Advertisement
1. Press MODE until TIMER appears.
2. Press SET/RECALL. Hour digits flash.
3. Press + / – to change hour.
4. Press NEXT and + / – to set minutes.
5. Press NEXT and + / – to set seconds.
6. Press NEXT and + / – to select STOP AT END or REPEAT AT END.
7. Press DONE to confirm and exit.
8. Press START/LAP to start Timer. Timer will continue to run if you exit Timer mode.
9. An alarm melody chimes when Timer reaches zero or before it starts to countdown again.
10. Press STOP/RESET to stop Timer. Press again to reset.
TIPS: •
appears in Time display when Timer is running.
• For repeat Timer operation, repetition number appears at top right of screen in both count-
down and interval Timers.
• Maximum number of repeats is 99.
You can set two Timers that countdown in sequence.
1. Press MODE until INTTMR appears.
2. Press SET/RECALL. INT 1 flashes.
3. Press NEXT then follow steps 3-6 in Timer section.
4. When return to INT 1 Press + / – to change to INT 2 (Interval 2).
5. Press NEXT then follow steps 3-6 in Timer section.
6. Press DONE to confirm and exit.
7. Press START/LAP to start Timer. Other operations are the same as for TIMER.
TIPS: • When first countdown is complete, Timer proceeds to the next non-zero interval that is set.
INDIGLO flashes and beep sounds between each interval.
• If you set both Timers in Interval Timer to repeat, Timer will countdown both intervals and
then repeat entire sequence.
1. Press MODE until ALM 1 appears.
2. Press SET/RECALL to set alarm.
3. Hour digits flash. Press + / – to change hour.
4. Press NEXT and + / – to set minutes, AM or PM (if primary time display is in 12-hour format), DAILY,
WKDAYS, WKENDS, or day of the week (weekly alarm).
5. Press DONE to confirm and exit.
6. Press START/LAP or STOP/RESET to turn Alarm ON or OFF.
7. To set remaining alarms, press MODE for ALM 2 or ALM 3 and set as above.
TIPS: • When Alarm is on,
appears in Time display.
• When Alarm goes off, INDIGLO® night-light and alarm icon flash and alert sounds. Press any
button to silence.
• If no button is pushed, alert will cease after 20 seconds and Backup Alarm will activate after 5
minutes.
INDIGLO® NIGHT-LIGHT/NIGHT-MODE® FEATURE
1. Press INDIGLO to activate night-light. Electroluminescent technology (U.S. pat. 4,527,096 and
4,775,964) illuminates entire watch face at night and in low light conditions.
2. Continue to press up to 3 seconds to maintain illumination.
3. Press and hold INDIGLO for 4 seconds to activate NIGHT-MODE® feature (U.S. pat. 4,912,688) feature.
will appear.
4. In NIGHT-MODE®, push any button to illuminate watch face for 3 seconds.
5. To deactivate NIGHT-MODE® feature, press INDIGLO for 4 seconds. Feature will automatically deac-
tivate after 8 hours.
WATER & SHOCK RESISTANCE
If your watch is water-resistant, meter marking or (
Water-Resistance Depth
30m/98ft
50m/164ft
100m/328ft
*pounds per square inch absolute
WARNING: TO MAINTAIN WATER-RESISTANCE, DO NOT PRESS ANY BUTTONS UNDER WATER.
1. Watch is water-resistant only as long as lens, push buttons and case remain intact.
2. Watch is not a diver watch and should not be used for diving.
3. Rinse watch with fresh water after exposure to salt water.
4. Shock-resistance will be indicated on watch face or caseback. Watches are designed to pass ISO test
for shock-resistance. However, care should be taken to avoid damaging crystal/lens.
W-105
861-095002
TIMER
INTERVAL TIMER
ALARM
) is indicated.
p.s.i.a.* Water Pressure Below Surface
60
86
160
3
www.timex.com
Advertisement
