Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Operator's Manual
Advertisement
Table of Contents
Related Manuals for Emerson E2 RX Series
Summary of Contents for Emerson E2 RX Series
- Page 1 026-1621 Rev 0 12-JUN-2012 Quick Start Guide for E2 RX Refrigeration, BX HVAC, and CX Convenience Store Controllers Applicable to E2 firmware versions 4.0 and above...
- Page 3 Retail Solutions 3240 Town Point Drive NW, Suite 100 Kennesaw, GA 30144, USA Phone 770-425-2724 Fax 770-425-9319 FCC COMPLIANCE NOTICE This device complies with Part 15 of the FCC Rules. Operation is subject to the fol- lowing two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
-
Page 5: Table Of Contents
Table of Contents 1 QUICK START................................1 1.1 L ................................. 1 OGGING 1.2 C ..........................1 LEANING UT THE ONTROLLER 1.3 S ........................2 ETTING UMBER OF ETWORK EVICES 1.4 S ..........................3 ETTING UMBER OF PPLICATIONS 2 SCREENS AND MENUS .............................. 3 2.1 T .......................... - Page 6 3.9.1.4 The Echelon Network (The Alarm Annunciator) ..................... 20 3.9.2 Setting up an E2 to be an Alarm Annunciator ..................... 21 3.9.3 Alarm Dial-Out ..............................21 3.9.4 Introduction: Alarm Reporting..........................22 3.10 S .............................. 22 LOBAL 3.10.1 Priority Settings..............................23 3.11 S ...............................
-
Page 7: Quick Start
Quick Start Cleaning Out the Controller This manual covers what to do when you are program- Cleaning out the E2 controller needs to be done if: ming an E2 for the first time. The manual includes logging on, specifying informa- •... -
Page 8: Setting Number Of Network Devices
Setting Number of RLDS leak detection units on this E2’s I/O Network. Unit Controllers (Echelon) Network Devices Liquid Ctrls (CC100P/CC100LS) Enter the com- bined number of pulse valve case controllers (CC100Ps) and liquid-side stepper valve case con- trollers (CC100LSs) in this field. Suction Controllers (CC100H) Enter the num- ber of suction stepper case controllers (CC100Hs) in this field. -
Page 9: Setting Number Of Applications
Screens and Setting Number of Applications Menus The Main Status (Home) Screen Figure 1-3 - Application Setup (RX version shown) The Application Setup screen is where you will enter information about the types of devices on the E2’s control system. If you know how many applications will be needed, this step will save you time and will keep you Figure 2-1 - Home Screen (RX version shown) -
Page 10: Common Screen Elements
Common Screen Icon Description Elements Wait, or system is busy Disk activity, or saving to disk Caps lock is ON Table 2-1 - Header Icons and Descriptions HEADER 2.2.2 The Function Keys HELP LINE Figure 2-4 - Home Screen Function Keys (RX version shown) FUNCTION KEY DESCRIPTIONS At the very bottom of every screen in the E2, there are... -
Page 11: Screen Types
Screen Types Each status screen is specially designed to provide a concise at-a-glance view of how one or more systems are 2.3.1 The Main Menu functioning. TIP: To view the Suction Group Status screen in the RX controller, start from the Home screen. -
Page 12: The Actions Menu
2.3.3 The Actions Menu Actions Menu Description Item Application Allows Service Start/End for Irriga- Commands tion and Pulse Accumulation applica- tions. Applications Opens various log and graph screens Logs/Graphs for Anti-sweat and Pulse Accumula- tion applications. Opens the Circuit Report screen for standard circuits only. -
Page 13: System Configuration Menu
2.3.5 System Configuration Menu Menu Option Description 7 - Network Setup Opens the Network Setup menu, where options to view network status, add or delete boards and controllers, commission devices, set up a router, and make board associations are available. 8 - Global Data Configure one or more analog or digital sensors to be used as... -
Page 14: Setup
Setup The System Information menu contains nine items: Menu Option Description Set Up Time/Date 1 - General Controller Edit general information about Info the E2, such as engineering units, and summer/winter change-over specifications. 2 - Time and Date Change the current date and time, and specify date formats. -
Page 15: Setting The Time And Date
3.1.1 Setting the Time and Date Log is added. If this field is set to No, the E2 clock will have to be set The Time Format field affects how times are displayed manually. If this field is set to Yes, SNTP support is used. and entered throughout the controller. -
Page 16: Set Up Modem
Daylight Savings Time uses GMT Press (Modem Setup) to advance to the Gen- This setting is only visible when Daylight Savings eral Services screen. Dates is set to User Defined DLT Dates. If set to Yes, You can choose between an internal modem (one that Daylight Savings Time uses GMT calculates the time to is mounted directly on to the E2 circuit board (via the change from GMT and the current time zone setting. -
Page 17: Set Up Network Baud Rates
Set Up Network Baud what IP address to enter. The IP Address always consists of four numbers Rates from zero to 255, each of which is separated by a period. Enter the address in this format. Subnet Mask Contact your network administrator NOTE: If a baud rate is changed in this screen, to get the correct subnet mask value, and enter it in the controller must be rebooted (turned OFF... -
Page 18: I/O Network Baud Rate
Set Up User Access Access the User Access Setup screen from the System Information menu: Press to open the Main Menu. Press (System Configuration). Press (System Information). Figure 3-5 - COM1 Baud Rate Setup (Serial RS232) 3.4.2 I/O Network Baud Rate The I/O Network baud rate is the rate at which the E2 will communicate with input and output boards on the... -
Page 19: Changing Required User Access Levels
for the username and password. If found, the E2 will log Each row has five columns, each of which corresponds the user in at the access level chosen for the user in the to a different category of user actions. user records. -
Page 20: Deleting A User
Type in the user name (Username), and then • Connected I/O Boards & Controllers move to the next field (Password) by pressing • Router Setup the right arrow button. • Controller Associations Type in a password for the next user, then press For the total (E2) devices online or offline, status, the right arrow button to advance to the next setup screens, changing board or controller names, config-... -
Page 21: Checking Online Status
Set Up Echelon put boards on this E2’s I/O Network. 4AO Boards Enter the number of 4AO analog out- Network put boards on this E2’s I/O Network. IRLDS Controllers Enter the number of leak detec- 3.7.1 Specifying Number of tor units on this E2’s I/O Network. Devices (Options will vary depending on the type of controller used.) -
Page 22: Commissioning A Device
(CC100Ps) and liquid-side stepper valve case con- trollers (CC100LSs) in this field. Suction Controllers (CC100H) Enter the num- ber of suction stepper case controllers (CC100Hs) in this field. Circuit Suction (CS100) Enter the number of suc- tion lineup circuit controllers (CS100s) in this field. ESR8 Line Up Boards Enter the number of ESR suction lineup circuit boards (SR100s) in this field. -
Page 23: The Service Button Method
3.7.2.1 The Service Button Method To commission a device using the service button, you CAUTION: When the E2’s Wait Time dura- must first set up the E2 to receive a service button signal, tion begins, the E2 will accept the first Neuron and then press the service button on the device. -
Page 24: The Manual Id Entry Method
The ESR8’s Service Button affixed to your form. Tear this tag off and stick it in the Neuron ID blank on the sheet of paper. If the perforated tag has already been removed, write the ID number in the blank. When all Neuron ID numbers have been collected, return to the E2 and enter the Neuron ID numbers for each device. -
Page 25: License Management
License Management Enter your license key to activate the desired feature: Some applications in the E2 are only available when activated with a license key that is obtained through Retail Solutions. Licensing allows the user to activate certain features in the E2. To obtain a license for a feature, go to the TCP/IP setup screen and obtain your E2 controller’s MAC ... -
Page 26: Set Up Alarming
3.9.1 Specifying Alarm Reporting changes. Types • Access Terminal Mode. • View Alarms. Apart from storing alarms it generates in its own Alarm Advisory Log, E2 can also report alarms it gener- To access Web Services: ates or receives in order to notify personnel. E2 can report Open a browser window and enter the IP Address of alarms in several different ways. -
Page 27: Setting Up An E2 To Be An Alarm Annunciator
3.9.3 Alarm Dial-Out • Users can view alarm notifications and alarm logs for all controllers from the Alarm Annunciator. • Only the Alarm Annunciator needs to be pro- grammed with alarm filter settings for dial-out, out- put, and display. All other controllers may be programmed to simply send all alarms to the Alarm Master via the LonWorks Network. -
Page 28: Introduction: Alarm Reporting
3.10 Set Up Global Data addresses. Use the and keys to cycle through the Setup screens. 3.9.4 Introduction: Alarm Reporting In general, a controller reports alarms to any or all of four different sources: 1. The E2 Display Header Alarms that occur within a E2 may be reported to the header display at the top of the screen. -
Page 29: 3.10.1 Priority Settings
global sensor values to all other Global Data applications point settings. on the E2. Example: Out of three E2s, an outside air temperature As a result, a single sensor can be used by any applica- sensor on E2 A’s I/O Network is set up as the primary tion in any E2 on the network. -
Page 30: 3.11 Set Up Applications
3.11.1 Add/Delete an Application User This setting means the E2’s global data will read (or be a “User” of) all values coming from the Add an Application: network. This setting is for E2s that are not con- nected to the sensor itself, but read the data that Press the key to open the Main Menu comes from it. -
Page 31: Using And Configuring A Setup Screen
3.11.2 Using and Configuring a names and board numbers. Setup Screen • Setup I/O - allows user to enter an input or output point setup screen. The Setup screen is application-specific depending on 3.11.2.2 Entering Setpoints where you place the cursor on the Home screen. ... -
Page 32: Navigating The Setup Screen
3.11.2.3 Navigating the Setup Screen TIP: To see each screen in a typical setup for the E2 RX controller, start from the Main Sta- tus (Home) screen. Position the cursor somewhere inside the Suc- tion Groups section and press (Setup), or just ... -
Page 33: Using The Help Key To Get Property Help
The Help Line The line near the bottom of the screen above the func- tion key menu is the help line. The help line this time pro- vides a short description of the selected field, along with important information such as minimum and maximum value ranges, and setup instructions. -
Page 35: Appendix A: Troubleshooting
Appendix A: Troubleshooting The chart below describes symptoms and solutions if troubleshooting the system or equipment is needed. For further information, contact Retail Solutions Service at 1-800-829-2724. SYMPTOM POSSIBLE PROBLEM SOLUTION I/O Network Problems I/O board not getting power. Check I/O board power--is the green STATUS light on? If not, check power wiring connections, and use a multimeter to verify the board is getting 24VAC. - Page 36 SYMPTOM POSSIBLE PROBLEM SOLUTION Compressor will not Operate Compressor is not programmed Verify that E2 was programmed for correct number properly. of compressor stages. Highlight the General tab (C1) in the Suction Group Setup screen. Is the cor- rect number of stages in the “Number of Stages” field? Compressor types are set up Make sure that compressor stages were properly set...
- Page 37 SYMPTOM POSSIBLE PROBLEM SOLUTION Compressor will not Oper- 8RO fail-safes are not wired Verify fail-safe wiring on 8RO board for N.O./N.C. ate (Cont.) correctly. positions. One wire of the two-wire connection should always be connected to the middle terminal. The second wire must be either connected to the N.C.
- Page 38 SYMPTOM POSSIBLE PROBLEM SOLUTION Problems with Condenser Condenser will not operate. Verify that E2 is programmed with proper number of fans. 1. Highlight the General tab (C1) in the Condenser Setup screen. 2. Is the correct number of fans in the Number of Fans field? Incorrect board and point set- Confirm proper board and point settings:...
- Page 39 SYMPTOM POSSIBLE PROBLEM SOLUTION Problems with Global Information cannot be read Verify that the controller with the sensor is set up as Actions from another E2 controller. the Primary and the controller receiving the infor- mation is set up as the User (both controllers default as local).
- Page 40 SYMPTOM POSSIBLE PROBLEM SOLUTION Lighting Control Problems Lights will not come on. Make sure you have a Time Schedule set up. A Time Schedule is not Lighting Control. You can use the same Time Schedule for several Lighting Con- trols. Set up the Time Schedule first and then assign it to a Lighting Control.
- Page 42 Emerson Climate Technologies Retail Solutions, Inc. and/or its affiliates (collectively “Emerson”), reserves the right to modify the designs or specifications of such products at any time without notice. Emerson does not assume responsibility for the selection, use or maintenance of any product.