Product Care And Maintenance - HoMedics SCAN-1 Instruction Manual And Warranty Information

2. Assemble ottoman support legs to base
• Align support legs (D) to ottoman base (C) with the brackets
facing inward towards each other. (Fig 4.)
• Flip ottoman base on its side and insert one washer (M)
per available hole in the base of the ottoman.
• Insert two bolts (P) up through the washers and into the
support legs (Fig 5.) and tighten slightly, partially securing
the base and the support legs.
• Turn the ottoman base to the opposite side and repeat
the previous two steps.
• Tighten all four screws with small wrench (N).
3. Assemble ottoman cushion to support base
• Lay cushion on a clean surface with the screw holes facing
up. Flip the support legs over so that the brackets line up
with the screw holes on the cushion.
• Align cushion so the slope of the cushion matches the
slope of the support legs. (Fig 6.)
• Line up the support brackets with the screw holes in
the cushion.
• Insert four screws (I) into the bottom and slightly tighten
into place.
• Tighten all four screws completely with the wrench (N).
4. Connect power source
• To supply power to the back cushion and seat you must
connect the two power supply plugs to each other.
• Locate the output jack on the lower left hand side of the
back cushion and the input jack just under the back left
side of the seat cushion. (Fig 7a.)
• Line up the arrows on both jacks and connect to each
other. (Fig 8.)
• Now you are ready to connect the power supply from the
recliner to the ottoman.
• Locate the output jack in the left underside of the seat
cushion and the input jack on the underside of the
ottoman. (Fig 7b.)
• Line up the arrows on both jacks and connect both
adaptors to each other. (Fig 8.)
• Now the back cushion, seat cushion and ottoman are
connected and able to communicate with the hand control.
Figure 4
Figure 5
Figure 6
6
• The last step is to connect the main power supply into
the wall outlet.
• Locate the adaptor jack on the back side of the back cushion
and connect it to the adaptor jack that came with this recliner.
(Fig 9.)
• Once connected, plug the other end into an AC adaptor
into a power outlet. Use only the AC power adaptor
provided with this unit.
See pages 10 – 11 for operating instructions.
Product Care & Maintenance
To Clean
• Disconnect the recliner from power source before cleaning.
• A soft, damp cloth may be used for the recliner. When cleaning
the controller or around the power switch, use a dry cloth only.
• Dust may be removed from the backrest or armrest with
a vacuum.
• Do not use abrasive cleaners, brushes, gasoline, kerosene, polish
or paint thinner to clean.
• The cushions are not machine washable. Do not immerse
in liquids to clean.
To Store
• Place the controller in its specially designed pocket on the left
side of the recliner.
• Avoid contact with sharp edges or pointed objects which might
damage/puncture the fabric.
• Do not store near heat or open flame. Do not leave this product
exposed to direct sunlight for long periods of time. This may
cause fading.
• It is recommended that the recliner be covered when not
in use for long periods of time.
• It is suggested that the power cord be coiled and the unit
kept in an area free of dust and moisture if not in use for long
periods of time
Frame:
• Periodically, the frame should be checked to ensure the screws
are tight. If the frame is found to be loose, tighten screws with the
tools provided.
The Scandinavian recliner and massage cushion are designed for
indoor applications only. Use of this product for outdoor applications
may cause irreparable damage and void your warranty.
Figure 7a
Figure 7b
Figure 8
Figure 9
7