Lower Blade Guard - DeWalt DCS577 Manual

EngliSh
To Remove Knockout

WARNING: ALWAYS use eye protection. All users and
bystanders must wear eye protection that conforms to
ANSI Z87.1.

WARNING: Make sure that bevel adjusting locking lever
is tight and secure after using it to remove knockout. If
blade adjustment shifts while cutting it may cause binding
and kickback.
Place the round centre hole of the blade into the notch
the top of the bevel adjustment lever
blade firmly, pull until the knockout pops out. The diamond-
shaped arbor centre is now exposed.
To Install the Blade (Fig. A, M, N)
1. Loosen and remove the blade clamping screw
wrench 21 provided, by turning it clockwise as indicated by
the arrow on the outer clamp washer
2. Remove outer clamp washer
3. Using the lower blade guard retracting lever
lower blade guard .
6
iMPORTAnT: When retracting the lower blade guard to
install the blade, check the condition and operation of the
lower blade guard to assure that it is working properly. Make
sure it moves freely and does not touch the blade, foot plate
or any other part, in all angles and depths of cut.
4. Place blade 28 on saw spindle
washer 30 , making sure that the blade will rotate in the
proper direction (the direction of the rotation arrow on the
saw blade and the teeth must point in the same direction as
the direction of rotation arrow on the lower blade guard).
iMPORTAnT: Always ensure the diamond-shaped arbor
centre of the blade aligns with the raised diamond-shaped
arbor centre on the outer clamp washer.
nOTE: Do not assume that the printing on the saw blade will
always be facing you when properly installed.
5. Place outer clamp washer
large flat surface against the blade and the wording on the
outer clamp washer facing you as shown in Figure N.
6. Thread the blade clamping screw
hand (screw has left-hand threads and must be turned
counterclockwise to tighten).
7. Slowly release the lower blade guard retracting lever
8. Depress the spindle lock button
spindle with the blade wrench provided until the blade
lock engages and the blade stops rotating. Using the blade
wrench, firmly tighten blade clamping screw.
NOTICE: Never engage the blade lock while saw is
running, or engage in an effort to stop the tool. Never
turn the saw on while the blade lock is engaged. Serious
damage to your saw will result.
To Replace the Blade (Fig. A, N)
1. Depress the spindle lock button
spindle with the blade wrench provided until the blade lock
engages and the blade stops rotating.
2. With the blade wrench provided
clamping screw 19 by turning it clockwise as indicated by
the arrow on the outer clamp washer
16
25 on
9 . Grasping the saw and
19 with the
27 .
27 .
4 , retract the
29 against the inner clamp
on saw spindle with the
27 29
19 into saw spindle by
4 .
11 while turning the saw
11 while turning the saw
21 , loosen the blade
.
27
3. Remove the outer clamp washer
4. Using the lower blade guard retracting lever
lower blade guard. Remove used blade and properly discard.
5. Install new blade as previously described.
6. Clean any sawdust that may have accumulated in the guard
or clamp washer area. Check the condition and operation
of the lower blade guard as previously outlined. Do not
lubricate this area.
7. Select the proper blade for the application (refer to Blades).
Always use blades that are the correct size (190 mm
diameter) with the proper size and shape centre hole
for mounting on the saw spindle. Always assure that the
maximum recommended speed (rpm) on the saw blade
meets or exceeds the speed (rpm) of the saw.

Lower Blade Guard


WARNING: The lower blade guard is a safety feature
which reduces the risk of serious personal injury.
Never use the saw if the lower guard is missing,
damaged, misassembled or not working properly.
Do not rely on the lower blade guard to protect you
under all circumstances. Your safety depends on
following all warnings and precautions as well as
proper operation of the saw. Check lower guard for
proper closing before each use as outlined in Safety
Instructions for All Saws. If the lower blade guard
is missing or not working properly, have the saw
serviced before using. To assure product safety and
reliability, repair, maintenance and adjustment
should be performed by an authorised service centre
or other qualified service organisation, always using
identical replacement parts.
Blades

WARNING: To minimise the risk of eye injury, always
use eye protection. Carbide is a hard but brittle material.
Foreign objects in the workpiece such as wire or nails
can cause tips to crack or break. Only operate saw when
proper saw blade guard is in place. Mount blade securely
in proper rotation before using, and always use a clean,
sharp blade.
Do not use abrasive wheels or blades. A dull blade will cause
slow, inefficient cutting resulting in overload to the saw motor,
excessive splintering and could increase the possibility of
kickback. Please refer to the following table to determine the
correct size replacement blade for your model saw.
DCS577
Blade Diameter Teeth
DT40270 190 mm 24
DT40271 190 mm 36
Kickback
Kickback is a sudden reaction to a pinched, bound or misaligned
saw blade, causing an uncontrolled saw to lift up and out of the
workpiece toward the operator. When the blade is pinched or
.
27
4 , retract the
Application
General purpose wood cutting
Plywood cutting