Azden PRO-XR Instruction Manual page 2

CAUTION: DO NOT STORE OR OPERATE THIS PRODUCT NEAR A HEAT SOURCE OR IN AN ENVIRONMENT OF EXTREME TEMPERATURES.
AVOID EXPOSURE TO RAIN OR ANY OTHER SOURCE OF MOISTURE. DO NOT SUBMERGE IN WATER. IF EXTERIOR IS EXPOSED TO WATER,
WIPE DRY BEFORE USE. DO NOT ATTEMPT TO OPEN THE CASING OR MAKE ANY MODIFICATION TO THE INTERNAL ELECTRICAL
COMPONENTS. ELECTRIC SHOCK OR INJURY MAY RESULT. ANY UNAUTHORIZED MODIFICATION TO THIS PRODUCT WILL VOID ANY
APPLICABLE WARRANTIES.
The PRO-XR 2.4 GHz Wireless Microphone System is certified for legal operation in the United States of America, Canada, and all EU member
countries. Use of the PRO-XR may or may not be allowed in other countries. It is the responsibility of the user to check the local wireless frequency
regulations of any country outside of the previously stated certified countries.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate this equipment. (Example - use only shielded interface cables when connecting to computer or peripheral devices).
Radiation Exposure Statement
This equipment complies with FCC RF and IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 0.5 centimeters between the radiator and your body. This transmitter must not be co-located or
operating in conjunction with any other antenna or transmitter. The antennas used for this transmitter must be installed to provide a separation distance
of at least 0.5 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.
This device complies with Part 15 of the FCC Rules and with RSS-247 of the Industry Canada Rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
1. Attach one of the included
antennas to the transmitter by
screwing it to the antenna
threads on top.
2. Plug the EX-507XR lapel
microphone into the
transmitter's (TX) Microphone
Input located on top.
3. Turn on both the receiver (RX)
and transmitter (TX) units by
pressing and holding down the
power button for 1 second. The
units should pair automatically,
and each show 2 solid green
lights.
You're ready to start shooting video with your PRO-XR 2.4 GHz Wireless Microphone System!
ADVISORY
QUICK START GUIDE
4. Mount the receiver (RX) to your camera: slide
5. Connect the MIC OUT of the receiver (RX)
Keep reading for more detailed instructions.
2
the shoe mount into the camera's shoe slot,
and tighten the thumb wheel.
to your camera's microphone input using
the included Audio Output Cable.