To Memorize Channels; Automatic Channel Memory; To Add/Delete Channels; Adjusting The Picture - Toshiba 13A26C Owner's Manual

TO MEMORIZE CHANNELS

This TV is equipped with a channel memory feature that allows the
TV to skip up or down to the next channel in the TV's memory,
skipping over unwanted channels.
Before selecting channels, you must program them into the TV's
memory. In addition to normal VHF and UHF channels, this TV can
receive up to 113 Cable TV channels. To use this TV with an
antenna, set the TV/CABLE menu option to the TV setting. When
shipped from the factory, this menu option is in the CABLE setting.
TV/CABLE SELECTION
1
Press MENU.
2
Press SET + or – until the indicator next to
"CH SETUP" begins to flash, then press
ENTER.
3
Press SET + or – until the indicator next
to "TV/CABLE" begins to flash.
4
Press ENTER to select the TV or CABLE
mode. The arrow indicates the selected
mode.
5
Repeatedly press MENU until the
menu screen closes.
NOTE:
Contact your cable company to determine the type of cable
system used in your area.

AUTOMATIC CHANNEL MEMORY

1
Press MENU.
2 Press SET + or – until the indicator next to
"CH SETUP" begins to flash, then press
ENTER.
3
Press SET + or – until the indicator next
to "AUTO CH MEMORY" begins to flash,
then press ENTER. The TV will begin
memorizing all the channels available in
your area. Channel numbers will remain
red until auto memorizing is complete.
4
Repeatedly press MENU until the menu screen closes.

ADJUSTING THE PICTURE

You can adjust the settings for brightness, contrast, color,
tint and sharpness.
1 Press MENU.
2 Press SET + or – until the indicator next to "PICTURE"
begins to flash, then press ENTER.
3
Repeatedly press ENTER to select the item you want to
adjust.
BRIGHTNESS CONTRAST
3X00221A(E)_P08-12
MENU
CH SETUP
PICTURE
LANGUAGE
LOCK
ON TIMER
+ / Ð / ENTER / MENU
〈 〉
TV CABLE
AUTO CH MEMORY
ADD / DELETE
〈 + / – / ENTER / MENU 〉
MENU
CH SETUP
PICTURE
LANGUAGE
LOCK
ON TIMER
+ / Ð / ENTER / MENU
〈 〉
TV CABLE
AUTO CH MEMORY
ADD / DELETE
〈 + / – / ENTER / MENU 〉
COLOR TINT SHARPNESS
9

TO ADD/DELETE CHANNELS

1
Press MENU.
2
Press SET + or – until the indicator next to
"CH SETUP" begins to flash, then press
ENTER.
3
Press SET + or – until the indicator
next to "ADD/DELETE" begins to
flash, then press ENTER.
4 Select the desired channels to be
added or deleted using the Direct
Channel Selection buttons (0–9),
CH + or –, SET + or –.
5
Press ENTER to select ADD or DELETE.
If an unmemorized channel was selected (step 4), the
channel indication will be red. Press ENTER if you wish
to ADD the unmemorized channel. The channel
indicator will change from red to green when a channel
is added and the channel will be memorized.
If a memorized channel was selected (step 4), the
channel indication will be green. To delete the channel
from memory, press ENTER repeatedly
until "DEL" appears on-screen. The
channel indicator will change from
green to red when a channel is deleted.
Repeat steps 4 and 5 for each channel
to be added or deleted.
6
Repeatedly press MENU until the menu screen closes.
4
Press SET + or – to adjust the setting.
+
BRIGHTNESS higher
CONTRAST lighter
COLOR deeper
TINT greenish
SHARPNESS sharper
TO RETURN TO FACTORY SETTINGS:
Press RESET while the picture adjusting mode is
on-screen.
22/12/05, 4:41 PM
MENU
CH SETUP
PICTURE
LANGUAGE
LOCK
ON TIMER
+ / Ð / ENTER / MENU
〈 〉
TV CABLE
AUTO CH MEMORY
ADD / DELETE
〈 + / – / ENTER / MENU 〉
ADD CH 012
〈 0 – 9 / + / – / ENTER / MENU 〉
–
lower
darker
paler
reddish
softer
9