Table of Contents
Advertisement
In normal operation, at full rate, after 15 min-
utes the following flame appearance should be
observed:
Rear Burner Flame Characteristics – The
rear flames should be yellow. The flames
should extend about 3 – 4" above the center
log (front of the unitized log group) for natu-
ral gas and 2 – 3" above for propane (L.P.G.)
gas ( Figure 20 ).
Figure 20
Main Burner – The flames at the front burner
holes will be blue becoming yellowish as they
hit the bark-like texture of the base and front
face of the center log (front of the unitized
group) ( Figure 20 ).
Appliance Operation
WARNING: THE LOWER CONTROL COM-
PARTMENT AREA AND LOWER CONTROL
COMPARTMENT ACCESS DOOR ARE EX-
TREMELY HOT WHEN THE APPLIANCE IS
IN OPERATION. EXERCISE EXTREME CARE
WHEN ACCESSING THIS AREA. TOUCH
ONLY THE FAR ENDS OF THE LOWER
CONTROL COMPARTMENT DOOR WHEN
OPENING WHILE THE APPLIANCE IS HOT.
Step 14. Checking the System – With gas line
installed run initial system checkout before
closing up the front of the unit. Follow the pilot
lighting instructions on page 16.
Note: Instructions are also found on the pull
out panel located on the bottom surface of the
appliance.
When first lighting the appliance, it will take a
few minutes for the line to purge itself of air.
Once purging is complete, the pilot and burner
will light and operate as indicated in the instruc-
tion manual. Subsequent lightings of the appli-
ance will not require such purging. Inspect the
pilot flame (remove logs, if necessary, handling
carefully).
10
The pilot flame should be steady, not lifting or
floating. Flame should be blue in color with
traces of orange at the outer edge.
The top 3/8" (10 mm) at the pilot generator
(thermopile) should be engulfed in the pilot
flame (NG only).
Replace logs if removed for pilot inspection.
To light the burner; turn "ON" the optional
remote wall switch (if installed) and rotate the
gas valve control knob counterclockwise to the
"ON" position.
Step 15. Installing the Optional Screen As-
sembly – Retrieve the screen door frame. Po-
sition the door frame in front of the firebox
opening in the brackets at the base of the
fireplace front opening. Lean the door frame
back towards the fireplace ensuring that the
frame seats evenly as it draws shut.
Installing the Optional Glass Door
Position the door frame in front of the firebox
opening, with the joint in the gasket down.
Locate the three (3) tabs at the bottom edge of
the door frame into the three (3) brackets at the
base of the fireplace front opening. Lean the
door frame back towards the fireplace ensuring
that the frame seats evenly as it draws shut.
Install the three (3) 1/4"-20 x 1" Phillips pan
head screws removed previously and tighten to
secure. Ensure that the tab on the bottom of the
door frame engages the door switch.
Make sure the screws are tightened equally to
avoid torquing the door ( Figure 21 ).
Screws
Figure 21
NOTE: DIAGRAMS & ILLUSTRATION NOT TO SCALE.
OPTIONAL EQUIPMENT
An incomparable package of options are avail-
able for use with these appliances. These op-
tions can both customize the operation of these
unique appliances and enhance their beauty
and charming appeal. All options are available
in kit form, are easy to install and are packaged
complete with all required parts and instruc-
tions. Some of the option kits need to be fitted
prior to completing the installation of the appli-
ance. The following paragraphs detail the kit
options available for use with the appliances
covered in this manual.
These outstanding optional items can be added
individually or in sets of two or more to custom-
ize your vent-free appliance to fit your homes
unique needs. Kit part numbers are provided
on pages 16 and 17 along with descriptive
illustrations.
The appliances covered in this manual are
heater rated and produce a great deal of heat.
Decorative brass trim pieces and hoods may
tarnish because of their proximity to the heater
opening and front face. Tarnishing of these
pieces is normal, unavoidable and should be
expected.
Forced Air Kit
The FAB-1100 assembly provides a forced air
circulation feature for your appliance. This kit
mounts directly into the lower intake chamber
with an electrical connection made at the recep-
tacle provided. The appliance must have an
independent 120Vac power line incorporated at
the time of installation. Refer to Step 6 of the
installation instructions supplied with the forced
air kit ( Figures 22 and 23 ).
Figure 22
Hide quick links:
Advertisement
Table of Contents
