1. Manuals
  2. Brands
  3. BMW Manuals
  4. Car Stereo System
  5. Retrofit kit Sound Module System II
  6. Installation instructions manual

BMW Retrofit kit Sound Module System II Installation Instructions Manual

Bmw 3 series touring e46/3. left-hand drive (lhd)
Hide thumbs
Table of Contents

Advertisement

Quick Links

BMW Parts and Accessories
Installation Instructions
Retrofit kit Sound Module System II for
BMW 3 Series touring E46/3, left-hand drive (LHD)
Technical and electrical knowledge is required
Installation time approx. 2.5 hours, which can vary according to the condition and fittings of
the vehicle.
Retrofit/Installation Kit no. 82 83 0 022 122
Retrofit/Installation Kit no. 82 83 0 022 122
Installation Instructions no. 01 29 0 022 772
Date: 04.2000
F 46 0714 B

Advertisement

Table of Contents
loading

Related Manuals for BMW Retrofit kit Sound Module System II

Summary of Contents for BMW Retrofit kit Sound Module System II

  • Page 1 BMW Parts and Accessories Installation Instructions F 46 0714 B Retrofit kit Sound Module System II for BMW 3 Series touring E46/3, left-hand drive (LHD) Technical and electrical knowledge is required Installation time approx. 2.5 hours, which can vary according to the condition and fittings of the vehicle.

  • Page 2: Table Of Contents

    Contents Chapter Page 1. Preparatory work......................31 2. Parts overview......................32 3. Choose mounting system for amplifier (only vehicles without on-board monitor radio) ............35 4. Install amplifier and supplementary wiring harness (mounting system at cross brace, only vehicles without on-board monitor radio with battery in the engine compartment ) ..........36 5.
  • Page 3 (maintenance, repair, diagnostic, etc.). This high-quality audio system is for use only in combination with an original BMW car radio! If connected to a non-BMW make, BMW AG will accept absolutely no responsibility under the guarantee for the Sound Module System.

  • Page 4: Preparatory Work

    Preparatory work TIS AW no. Carry out short test (print out error memory) Dismantle both door trim panels, front 51 41 000 Remove cellular covering from the standard woofers/mid-range speakers in the door trim panels (no longer required) Dismantle all four standard speakers in the doors, front (no longer required) Additionally in vehicles without on-board monitor radio Dismantle covering under steering column...

  • Page 5: Parts Overview

    2. Parts overview 21 22 Kunden Einbauanleitung information F 46 0715 B EN/33 Retrofit/Installation Kit no. 82 83 0 022 122 Date: 04.2000 Installation Instructions no. 01 29 0 022 772...
  • Page 6 Parts overview 1 Amplifier 2 Fillister head self-tapping screw 3.5x9.5 for amplifier on bracket (6 items) 3 Adapter for ground connection (only vehicles without on-board monitor radio) 4 Adapter cable radio/amplifier and on-board monitor radio/amplifier 5 Amplifier bracket for fitting against bulkhead (only vehicles without on-board monitor radio) 6 Tweeter/mirror triangle (2 items) 7 Amplifier bracket for fitting against I beam (only vehicles without on-board monitor radio) 8 Power cable with fuse...

  • Page 7: Choose Mounting System For Amplifier (Only Vehicles Without On-Board Monitor Radio)

    3. Choose mounting system for amplifier (only vehicles without on-board monitor radio) Illustration shows driver's footwell with view through the opening of the storage compartment on the left by the side of the steering column. If, at the installation location of the amplifier the cross brace (40) is fitted, you will have to proceed with the installation of the amplifier and supplementary wiring harness as described in...
  • Page 8 4. Install amplifier and supplementary wiring harness (mounting system at cross brace, only vehicles without on-board monitor radio with battery in the engine compartment ) Insert hexagon head screw M8x20 (21) from below into the bracket above (19). Place the bracket above (19) with inserted hexagon head screw M8x20 (21) on the amplifier (1) and screw it in with four fillister head self-tapping screws 3.5x9.5 (2).
  • Page 9 Install amplifier and supplementary wiring harness (mounting system at cross brace, only vehicles without on-board monitor radio with battery in the engine compartment ) Plug together the black 17-pole radio connector (40) with the black 17-pole pin housing (41) of the adapter cable (4).
  • Page 10 Install amplifier and supplementary wiring harness (mounting system at cross brace, only vehicles without on-board monitor radio with battery in the engine compartment ) Screw on bottom bracket (18) with two fillister head self-tapping screws 3.5x9.5 (2) to the amplifier (1). Attach adapter cable (4) along the length of the main wiring harness (40) with cable straps (16).
  • Page 11 Install amplifier and supplementary wiring harness (mounting system at cross brace, only vehicles without on-board monitor radio with battery in the engine compartment ) Push power cable (40), cable colour red, carefully through rubber grommet (41) and then through rubber grommet (42). Seal rubber grommet (41) at engine side with sealing compound.
  • Page 12 5. Install amplifier and supplementary wiring harness (mounting system at cross brace, only vehicles without on-board monitor radio with battery in the boot) Insert hexagon head screw M8x20 (21) from below into the bracket above (19). Place the bracket (19) on the amplifier (1) and screw it in with four fillister-head self-tapping screws 3.5x9.5 (2).
  • Page 13 Install amplifier and supplementary wiring harness (mounting system at cross brace, only vehicles without on-board monitor radio with battery in the boot) Plug together the black 17-pole radio connector (40) with the black 17-pole pin housing (41) of the adapter cable (4). If necessary, move the position of the plug of the connection cable for the CD changer in the black 17-pole socket housing (42) of the adapter...
  • Page 14 Install amplifier and supplementary wiring harness (mounting system at cross brace, only vehicles without on-board monitor radio with battery in the boot) Screw on bottom bracket (18) with two fillister head self-tapping screws 3.5x9.5 (2) to the amplifier (1). Attach adapter cable (4) along the length of the main wiring harness (40) with cable straps (16).
  • Page 15 Install amplifier and supplementary wiring harness (mounting system at cross brace, only vehicles without on-board monitor radio with battery in the boot) Install power cable (40), cable colour red, along the audio wiring harness as far as the rear seat bench and from there under the carpet along the rear seat bench to the vehicle wiring harness towards the right.
  • Page 16 6. Install amplifier and supplementary wiring harness (mounting system at I beam, only vehicles without on-board monitor radio with battery in the engine compartment) Place amplifier bracket for fitting against the I beam (7) on the amplifier (1) and screw it on with four fillister head self-tapping screws 3.5x9.5 (2).
  • Page 17 Install amplifier and supplementary wiring harness (mounting system at I beam, only vehicles without on-board monitor radio with battery in the engine compartment ) Connect adapter cable (4) to amplifier (1). Couple the 25-pole connector (40) of the adapter cable (4) to the plug strip (41) and, using a large flat-tip screwdriver (42), press in the direction of the arrow until it is heard to engage in the amplifier housing.
  • Page 18 Install amplifier and supplementary wiring harness (mounting system at I beam, only vehicles without on-board monitor radio with battery in the engine compartment ) Install ground cable (40), cable colour brown, with cable lug ø6mm and power cable (41), cable colour red, of the adapter cable (4) through the opening (42) into the control unit box in the engine compartment on the left.

  • Page 19: Install Amplifier And Supplementary Wiring Harness (Mounting System At I Beam, Only Vehicles Without On-Board Monitor Radio With Battery In The Engine Compartment )

    Install amplifier and supplementary wiring harness (mounting system at I beam, only vehicles without on-board monitor radio with battery in the engine compartment ) Install power cable (40), cable colour red, to connection point and cut off excessive length. Crimp on blade terminal contact (17) to the power cable (40) and insert at the supply line with fuse (8).

  • Page 20: Install Amplifier And Supplementary Wiring Harness

    Install amplifier and supplementary wiring harness (mounting system at I beam, only vehicles without on-board monitor radio with battery in the boot) Place amplifier bracket for fitting against the I beam (7) on the amplifier (1) and screw it on with four fillister head self-tapping screws 3.5x9.5 (2).
  • Page 21 Install amplifier and supplementary wiring harness (mounting system at I beam, only vehicles without on-board monitor radio with battery in the boot) Connect adapter cable (4) to amplifier (1). Couple the 25-pole connector (40) of the adapter cable (4) to the plug strip (41) and, using a large flat-tip screwdriver (42), press in the direction of the arrow until it is heard to engage in the amplifier housing.
  • Page 22 Install amplifier and supplementary wiring harness (mounting system at I beam, only vehicles without on-board monitor radio with battery in the boot) Install ground cable (40), cable colour brown, with cable lug ø6mm, of the adapter cable (4) through the opening (41) into the control unit box in the engine compartment on the left.
  • Page 23 8. Install amplifier and supplementary wiring harness (only vehicles with on-board monitor radio and battery in the engine compartment) Place amplifier bracket (11) on amplifier (1) and screw it on with four fillister head self-tapping screws 3.5x9.5 (2). Put on plug-in nuts M5 (13). Take note of the position of the opening (40) for the connector of the adapter cable.

  • Page 24: Install Amplifier And Supplementary Wiring Harness (Only Vehicles With On-Board Monitor Radio And Battery In The Engine Compartment)

    Install amplifier and supplementary wiring harness (only vehicles with on-board monitor radio and battery in the engine compartment) Install ground cable (40), cable colour brown, X13016 with cable lug ø6mm to ground point X13016 and screw it on. Combine the excess length of the adapter cable (4) into the form of a figure of eight and fasten it with cable ties in the side part at rear left.
  • Page 25 Install amplifier and supplementary wiring harness (only vehicles with on-board monitor radio and battery in the engine compartment) Push power cable (40), cable colour red, carefully through rubber sleeve (41) and then through rubber grommet (42). Seal rubber grommet (41) at the engine side with sealing compound.

  • Page 26: Install Amplifier And Supplementary Wiring Harness

    9. Install amplifier and supplementary wiring harness (only vehicles with on-board monitor radio and battery in the boot) Place amplifier bracket (11) on amplifier (1) and screw it on with four fillister head self-tapping screws 3.5x9.5 (2). Put on plug-in nuts M5 (13). Take note of the position of the opening (40) for the connector of the adapter cable.
  • Page 27 Install amplifier and supplementary wiring harness (only vehicles with on-board monitor radio and battery in the boot) Install ground cable (40), cable colour brown, X13016 with cable lug ø6mm to ground point X13016 and screw it on. Combine the excess length of the adapter cable (4) into the form of a figure of eight and fasten it with cable ties in the side part at rear left.

  • Page 28: Installation Of The Front Tweeters And The Front Woofers/Mid-Range Speakers

    10. Installation of the front tweeters and the front woofers/mid-range speakers Illustration shows mounting of the tweeter (6) on the left-hand side of the vehicle.You should proceed in the same logical sequence for mounting the tweeter on the right-hand side of the vehicle.

  • Page 29: Finalising Operations / Coding

    11. Finalising operations / coding Connect battery Carry out function test Reassemble vehicle in the reverse order of disassembly. Print out error memory This system is not coding-relevant. EN/57 Retrofit/Installation Kit no. 82 83 0 022 122 Date: 04.2000 Installation Instructions no. 01 29 0 022 772...

Table of Contents