering interference from the power grid. • The protection ground of the device is away from the grounding facility of power equipment or lightning protection grounding facility. EMI prevention • The device is far away from radio transmitting stations, radar stations, and high-frequency devices.
-
Page 15: Installing The Device
WARNING! Keep the tamper-proof seal on a mounting screw on the chassis cover intact, and if you want to open the chassis, contact H3C Support for permission. Otherwise, H3C will not be liable for any consequence caused thereby. Confirming installation preparations Before you install the device, verify that you have read "Preparing for... -
Page 16: Installation Flow
Installation flow Figure 4 Installation flow Mounting the device on a workbench CAUTION: Do not place heavy objects on the device. If a standard 19-inch rack is not available, you can mount the device on a clean, flat workbench. To mount the device on a workbench:... -
Page 17: Installing The Device In A 19-Inch Rack
Place the device upside down. Clean the recessed areas on the chassis bottom. Attach the four rubber feet to the recessed areas on the chassis bottom. Place the device on the workbench with the upside up. Make sure the four rubber feet stand firmly on the workbench. - Page 18 b. Use a mounting bracket to mark cage nut installation positions on the two front rack posts. c. Install cage nuts into the marked square holes on the front rack posts. Figure 6 Installing cage nuts Use the screws supplied with the mounting brackets to secure the mounting brackets to both sides of the device.
-
Page 19: Grounding The Device
Figure 8 Installing the device in the rack (WX3508H) Grounding the device WARNING! • Correctly connecting the grounding cable is crucial to lightning protection and EMI protection. • Connect the grounding cable to the grounding system in the equipment room. Do not connect it to a fire main or lightning rod. - Page 20 Figure 9 Grounding the device with a grounding strip (WX3508H) Grounding the device with the rack—Connect the other end of the grounding cable to the grounding point on the rack and make sure the rack has been reliably grounded. Figure 10 Grounding the device with the rack (WX3508H)
-
Page 21: (Optional) Installing Network Port Lightning Protectors
Grounding the device with a grounding conductor buried in the earth—If earth is available at the installation site, hammer a 0.5 m (1.64 ft) or longer angle iron or steel tube into the earth to serve as a grounding conductor. Weld the yellow-green grounding cable to the angel iron or steel tube and treat the joint for corrosion protection. -
Page 22: (Optional) Installing A Surge Protected Power Strip
Figure 12 Installing a lightning protector for a network port (WX3540H) (Optional) Installing a surge protected power strip IMPORTANT: Before installing a surge protected power strip, read the instructions in the document that comes with the strip. If you use an AC power line routed from outdoors for the device, use a surge protected power strip for the device to protect against damages caused by lightning strikes. -
Page 23: Connecting Ethernet Cables
• Stop bits—1. • Parity—None. • Flow control—None. Connecting Ethernet cables Connecting a copper Ethernet port Connect one end of the Ethernet cable to the copper Ethernet port of the device, and the other end to the Ethernet port of the peer device. After powering on the device, examine the LEDs of the fixed copper Ethernet port. -
Page 24: Installing A Power Module
Figure 13 Connecting an optical fiber (WX3508H) Installing a power module CAUTION: Do not install an AC power module and a DC power module on the same device. To install a power module: Remove the blank filler panel (if any) from the slot where you want to install a power module with a Phillips screwdriver. -
Page 25: Connecting An Ac Power Cord
Figure 15 Installing a DC power module (WX3540H) Connecting an AC power cord CAUTION: Before powering on the device, connect the grounding cable of the device. To connect an AC power cord: Pivot the bail latch leftwards. Connect one end of the AC power cord to the AC-input power receptacle on the device. Pivot the bail latch rightwards to secure the power cord. -
Page 26: Verifying The Installation
Press Ctrl+T to start heavy memory test Booting Normal Extended BootWare The Extended BootWare is self-decompressing..Done. **************************************************************************** H3C WX3510H BootWare, Version 5.09 **************************************************************************** Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. Compiled Date : Apr 21 2017 CPU Type : 1000MHz Multi-core Processor Memory Type... - Page 27 cfa0 Size : 4002MB CPLD1 Version : 004 CPLD2 Version : 000 PCB Version : Ver.A BootWare Validating... Press Ctrl+B to access EXTENDED-BOOTWARE MENU... Press Ctrl + B at the prompt within 4 seconds to access the Boot menu. To access the Boot menu after the system enters the system image file reading and self-compressing process, restart the device.
- Page 28 Cryptographic Algorithms Known-Answer Tests passed. Line con0 is available. Press ENTER to get started. Press Enter at the prompt, and you can configure the device when the prompt <H3C> appears. During the startup process, the CPLD is automatically upgraded to the latest version.
-
Page 29: Troubleshooting
Verify that the power source is as required. Verify that the power cord is connected securely. Verify that the power cord is in good condition. If the issue persists, contact H3C Support. No display or garbled display on the configuration terminal... -
Page 30: Software Loading Failure
When you use TFTP to load software, you entered an incorrect IP address, software name, or TFTP serve path. When you use FTP to load software, you entered an incorrect IP address, software name, username, or password. If the issue persists, contact H3C Support. -
Page 31: Hardware Management And Maintenance
H3C Comware Software, Version 7.1.064, Release 5323 Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. All rights reserved. H3C WX3510H uptime is 0 weeks, 0 days, 18 hours, 28 minutes Last reboot reason : User soft reboot Boot image: cfa0:/boot.bin Boot image version: 7.1.064, Release 5323... - Page 32 H3C Comware Software, Version 7.1.064, Release 5323 Copyright (c) 2004-2017 New H3C Technologies Co., Ltd. All rights reserved. H3C WX3510H uptime is 0 weeks, 0 days, 18 hours, 28 minutes Last reboot reason : User soft reboot Boot image: cfa0:/boot.bin Boot image version: 7.1.064, Release 5323...
-
Page 33: Displaying Information About The Device
An electronic label is a profile of a device. It contains the permanent configuration, including the serial number, manufacturing date, MAC address, and vendor name. Use the display device manuinfo command to display the electronic label data for the device. <H3C>display device manuinfo Slot 1 CPU 0: DEVICE_NAME:WX3510H... -
Page 34: Displaying The Memory Usage Of The Device
CPU usage at the interval of 5 minutes). Displaying the memory usage of the device Use the display memory command to display the memory usage statistics for the device. <H3C>display memory Memory statistics are measured in KB: Slot 1:... -
Page 35: Displaying The Operating State Of Power Modules
Before you reboot the device, perform the following tasks: Use the save command to save the running configuration. For more information about the save command, see configuration file management commands in H3C WX3500H Access Controller Fundamentals Command Reference. Use the display startup and display boot-loader commands to verify that you have specified the correct next-startup configuration files and startup software images. -
Page 36: Configuration Procedure
For more information about the display startup and display boot-loader commands, see software upgrade commands in H3C WX3500H Access Controller Fundamentals Command Reference. • The device will not reboot if a file is being accessed. -
Page 37: Appendix A Chassis Views And Technical Specifications
Appendix A Chassis views and technical specifications Chassis views WX3508H Figure 18 Front panel (1) 100/1000BASE-T autosensing Ethernet copper ports 1 through 6 (2) 100/1000BASE-T autosensing Ethernet copper ports 7 and 8 (combo interfaces) (3) 1000BASE-X SFP ports 7 and 8 (combo interfaces) (4) USB port (5) SD card slot (6) Console port... -
Page 38: Wx3520H
Figure 21 Rear panel (1) Power module slot 1 (PWR1) (2) Power module slot 2 (PWR2) (3) Expansion slot (4) Grounding screw WX3520H Figure 22 Front panel (1) 100/1000BASE-T autosensing Ethernet copper ports 1 through 8 (combo interfaces) (2) 100BASE-FX/1000BASE-X SFP ports 1 through 8 (combo interfaces) (3) 10GBASE-R SFP+ ports 9 and 10 (4) Console port Figure 23 Rear panel... -
Page 39: Wx3540H
WX3540H Figure 24 Front panel (1) 100/1000BASE-T autosensing Ethernet copper ports 1 through 8 (combo interfaces) (2) 100BASE-FX/1000BASE-X SFP ports 1 through 8 (combo interfaces) (3) 10GBASE-R SFP+ ports 9 and 10 (4) 100/1000BASE-T management Ethernet port (5) Console port Figure 25 Rear panel (1) Power module slot 1 (PWR1) (2) Power module slot 2 (PWR2) -
Page 40: Dc Power Module
DC power module Figure 27 DC power module (1) Captive screw (2) Power receptacle Interface numbering A combo interface is a logical interface that contains a fiber port and a copper port. Only one port is activated at a time. By default, the copper port is activated. WX3508H Fixed ports on a WX3508H access controller are numbered as follows: •... -
Page 41: Technical Specifications
Technical specifications WX3508H Table 13 WX3508H technical specifications Item Specification Console port One, 9600 bps (default) to 115200 bps Gigabit Ethernet port 8 × 100/1000BASE-T autosensing Ethernet copper port 2 × 1000BASE-X SFP port. Each form a combo interface with SFP port the 100/1000BASE-T autosensing Ethernet port marked with the same number. -
Page 42: Wx3520H
WX3520H Table 15 WX3520H technical specifications Item Specification Console port One, 9600 bps (default) to 115200 bps Gigabit Ethernet port 8 × 100/1000BASE-T autosensing Ethernet copper port SFP port 8 × 100BASE-FX/1000BASE-X SFP port SFP+ port 2 × 10GBASE-R SFP+ port Memory 1 ×... -
Page 43: Ac Power Module
AC power module Table 17 AC power module specifications Item Specification Model PSR150-A1 Rated input voltage range 100 VAC to 240 VAC @ 50/60 Hz Rated power capacity 150 W DC power module Table 18 DC power module specifications Item Specifications Model PSR150-D1... -
Page 44: Transceiver Module Specifications
Figure 29 SFP+ transceiver module Figure 30 Optical fiber with LC connectors (1) LC connector (2) Optical fiber Transceiver module specifications The transceiver modules whose names contain MM and SM support multi-mode optical fibers and single-mode optical fibers, respectively. Table 19 Transceiver modules available for the access controllers Device model Available transceiver modules •... - Page 45 Table 20 SFP-FE-SX-MM1310-A specifications Item Specification Central wavelength 1310 nm Transmission distance 2 km (1.24 miles) Transmission rate 125 Mbps Connector type Duplex LC Fiber mode Fiber diameter 50 µm Transmit power –19 to –14 dBm Receive sensitivity ≤ –30 dBm Saturation ≤...
- Page 46 Table 23 SFP-GE-SX-MM850-A specifications Item Specification Central wavelength 850 nm Transmission distance 550 m (1804.46 ft) Transmission rate 1250 Mbps Connector type Duplex LC Fiber mode Fiber diameter 50 µm Transmit power –9.5 to 0 dBm Receive sensitivity ≤ –17 dBm Saturation ≤...
- Page 47 Table 26 SFP-GE-LH40-SM1550 specifications Item Specification Central wavelength 1550 nm Transmission distance 40 km (24.86 miles) Transmission rate 1250 Mbps Connector type Duplex LC Fiber mode Fiber diameter 9 µm Transmit power –4 to +1 dBm Receive sensitivity ≤ –21 dBm Saturation ≤...
- Page 48 Table 29 SFP-XG-LX220-MM1310 specifications Item Specification Central wavelength 1310 nm Transmission distance 220 m (721.78 ft) Transmission rate 10.3125 Gbps Connector type Duplex LC Fiber mode Fiber diameter 62.5 µm Transmit power –6.5 to +0.5 dBm Receive sensitivity ≤ –6.5 dBm Saturation ≤...
-
Page 49: Appendix B Leds
Appendix B LEDs LEDs Figure 31 WX3508H LEDs (1) 100/1000BASE-T autosensing Ethernet copper port status LEDs (2) 1000BASE-X SFP port status LEDs (3) System status LED (SYS) Figure 32 WX3510H LEDs (1) 100/1000BASE-T autosensing Ethernet copper port status LEDs (2) 100BASE-FX/1000BASE-X SFP port status LEDs (3) Power module 1 status LED (PWR1) (4) Power module 2 status LED (PWR2) (5) System status LED (SYS) - Page 50 Figure 33 WX3520H LEDs (1) 100/1000BASE-T autosensing Ethernet copper port status LEDs (2) 100BASE-FX/1000BASE-X SFP port status LEDs (3) 10GBASE-R SFP+ port status LEDs (4) Power module 1 status LED (PWR1) (5) Power module 2 status LED (PWR2) (6) System status LED (SYS) (7) Expansion card status LED (MOD) Figure 34 WX3540H LEDs (1) 100/1000BASE-T autosensing Ethernet copper port status LEDs...
-
Page 51: Led Description
LED description Table 32 LED description for the WX3508H access controller Mark Status Description Flashing green (0.5 Hz) The system is operating correctly. Flashing green (4 Hz) The system is starting up. The system has failed POST, or a critical fault System status LED Steady red has been detected. - Page 52 Mark Status Description 100/1000BASE-T No link is present. out-of-band LINK/ Steady green A link is present. management Ethernet port status Flashing green The port is receiving or transmitting data. Steady yellow A 100 Mbps link is present on the port. The port is receiving or transmitting data at 100 Flashing yellow Mbps.
-
Page 53: Index
Index electronic label data display (on switching engine), fiber port connection, installation, grounding, installation flow, information display (on controller engine), power cord connection, information display (on switching engine), troubleshooting power supply failure, installation verification, Appendix A (Chassis views and technical management and maintenance, specifications), memory usage display,... - Page 54 site cleanliness, cooling requirements, site cooling requirements, device in rack, site dust concentration, EMI prevention, site gas saturation, ESD prevention, site humidity, installation verification, site temperature, lightning protection, ESD prevention, site cleanliness, Ethernet copper port connection, site examination, examining installation site, site humidity, site temperature, fiber...
- Page 55 power cooling requirements, electrical safety recommendations, power module EMI prevention, views, ESD prevention, power supply general recommendations, AC power cord connection, installation site cleanliness, DC power cord connection, installation site dust concentration, operating state display, installation site gas saturation, troubleshooting failure, installation site humidity, preparing for installation, installation site temperature,...
- Page 56 software loading failure, ventilation (installation site), verifying installation, workbench device mount,...