Download Print this page

Advertisement

Quick Links

Models:
AT-Supreme
WARNING
IF THE INFORMATION IN
THESE INSTRUCTIONS IS NOT
FOLLOWED EXACTLY, A FIRE
OR EXPLOSION MAY RESULT
CAUSING PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.
- Do not store or use gasoline or other
flammable vapors and liquids in the
vicinity of this or any other appliance.
- What to do if you smell gas
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier
from a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier,
call the fire department.
- Installation and service must be
performed by a qualified installer,
service agency, or the gas supplier.
Printed in U.S.A.
Copyright 1997,
Heat-N-Glo Fireplace Products, Inc.
6665 West Highway 13, Savage, MN 55378
Heat-N-Glo Fireplace
READ THIS MANUAL BEFORE
INSTALLING OR OPERATING THIS
APPLIANCE. THIS INSTALLERS GUIDE
MUST BE LEFT WITH APPLIANCE FOR
FUTURE REFERENCE.
WARNING: IMPROPER
INSTALLATION, ADJUSTMENT,
ALTERATION, SERVICE OR
MAINTENANCE CAN CAUSE
INJURY OR PROPERTY DAMAGE.
REFER TO THIS MANUAL. FOR
ASSISTANCE OR ADDITIONAL
INFORMATION CONSULT A
QUALIFIED INSTALLER, SERVICE
AGENCY, OR THE GAS SUPPLIER.
1.
2. This appliance is only for use with the
Please contact your Heat-N-Glo Fireplace dealer for any
questions or concerns. For the number of your nearest
Heat-N-Glo dealer, please call 612-890-8367.
Installers Guide
Underwriters Laboratories Listed
This appliance may be installed in an
aftermarket, permanently located,
manufactured (mobile) home, where
not prohibited by local codes.
type of gas indicated on the rating
plate. This appliance is not convertible
for use with other gases, unless a
certified kit is used.
Patents Pending
438-982-A 12/97

Advertisement

loading

Summary of Contents for Heat-N-Glo AT-Supreme

  • Page 1 Printed in U.S.A. Please contact your Heat-N-Glo Fireplace dealer for any questions or concerns. For the number of your nearest Copyright 1997, Heat-N-Glo dealer, please call 612-890-8367.
  • Page 2: Safety And Warning Information

    SAFETY AND WARNING INFORMATION READ and UNDERSTAND all instructions carefully before starting the installation. FAILURE TO FOLLOW these installation instructions may result in a possible fire hazard and will void the warranty. Prior to the first firing of the fireplace, READ the Using Your Fireplace section of the Owners Guide.
  • Page 3 Table of Safety and Warning Information ....i Contents Section 1: Approvals and Codes ....1 Section 2: Getting Started......2 Section 3: Installing the Insert ..... 5 Section 4: Maintenance and Servicing ..19 Section 5: Replacement Parts and Accessories ......... 21...
  • Page 4 Approval Listings Appliance Certification and Codes Installers Guide Z21.44•CGA2.19/IR#41 Approvals and Codes Installation Codes High Altitude Installations...
  • Page 5 Introducing the Heat-N-Glo Gas Appliances Installers Guide Getting Pre-installation Started Preparation Installers Guide...
  • Page 6 VENTING AND INSTALLATION...
  • Page 7: Minimum Fireplace Size

    MINIMUM FIREPLACE SIZE FRONT WIDTH : 29 ” (750mm) REAR WIDTH : 20 ” (521mm) TOP VIEW DEPTH : 13” (331mm) HEIGHT : 20” (508mm) NOTE: If exhaust collar on insert and fireplace damper do not line up, add 4 inches (102mm) to minimum fireplace height for bends in vent pipe.
  • Page 8 Step 1 Installing the Vent System Installing the Insert...
  • Page 9 CAUTION TO AVOID DOWNDRAFTS AND/OR COLD AIR PROBLEMS, IT IS RECOMMENDED TO SEAL OFF THE AREA BETWEEN THE TERMINATION CAP AND THE TOP OF THE SOLID-FUEL CHIMNEY OPENING INTO WHICH THE VENT CAP HAS BEEN INSTALLED. WHEN USING THE LINK-DV4-3O VENT SYSTEM, IT IS REQUIRED TO SEAL AROUND THE FLEXIBLE VENT PIPES IN THE DAMPER AREA.
  • Page 10 Termination Cap...
  • Page 11 This option shows both exhaust and TERMINATION CAP inlet air ventpipes attached the adaptor. ADAPTOR EXHAUST VENT PIPE V= 14FT. MINIMUM 50FT. MAXIMUM WARNING: Do not block pipe end with insullation or any other sealing material. INLET AIR VENT PIPE...
  • Page 12 INLET AIR STARTING COLLAR EXHAUST STARTING COLLAR...
  • Page 13 Step 2 Positioning, Leveling, and Securing the Insert Step 3 The Gas Control Systems STANDING PILOT 3/8" (10 mm)
  • Page 14 Step 4 The Gas Supply Line USE A WRENCH ON USE A WRENCH ON SHUT-OFF VALVE WHEN SHUT-OFF VALVE WHEN TIGHTENING GAS LINE. TIGHTENING GAS LINE. MANUAL SHUT-OFF MANUAL SHUT-OFF VALVE VALVE ACCESS GAS VALVE FLEX CONNECTOR...
  • Page 15: Gas Pressure Requirements

    Step 5 Gas Pressure Requirements Step 6 Wiring the Fireplace DISCONNECT REMOTE CONTROLS IF YOU ARE ABSENT FOR EXTENDED TIME PERIODS. THIS WILL PREVENT ACCIDENTAL APPLIANCE OPERATION. For Standing Pilot Ignition Wiring...
  • Page 16 CAUTION LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS. WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION. VERIFY PROPER OPERATION AFTER SERVICING.
  • Page 17: Installing Logs

    FAN WIRING DIAGRAM NOTE: IF ANY OF THE ORIGINAL WIRE NOTE: IF ANY OF THE ORIGINAL WIRE VARIABLE SPEED CONTROL AS SUPPLIED WITH THE APPLIANCE AS SUPPLIED WITH THE APPLIANCE MUST BE REPLACED, IT MUST BE MUST BE REPLACED, IT MUST BE REPLACED WITH TYPE 105 DEGREE C REPLACED WITH TYPE 105 DEGREE C RATED WIRE.
  • Page 18 GLASS DOOR EMBER MATERIAL...
  • Page 19 Step 8 Installing Trim Surrounds FIREBOX SURROUND SURROUND WITH TRIM TRIM DOOR ON/OFF SWITCH VOLTAGE WIRES Figure 12...
  • Page 20 12” MAX. MANTEL 12” MAX. TOP OF UNIT Figure 13...
  • Page 21 Step 9 Before Lighting the Appliance Installers Guide Step 10 Lighting the Appliance After the After the Installation Installation...
  • Page 22 Appliance Maintenance IMPORTANT TURN OFF THE GAS BEFORE SERVICING YOUR FIREPLACE. Maintaining Type of Servicing Fireplace Fireplace Maintenance Task To Maintenance Frequency Be Completed Your Appliance Replacing Once annually, Qualified Brush away loose ember material near Old Ember during the Service the burner.
  • Page 23 MAKE SURE THE FLAMES ARE STEADY—NOT LIFTING OR FLOATING. STANDING PILOT 3/8" (10 mm)