OLS-32/40/46/7001PGB/P Safety Instructions Do not use a damaged or loose plug. This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire. Use only a properly grounded plug and receptacle.
Page 4
OLS-32/40/46/7001PGB/P Do not disconnect the power cord while using the LCD Display. A surge may be caused by the separation and may damage the LCD Display. Do not use the power cord when the connector or plug is dusty. If the connector or plug of the power cord is dusty, clean it with a dry cloth.
Page 5
OLS-32/40/46/7001PGB/P Do not place the LCD Display face down. This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm / 4 inches) for ventilation purposes.
Page 6
OLS-32/40/46/7001PGB/P Do not install the product on an unstable, uneven surtace or a location prone to vibrations. Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations mayshorten the lifetime of the product or may cause the product to catch fire.
Page 7
OLS- -32/40/46 6/7001PG GB/P mportan t Safety y Instru ctions 1. Rea d these instr ructions. 2. Keep p these instr ructions. 3. Hee d all warning 4. Follo ow all instruc ctions. 5. Do n not use this a apparatus ne ear water.
OLS-32/40/46/7001PGB/P Introduction LCD Display Manual User Manual CD Cable AC Power Cable HDMI Cable (Option) Other Remote Control Batteries (AAA X 2) 8 of 30...
Page 9
OLS-32/40/46/7001PGB/P Front 1. IR Aim the remote control towards this spot on the LCD Display. 2. LED LCD Power Status display(On : BLUE / Off : RED) 3. OSD KEY Input(Power / Menu / Source / Left / Right / Up / Down) a) Power : Turns the LCD Display On/ Off.
Page 10
OLS-32/40/46/7001PGB/P Rear 1. AC Power S/W On/Off. 2. AC Power In.(100V ~ 240V) 3. HDMI Out. 4. VGA Out. 5. DVI Out. 6. ESATA (2EA). 7. PS/2 Keyboard. 8. USB2.0 (6EA) 9. RJ45 LAN. 10. Audio Port.(Line-In / Line-Out / MIC-In) 11.
OLS-32/40/46/7001PGB/P Remote control 1. POWER: Turns the LCD Display On and Off & PC Power On and Off. 2. UP : Control the UP cursor in the menu 3, LEFT : Control the LEFT cursor in the menu 4, RIGHT : Control the RIGHT cursor in the menu 5, ENTER : Control the ENTER cursor in the menu 6, DOWN : Control the DOWN cursor in the menu 7.
OLS-32/40/46/7001PGB/P Viewing the Menus ◆ Press the MENU button. The main menu is displayed on the screen. Its left side has five Text: Color, Image Setting, Position , OSD Meuu, Language, Misc., Audio and Exit. Changing the Color Standard Your television has several setting options that allow you to control the picture quality. 1.
Page 13
OLS-32/40/46/7001PGB/P 3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. ◆ Contrast –Brightness– Color Adjust –Color Temp –Back ◆ Adjusts the Contrast and Brightness. 3-1. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. 3-2 Press the ▶...
Page 14
OLS-32/40/46/7001PGB/P : It adjusts the intensity of the color. ◆ Adjust the Color. 3-3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. 3-4.Select the required mode by pressing the ◀ or ▶ button, then press the ENTER button. ◆...
Page 15
OLS-32/40/46/7001PGB/P ◆ Adjusts the Color Temp. 3-6. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. 3-7. Press the ▶ button until you reach the optimal setting. ◀ ◆ 9300 – 6500 – 5800 - sRGB - USER ◆9300: This results in a blue tone.
Page 16
OLS-32/40/46/7001PGB/P 1. Press the MENU button to display the menu. 2. Press the ▲ or ▼ button to select Image Setting, then press the ENTER button. 3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. ◆...
Page 17
OLS-32/40/46/7001PGB/P ◆ Adjusts the Phase. 3-3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. 3-4. Press the ▶ button until you reach the optimal setting. ◀ ◆ Adjusts the Sharpness. 3-5. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. 3-6.
Page 18
OLS-32/40/46/7001PGB/P Changing the Position Standard 1. Press the MENU button to display the menu. 2. Press the ▲ or ▼ button to select Position, then press the ENTER button. 3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. ◆...
Page 19
OLS-32/40/46/7001PGB/P ◆ Adjusts the H.position and V.Position. 3-1. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. 3-2 Press the ▶ button until you reach the optimal setting. ◀ 4. Press the EXIT button or Back Select to exit. Changing the OSD Menu Standard 1.
Page 20
OLS-32/40/46/7001PGB/P 3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. ◆ OSD H.Pos – OSD V.Pos – OSD Time –Back ◆ Adjusts the OSD H.Pos OSD V.Pos. 3-1. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. 3-2 Press the ▶...
Page 21
OLS-32/40/46/7001PGB/P ◆ Adjusts the OSD Time. 3-3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. 3-4. Press the ◀ ▶ button until you reach the optimal setting. 4. Press the EXIT button or Back Select to exit. Changing the Language Standard 21 of 30...
Page 22
OLS-32/40/46/7001PGB/P 1. Press the MENU button to display the menu. 2. Press the ▲ or ▼ button to select Language, then press the ENTER button. 3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. ◆...
Page 23
OLS-32/40/46/7001PGB/P 1. Press the MENU button to display the menu. 2. Press the ▲ or ▼ button to select Misc., then press the ENTER button. 3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. ◆...
Page 24
OLS-32/40/46/7001PGB/P ◆ Reset 3-2. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. ◆ Reset: You can return to the factory defaults settings 4. Press the EXIT button or Back Select to exit. Changing the Audio Standard 24 of 30...
Page 25
OLS-32/40/46/7001PGB/P 1. Press the MENU button to display the menu. 2. Press the ▲ or ▼ button to select Audio., then press the ENTER button. 3. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. ◆...
Page 26
OLS-32/40/46/7001PGB/P ◆ Adjusts the Mute. 3-2. Press the ▶ button until you reach the optimal setting. ◀ 4. Press the EXIT button or Back Select to exit. Changing the Exit. 1. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. ◆...
OLS-32/40/46/7001PGB/P EWF (Enhanced Write Filter) Most of the characteristics of the XPE feature is to use the EWF. This is to protect the disk, as well as to protect the system files you can enjoy a twofer. The principle is simple. Jungle of the disk to the operating system and Overlay (RAM or Disk) and having the disk write When done, Overlay be made in writing is to create.