Table of Contents
Advertisement
6. Operation
6.1 Charging the battery (Fig. 2-3)
1. Remove the battery pack (5) from the handle
(Fig. 2) by pressing the pushlock buttons (8)
on the left and right side of the battery pack
(5).
2. Check that your mains voltage is the same as
that marked on the rating plate. Plug the char-
ging cable (7) of the charging unit (6) into the
power socket. The green LED on the charging
unit then comes on.
3. Insert the battery pack (5) into the battery
charger (6). The red LED will come on to in-
dicate that the battery pack is being charged.
Charging has fi nished when the red LED
goes out and the green LED comes on again.
The battery pack may become a little warm
during the charging process. This is normal.
Caution! At temperatures of 45°C and higher the
battery cannot be charged. In this case remove
the battery from the charger, let it cool down and
then recharge it.
If the battery pack fails to charge, check for the
following:
•
Voltage at the power socket
•
Good contact at the charging contacts of the
charging unit
If the battery pack still fails to charge, send
•
the charging unit
•
and the battery pack
to our customer service center.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the power of the cordless equipment
drops. Never fully discharge the battery pack. This
will cause it to develop a defect!
6.2 Torque setting (Fig. 4 / Item 1)
The cordless hammer drill/screwdriver is fi tted
with a mechanical torque selector.
The torque for a particular screw size is set with
the setting ring (1). The torque is dependent on a
number of factors:
•
On the type and hardness of the material in-
volved
•
On the type and length of the screws used
Anl_BT_CD_18_1_i.indb 7
Anl_BT_CD_18_1_i.indb 7
GB
•
On the requirements that the screw connec-
tion has to satisfy
The grating disengagement of the coupling in-
dicates that the selected torque level has been
reached.
Caution! Only ever adjust the setting ring
when the equipment is at a standstill.
Caution! For screwing purposes, the drill/ham-
mer drill selector switch (13) must be changed to
the „Drill" setting!
6.3 Drilling (Fig. 4/Item 1)
For drilling purposes, adjust the setting ring for
the torque to the last setting "Drill". In the drill
setting the slip coupling is non-functional. The
maximum torque is available for drilling.
6.3 Drilling/hammer drilling (Fig. 4)
•
For drilling purposes, adjust the torque setting
(1) and the drill/hammer drill selector switch
(13) to the „Drill" setting. The slip coupling is
now off and the maximum torque is available.
•
For hammer drilling purposes, adjust the
torque setting (1) to the „Drill" setting and the
drill/hammer drill selector switch (13) to the
„Hammer" setting. Once again the slip coup-
ling is off and the maximum torque is availab-
le.
Caution! Adjust the torque setting (1) and the
drill / hammer drill selector switch (13) only
when the equipment is at a standstill.
6.4 Changeover switch (Fig. 5/Item 3)
The slide switch above the On/Off switch is for
setting the direction of rotation of the cordless
hammer drill/screwdriver and for preventing the
cordless hammer drill/screwdriver from being
switched on inadvertently. You can select between
clockwise and counter-clockwise rotation. To avo-
id causing damage to the gearing, the direction of
rotation must only be changed when the screwdri-
ver is at a standstill. When the slide switch is in
the middle position, the On/Off switch is blocked.
- 7 -
09.08.12 18:14
09.08.12 18:14
Advertisement
Table of Contents
