Channel Set Up; Deleting (Or Adding) Channel - Sylvania SRC2213E Owner's Manual

CHANNEL SET UP

You can program the tuner to scan all the channels
you receive in your area.
NOTE: Channel memory programming is NOT
needed when connected to a cable box or satellite
box. Just select the TV/VCR channel selector to the
output channel of the cable box or satellite box (Ex
CH3). Then select the channel to be viewed on the
Cable Box or Satellite Box.
Make sure ...
•
Press the POWER button to turn on the TV/VCR.
1
Select "CHANNEL SET UP"
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L but-
ton to point to "CHANNEL SET
UP".
Then, press the F.FWD/B button.
2
Begin auto ch programming
Press the PLAY/K or STOP/L but-
ton to point to "AUTO CH PRO-
GRAMMING".
Then, press the F.FWD/B button.
The tuner scans and memorizes all
the active channels in your area.
3
After scanning
The tuner stops on the lowest memorized channel.
•
When AUTO CH PROGRAMMING is activated
where there is no TV signal input, "NO TV SIG-
NALS" will appear on the display after the com-
pletion of the channel scanning.
•
The TV/VCR may display TV channels to be
CATV channels caused by poor antenna reception.
In this case, try auto ch programming again.
The channels you no longer receive or seldom watch
can be deleted from the memory. (Of course, you
can add the deleted channel into the memory again.)
1
Press the MENU button on the
remote control.
Press the PLAY/K or STOP/L but-
ton to point to "CHANNEL SET
UP".
Then, press the F.FWD/B button.
2
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
Press the PLAY/K or STOP/L but-
SETTING CLOCK
B CHANNEL SET UP
ton to point to "ADD/DELETE
USER'S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CH".
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
Press the F.FWD/B button.
3
Press the PLAY/K or STOP/L but-
ton until your desired channel num-
– CHANNEL SET UP –
ber appears. (You can also use the
ADD / DELETE CH (CATV)
number buttons or the CHANNEL
B AUTO CH PROGRAMMING
K/L button to enter it) (Example:
CH8)
•
When selecting cable channels which are higher
than 99, press the +100 button first, then, press the
last two digits. (Example: to select channel 125,
first press the +100 button then press "2" and "5").
•
You must proceed single-digit channel numbers
with a zero (Example: 02 ... 09).
4
Press the F.FWD/B or REW/s button. The channel
number changes to light red. The channel is deleted
from memory.
•
To delete another channel, repeat steps [3] and [4].
•
If you press the F.FWD/B or REW/s button
again, the channel is memorized again.
Added channel: Light blue.
Deleted channel: Light red.
5
Press the MENU button on the remote control to
returns to TV mode.
NOTE: To confirm that channel(s) has been deleted
or added, press the CHANNEL K or L button.
- 13 -
DELETING (OR ADDING)
CHANNEL
Select "CHANNEL SET UP"
Select "ADD/DELETE CH"
Enter the desired channel number
Delete (or add) it from (into) memory
Exit the channel setup mode
– M E N U –
TIMER PROGRAMMING
PICTURE CONTROL
SETTING CLOCK
B CHANNEL SET UP
USER'S SET UP
V-CHIP SET UP
LANGUAGE [ENGLISH]
CAPTION [OFF]
ZERO RETURN
TIME SEARCH
– CHANNEL SET UP –
B ADD / DELETE CH (CATV)
AUTO CH PROGRAMMING
08
ADD / DELETE
EN
9I03