TO PREVENT RISK OF SHOCK
DISCONNECT TELEPHONE LINE
AT TELECOM JACK BEFORE
SERVICING THIS UNIT.
RJ11
TO
INCOMING
HANDSET
PHONE
LINE
LOCAL SOUNDER
DISABLE SHUNT
REMOVE TO
DISABLE
THE READYGUARD-R SERIES
CONTROLS ARE EQUIPPED WITH
AN INTEGRAL RECHARGEABLE
BATTERY PACK
P/N LYNXRCHKIT-SC.
FOR UL985 APPLICATIONS INSTALL
P/N LYNXRCHKIT-HC
REPLACE EVERY FOUR YEARS
System Programming
Certain features differ between the ReadyGuard-R and the ReadyGuard-REN models. Verify the specific model being
installed prior to the system programming.
Step
1.
Set a programming default as follows:
a.
Enter Programming mode: Installer Code + 8 0 0.
✻
b.
Press
97, then press a number 1-4 to select a default table from the tables listed.
2.
Program the variable data fields as follows:
a.
RF House ID - Press
b.
PABX Access Code (if used) - Press
to end the field and advance to the next field.
c.
Primary Phone Number - Press
digits are used, press [
d.
Secondary Phone Number (if used ) - Press
fewer than 24 digits are used, press [
e.
Secondary Account Number (if used) - Press
are used, press [
f.
Pager Characters - Press
by your pager service (e.g. account number, PIN, etc.). If fewer than 16 digits are used, press [
field and advance to the next field.
g.
Download Phone Number - Press
If fewer than 20 digits are used, press [
ALL OUTPUT CIRCUITS ARE POWER LIMITED.
WARNING:
EARTH
GROUND
PHONE
8
1
2
3
5
4
POS
JACK
TIP
RING
TIP
RING
PHONE
LINE
INCOMING
TELEPHONE
LINE
EARTH
PREMISES
GROUND
TELEPHONE
WEEKLY TESTING IS
REQUIRED TO ENSURE
PROPER OPERATION
OF THIS SYSTEM
READYGUARD-R-SERIES WIRING CONNECTIONS
✻
24, then enter the desired 2-digit RF House ID for wireless keypads.
✻
41, then enter the primary phone number, up to 20 digits. If fewer than 20
✻
] to end the field and advance to the next field.
✻
✻
] to end the field and advance to the next field.
✻
88 if using Default Table 2 or 4, then enter up to 16 digits, which may be required
✻
94, then enter the downloading computer phone number, up to 20 digits.
AAV / LRR
TRIGGER
(READYGUARD-R)
LRR
TRIGGER
(READYGUARD-REN)
ZONE
SOUNDERS
11
6
7
8
9
10
(+)
( )
( )
(+)
( )
HARD
WIRED
ZONE
TRIGGER
SIGNAL
(NEG)
PIEZO
BELL
2k OHMS
6-14VDC
EOLR
30mA max.
6-14VDC
120mA max.
(e.g. WAVE2EX)
NOTE
USE ONLY 1332/1332X10 OR 1332CN
TRANSFORMERS PROVIDED
Action
✻
40, then enter up to 6 digits. If fewer than 6 digits are used, press [
✻
42, then enter the secondary phone number, up to 24 digits. If
] to end the field and advance to the next field.
✻
44, then enter the secondary account number. If only 3 digits
✻
] to end the field.
-3-
PLCD
AC
12
13
14
15
16
DATA
(+)
SYNC
OUT
IN
1332/
1332X10/
1332CN
PLUG-IN
TRANSFORMER
9VAC, 15VA
AC
AC
SYNC
COM
DATA
1332X10
ONLY
CONNECTIONS
01100-004-V1
✻
]
✻
] to end the