IBM eServer iSeries 825 Installation Instructions Manual
  1. Manuals
  2. Brands
  3. IBM Manuals
  4. Server
  5. eServer iSeries 825
  6. Installation instructions manual
IBM eServer iSeries 825 Installation Instructions Manual

IBM eServer iSeries 825 Installation Instructions Manual

In a rack
Hide thumbs Also See for eServer iSeries 825:
Table of Contents

Advertisement

Quick Links

Download this manual
ERserver
iSeries
Model 825
in a rack
installation instructions
Version 5

Advertisement

Table of Contents
loading

Related Manuals for IBM eServer iSeries 825

Summary of Contents for IBM eServer iSeries 825

  • Page 1 ERserver iSeries Model 825 in a rack installation instructions Version 5...
  • Page 3 ERserver iSeries Model 825 in a rack installation instructions Version 5...
  • Page 4 “Notices,” on page 47. Fourth Edition (August 2005) ® This edition applies to version 5, release 3, modification 0 of IBM Operating System/400 (product number 5722–SS1) and to all subsequent releases and modifications until otherwise indicated in new editions. This version does not run on all reduced instruction set computer (RISC) models nor does it run on CISC models.

  • Page 5: Table Of Contents

    . 28 Electronic Emission Notices . . 52 Install devices that were removed . . 32 Federal Communications Commission (FCC) Electrostatic discharge . . 32 statement . . 52 Install disk units . . 33 © Copyright IBM Corp. 2004, 2005...
  • Page 6 Model 825 In Rack Installation Instructions V5R3...

  • Page 7: Install A Model 825 In A Rack

    Since the design and configuration of rack enclosures varies, consideration must be given to the placement of IBM units into third party racks and third party units into IBM racks. It is the customer’s responsibility to ensure the unit can be safely mounted in the rack and the rack enclosure adequately provides proper ventilation/cooling, proper stability, and sufficient structural integrity for the unit when installed in the rack.

  • Page 8: Before You Begin

    __ 4. If there are incorrect, missing, or visibly damaged parts, contact one of the following: v Your authorized service provider ® v In the United States: IBM Rochester Manufacturing Automated Information Line (R–MAIL) at 1–800–300–8751 v In countries outside of the United States: Use the following Web site to locate your service and support numbers: http://www.ibm.com/planetwide...

  • Page 9: Rack Installation Instructions

    Ensure that you have a current backup of your system (including operating systems, licensed programs, and data) if you are installing an existing up and running unit in a rack. If you have installed logical partitions on your system unit, refer to the iSeries Information Center. Go to Manage logical partitions in the iSeries Information Center to find instructions on powering down a system with logical partitions.
  • Page 10 __ 7. Remove all the filler panels to allow access to the inside of the rack enclosure. Model 825 In Rack Installation Instructions V5R3...
  • Page 11 __ 8. Open the back door. Install a Model 825 in a rack...
  • Page 12 __ 9. Plan where you will place the units you are installing in the rack. Install units in the lower part first. Place the larger and heavier units in the lower part of the rack. Model 825 In Rack Installation Instructions V5R3...

  • Page 13: Rack Shelf Installation Instructions

    Rack shelf installation instructions __ 1. Locate the cable management arm assembly A , rack shelf with rail assembly B , adapter plate C , clips and screws D . Some extra screws are provided. __ 2. Install the adapter plate on the shelf. Locate the 10 screws to install the 825 adapter plate.
  • Page 14 __ 3. Install four clips on the front of the rack. If you are installing the system unit in the lower part of the rack, place the clips in EIA sections 1 and 2. Model 825 In Rack Installation Instructions V5R3...
  • Page 15 To install in the upper part, place the clips in EIA sections 17 and 18. Install a Model 825 in a rack...
  • Page 16 A Guidepins B Clips Model 825 In Rack Installation Instructions V5R3...
  • Page 17 C Empty __ 4. Two people are needed to install the shelf and rail assembly. One is positioned in back and the other one in the front of the rack. __ 5. Lift the shelf and rail assembly into the rack from the front. You need to slant the shelf to fit through the front opening.
  • Page 18 __ 7. Align and insert the guidepins on the rail assembly with the correct holes in the front frame. __ 8. Install two screws on each side of the back frame to secure the shelf assembly. __ 9. Open the latches A on the shelf. Slide the shelf partially out. Install the two screws on each side of the front frame to secure the shelf assembly.
  • Page 19 Note: If you have difficulty installing the screws, ensure the clips you previously installed are still in the correct position. __ 10. Slide the shelf into the rack. __ 11. Press in the latches to lock shelf in the rack. __ 12.

  • Page 20: Remove Devices Before Lifting The System Unit Into The Rack

    __ 14. Install two clips in the back frame B . __ 15. Install the two screws where the clips are located to attach the other end of the cable management arm to the back frame C . __ 16. The rack shelf and rail assembly installation is complete. __ 17.

  • Page 21: Remove Covers

    Remove covers Remove the front and side covers. __ 1. Remove the front cover by gripping the sides of the cover and pulling the cover toward you A . __ 2. Remove the side covers by loosening and removing the two thumbscrews and the two slotted retainer screws on the back.
  • Page 22 __ 3. Pull the cover out. Model 825 In Rack Installation Instructions V5R3...

  • Page 23: Remove Power Supply

    Remove power supply __ 1. Locate the power supply area at the back of the unit (P01 and P02). __ 2. Pull the latch on the power supply handle. __ 3. Lift up the handle on the power supply. __ 4. Support the bottom of the supply as you slide it out of the unit. Install a Model 825 in a rack...

  • Page 24: Electrostatic Discharge

    __ 5. Repeat the steps to remove the other power supply. Electrostatic discharge Attach the disposable wrist strap to prevent electrostatic discharge from damaging a device. View video. Attach the adhesive part of the foil to an unpainted surface on the frame of the unit. Notes: 1.
  • Page 25 __ 3. Squeeze and pull the handle out toward you and down before you remove the disk unit. If the handle is not all the way down, the disk unit will not slide out of the system. __ 4. Support the bottom of the disk unit assembly as you slide it completely out of the system. Do not hold the disk unit by the handle.

  • Page 26: Remove Fans

    Remove fans __ 1. Locate the fans in the front of your system unit (B01 and B02). __ 2. Remove the fan assembly by pulling the latches. Model 825 In Rack Installation Instructions V5R3...
  • Page 27 __ 3. Repeat for each fan. Install a Model 825 in a rack...

  • Page 28: Remove Tape, Cd-Rom And Dvd Devices

    Remove tape, CD–ROM and DVD devices __ 1. Locate the devices on the front of the system unit. __ 2. Pull both handles on both sides of the device toward you. __ 3. Slide the device out. __ 4. Do not hold the device by the handles. __ 5.

  • Page 29: Remove Processor Assembly

    __ 6. Repeat the steps to remove each device. Remove processor assembly __ 1. Locate the processor assembly inside the side of the system unit. __ 2. Remove the access cover A . __ 3. Remove the processor card assemblies by doing the following: Install a Model 825 in a rack...

  • Page 30: Remove The Network Interface Card

    __ a. Label the processor card assemblies and the location so they can be installed later in the same location. __ b. Unlatch the two latches until the card assembly slightly “pops” out. __ c. Pull on both latches at the same time to remove the card assembly from the system unit. __ d.

  • Page 31: Remove Pci Cards

    __ 5. Unlatch the two latches until the card assembly slightly “pops” out B . __ 6. Pull on both latches at the same time to remove the card assembly from the system unit C . __ 7. Put the card assembly in a static protective bag. Remove PCI cards __ 1.
  • Page 32 C09 HSL C08 HSL Imbed IOA __ 6. Open the latch at the card position where you plan to remove the card. Move the latch counterclockwise and then swing the latch out. Model 825 In Rack Installation Instructions V5R3...
  • Page 33 __ 7. Remove the card. Install a Model 825 in a rack...

  • Page 34: Install Unit In The Rack

    __ 8. Place the card in a static protective bag. __ 9. Repeat the steps for each card. Install unit in the rack Use the following instructions to lift the system unit into the rack and attach it to the shelf. __ 1.
  • Page 35 __ 3. CAUTION: The weight of this part or unit is between 32 and 55 kilograms (70.5 and 121.2 pounds). It takes three persons to safely lift this part or unit. (RSFTC205) __ 4. Pull the rack shelf out until fully extended and locked in place. __ 5.
  • Page 36 __ 6. Lift the unit onto the shelf. __ 7. Position the unit close to the front of edge of the shelf, approximately 2.5 centimeters. __ 8. Remove the side covers with lifting bars. __ 9. Remove the air flow deflector. Model 825 In Rack Installation Instructions V5R3...
  • Page 37 __ 10. Move the bottom of the foam forward out of the way A . Install a Model 825 in a rack...

  • Page 38: Install Devices That Were Removed

    __ 11. Install the two screws in the unit to secure the rack shelf. One screw location is in the back power supply area B . The other screw location is in the front foam area C . __ 12. Move the foam back in place. __ 13.

  • Page 39: Install Disk Units

    3. Attach the copper foil to an exposed, unpainted metal surface on the frame of the unit (electrical ground). Install disk units __ 1. The disk units are located in the front of your system unit. __ 2. Locate the disk drives and look at the label of the disk unit. It is very important to replace the disk units in the same exact location where they were removed.

  • Page 40: Install Fans

    Do not hold the disk unit by the handle. __ 4. __ 5. Support the bottom of the disk unit assembly, slide the disk unit all the way in and lock it in place by closing the latch. __ 6. Repeat the above steps for each disk unit in your system. __ 7.

  • Page 41: Install Tape, Cd-Rom And Dvd Devices

    __ 3. Push in the latches. Install tape, CD–ROM and DVD devices __ 1. Install the device by sliding it forward and into the system unit. You may need to remove the filler blank above the control panel. __ 2. Push the two latches that secure the device to the system unit frame until they stop. Install a Model 825 in a rack...

  • Page 42: Install Network Interface Card

    __ 3. Repeat the steps for each removable media device. Install network interface card __ 1. Make sure you install the network interface card before the processor assemblies. __ 2. Install any external cables from the card. __ 3. Slide the card assembly into the system unit A . Model 825 In Rack Installation Instructions V5R3...

  • Page 43: Install Processor Assembly

    __ 4. Push on both card latches at the same time. __ 5. Close the latches when you cannot push the card assembly any further into the system unit B . __ 6. Install the small cover on the top C . __ 7.
  • Page 44 __ 2. Install the access cover A . __ 3. Repeat the steps to install all processor card assemblies. Model 825 In Rack Installation Instructions V5R3...

  • Page 45: Install Pci Cards

    Install PCI cards __ 1. Locate the adapter card positions inside your system unit. __ 2. It is very important to install the card back into the same position it was removed. Use the information you recorded earlier in step 5 on page 25. __ 3.
  • Page 46 Model 825 In Rack Installation Instructions V5R3...

  • Page 47: Install Covers

    __ 4. Attention: Adapter cards are fragile: v Handle only by the edges. v Keep fingers off printed circuit area. v Use static strap when handling. v Leave in protective packaging until ready to install. __ 5. Start at the bottom when installing the cards. __ 6.
  • Page 48 __ a. Install the thumbscrews on the back, left side cover (view from front). __ b. Install the slotted retainer screws on the back, right side cover (view from front). Slide the shelf partially in to have space to tighten the screws with the tool provided. __ 2.
  • Page 49 __ 4. Close the latches. __ 5. Replace filler panels in empty spaces. __ 6. Install the black cover strips over the holes on each side of the unit. Install a Model 825 in a rack...
  • Page 50 Model 825 In Rack Installation Instructions V5R3...

  • Page 51: Install Power Supply

    __ 7. Install the rack trim on the sides and top that you removed when unpacking the rack. Install power supply You will install the following devices: __ 1. Locate the power supply area at the back of the unit. __ 2.
  • Page 52 Model 825 In Rack Installation Instructions V5R3...

  • Page 53: Appendix. Notices

    Consult your local IBM representative for information on the products and services currently available in your area. Any reference to an IBM product, program, or service is not intended to state or imply that only that IBM product, program, or service may be used. Any functionally equivalent product, program, or service that does not infringe any IBM intellectual property right may be used instead.

  • Page 54: Trademarks

    All statements regarding IBM’s future direction or intent are subject to change or withdrawal without notice, and represent goals and objectives only. All IBM prices shown are IBM’s suggested retail prices, are current and are subject to change without notice. Dealer prices may vary.

  • Page 55: Terms And Conditions For Downloading And Printing Publications

    Publications or any information, data, software or other intellectual property contained therein. IBM reserves the right to withdraw the permissions granted herein whenever, in its discretion, the use of the Publications is detrimental to its interest or, as determined by IBM, the above instructions are not being properly followed.

  • Page 56: Electronic Emission Notices

    Properly shielded and grounded cables and connectors must be used in order to meet FCC emission limits. IBM is not responsible for any radio or television interference caused by using other than recommended cables and connectors or by unauthorized changes or modifications to this equipment.
  • Page 57 Dieses Gerät ist berechtigt in Übereinstimmung mit Dem deutschen EMVG vom 9.Nov.92 das EG–Konformitätszeichen zu führen. Der Aussteller der Konformitätserklärung ist die IBM Germany. Dieses Gerät erfüllt die Bedingungen der EN 55022 Klasse A. Für diese von Geräten gilt folgende Bestimmung nach dem EMVG: Appendix.

  • Page 58: Electronic Emission Notices

    Dieses Genehmigungsverfahren ist von der Deutschen Bundespost noch nicht veröffentlicht worden. Electronic Emission Notices The following Statement applies to this IBM product. The statement for other IBM products intended for use with this product will appear in their accompanying manuals.
  • Page 59 This product is in conformity with the protection requirements of EC Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to electromagnetic compatibility. IBM cannot accept responsibility for any failure to satisfy the protection requirements resulting from a non-recommended modification of the product, including the fitting of non-IBM option cards.
  • Page 60 Model 825 In Rack Installation Instructions V5R3...
  • Page 62 Printed in USA...

Table of Contents