Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Pentair Manuals
  4. Grinder
  5. Hydromatic TL-Pro
  6. Installation and service manual

Pentair Hydromatic TL-Pro Installation And Service Manual

Complete grinder package offering. for use with hpg(x)200 and hpgr200 hydromatic grinder pumps.
Hide thumbs

Advertisement

Quick Links

Download this manual
MODEL TL-PRO SYSTEM
COMPLETE GRINDER
PACKAGE OFFERING
INSTALLATION AND SERVICE MANUAL
For use with HPG(X)200 and HPGR200 Hydromatic Grinder Pumps.
NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible
party who maintains the system.
Item # E-03-457 | Part # 5625-457-1 | © 2012 Pentair Pump Group, Inc. | 10/31/12

Advertisement

loading

Related Manuals for Pentair Hydromatic TL-Pro

Summary of Contents for Pentair Hydromatic TL-Pro

  • Page 1 NOTE! To the installer: Please make sure you provide this manual to the owner of the equip ment or to the responsible party who maintains the system. Item # E-03-457 | Part # 5625-457-1 | © 2012 Pentair Pump Group, Inc. | 10/31/12...

  • Page 2: General Information

    system is not intended for use in General Excavation hazardous locations per NFPA 70 National Electric Code. Information Instructions Consult factory for optional equipment rated for this use. Thank you for purchasing your Low Pressure Sewer Basin System. Cutting risk. Risk of serious Excavation location shall be cutting or amputation exists.
  • Page 3 Step 1: hub is used, refer to the directions Backfill included with the hub. The pad under the basin requires Instructions 4 to 6 inches of appropriate fill. Determine point at which influent The ideal basin pad is concrete line will enter basin and, using a in conjunction with antiflotation properly maintained piloted hole Authority...
  • Page 4 Step 3: be positive that correct bed and down the dual rails, allowing backfill materials are used per the pump to be removed without Position pump so the guide rails instructions as follows: disconnecting the piping. are located in the slots of the a.

  • Page 5: Typical Installation

    All conduits and cables unless it is placed in operation. entering the panel must be sealed If a pump has been out of service NOTE: Failure to use a Pentair off. for an extended period of time, approved control panel voids...
  • Page 6 Preoperational Grinder Pump shuts off when the water level is Pump Checks: 2 inches above the pump volute discharge. Operations Step 1: Float adjustment for duplex Ensure power source is off or systems: Adjust floats so that a disconnected. Step 1: pump will start when the water level is just above the pump motor Run clear water into the basin...

  • Page 7: Pump Troubleshooting

    6. Discharge head may be too replace the float(s) or replace Pump high. Check elevation against the alternator relay if the design point of pump. system is duplex. Troubleshooting 7. Clogging beyond the sealing flange. This is evident if Seal Failure Light Comes On. Following is a list of common water is discharged through 1.
  • Page 8 Pump Troubleshooting Overload trips, is manually reset, and then trips off again. 1. Cutters may be clogged. It is possible that the pump stalled during operation, and starting and stopping cleared the cutters. If resetting the overloads solves this problem, return the H-O-A switch to Auto and observe operation.
  • Page 9 Fiberglass Simplex Parts List ORDERING REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be fur- nished as long as it is in ter change able with the old part.When ordering re place ment parts, always furnish the fol low ing information: (1) pump serial num ber, (2) pump model and size, (3) part description, (4) part number, (5) im pel ler diameter (if ordering impeller).
  • Page 10 Fiberglass Duplex Parts List ORDERING REPLACEMENT PARTS: Product improvements are made from time to time. The latest part design will be fur- nished as long as it is in ter change able with the old part.When ordering re place ment parts, always furnish the fol low ing information: (1) pump serial num ber, (2) pump model and size, (3) part description, (4) part number, (5) im pel ler diameter (if ordering impeller).
  • Page 11 THIS PAGE INTENTIONALLY LEFT BLANK...

  • Page 12: Standard Limited Warranty

    Pentair Hydromatic will cover only the lower seal and labor thereof for all dual seal pumps. under no circumstance will Pentair Hydromatic be responsible for the cost of field labor, travel expenses, rented equipment, removal/reinstallation costs or freight expenses to and from the factory or an authorized Pentair Hydromatic service facility.