Planet WNAP-W2200UE User Manual
  1. Manuals
  2. Brands
  3. Planet Manuals
  4. Wireless Access Point
  5. WNAP-W2200UE
  6. User manual

Planet WNAP-W2200UE User Manual

300mbps 802.11n in-wall wireless ap w/usb charger
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
300Mbps 802.11n
In-Wall Wireless AP
w/ USB Charger
WNAP-W2200UE

Advertisement

Table of Contents
loading

Related Manuals for Planet WNAP-W2200UE

Summary of Contents for Planet WNAP-W2200UE

  • Page 1 300Mbps 802.11n In-Wall Wireless AP w/ USB Charger WNAP-W2200UE...
  • Page 2 Copyright Copyright  2018 by PLANET Technology Corp. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of PLANET.
  • Page 3 FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for an uncontrolled environment. In order to avoid the possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna shall not be less than 20 cm (8 inches) during normal operation. CE Compliance Statement This device meets the RED 2014/53/EU requirements on the limitation of exposure of the general public to electromagnetic fields by way of health protection.
  • Page 4 Revision User Manual of PLANET 300Mbps 802.11n In-Wall Wireless Access Point w/ USB Charger Model: WNAP-W2200UE Rev: 1.0 (October, 2018) Part No. EM-WNAP-W2200UE_v1.0...

  • Page 5: Table Of Contents

    Chapter 6.Quick Connection to a Wireless Network ............... 41 Windows XP (Wireless Zero Configuration) ..............41 Windows 7 (WLAN AutoConfig) ..................43 Mac OS X 10.x ........................46 iPhone/iPod Touch/iPad ....................51 Appendix A: Planet Smart Discovery Utility ..................55 Appendix B: FAQs ..........................56...
  • Page 6 Q1: How to Set Up the AP Client Connection ................56 Q2: How to Set Up the WDS Connection ................. 61 Appendix B: Troubleshooting ......................65 Appendix C: Glossary ......................... 67...
  • Page 7 FIGURE 2-1 WNAP-W2200UE T ......................8 IGURE RIPLE 2-2 WNAP-W2200UE F ......................9 IGURE RONT ANEL 2-3 WNAP-W2200UE R ......................9 IGURE ANEL ........................11 IGURE TAKING THE COVER OFF 3-2 C ....................12 IGURE ONNECTING THE THERNET CABLE 3-3 C ................

  • Page 8: Igure 2-1 Wnap-W2200Ue Triple View

    5-31 S ............................40 IGURE YSTEM 5-32 U ..............................40 IGURE 6-1 S – W ..................41 IGURE YSTEM IRELESS ETWORK 6-2 C ....................41 IGURE HOOSING A IRELESS ETWORK 6-3 E ......................42 IGURE NTERING THE ETWORK 6-4 C -- C ................

  • Page 9: Chapter 1.Product Introduction

    User Manual of WNAP-W2200UE Chapter 1. Product Introduction Package Contents Thank you for choosing PLANET WNAP-W2200UE Wireless AP. Please verify the contents inside the package box. Package Contents of WNAP-W2200UE WNAP-W2200UE Quick Guide Screw x 2 If there is any item missing or damaged, please contact the seller immediately.

  • Page 10: Product Description

    VLAN and PLANET AP controller. Furthermore, it conforms to standard 86-type electrical junction box and IEEE 802.3af/at+, suitable for in-wall installation enabling to integrate the hotel network with its all-in-one interface. The WNAP-W2200UE also provides stable wireless signal that makes access to internet viable in regard to whatever nature of work you are into.
  • Page 11 Suitable for Any Room Installation without Spoiling Interior Design Featuring attractive in-wall design, the WNAP-W2200UE can be firmly installed into the wall via the standard 86 x 86 m m European outlet box, which makes electrical wiring invisible and convenient for room installation without affecting the original interior design.
  • Page 12 Having a good night sleep is what we need in the hotel. It is easy to disable the Wi-Fi signal and LED on the front panel of the WNAP-W2200UE. When you don’t need to use wireless LAN, just press the button to close the Wi-Fi and LE D.

  • Page 13: Product Features

    Real-time Wi-Fi channel analysis chart and client limit control for better performance   Easy Deployment and Management Supports PLANET AP Controllers in AP mode  Easy discovery by PLANET Smart Discovery  Self-healing mechanism through system auto reboot setting ...

  • Page 14: Product Specifications

    User Manual of WNAP-W2200UE Product Specifications WNAP-W2200UE Product 300Mbps 802.11n In-Wall Wireless Access Point with USB Charger Hardware Specifications 1 x 10/100BASE-TX RJ45 port Auto-negotiation and auto MDI/MDI-X 1 x 10/100Mbps auto MDI/MDI-X RJ45 port (rear panel) Interfaces PoE Port ※...
  • Page 15 VLAN SSID-to-VLAN mapping to up to 4 SSIDs Supports auto reboot settings per day/hour Self-healing Supports PLANET Hardware AP Controller/ Software AP Controller Applicable controllers: WAPC-500, WAPC-1000, and SAPC Remote management through PLANET DDNS/Easy DDNS Configuration backup and restore System Management...

  • Page 16: Chapter 2.Hardware Installation

    User Manual of WNAP-W2200UE Chapter 2. Hardware Installation Product Outlook WNAP-W2200UE Dimensions: 86 x 35 x 86 mm (W x D x H)  Weight: 106 ±5g   Triple View Figure 2-1 WNAP-W2200UE Triple View...

  • Page 17: Figure 2-2 Wnap-W2200Ue Front Panel

    User Manual of WNAP-W2200UE  Front Panel Figure 2-2 WNAP-W2200UE Front Panel  Rear Panel Figure 2-3 WNAP-W2200UE Rear Panel...
  • Page 18 User Manual of WNAP-W2200UE  State Description The LED indicates green color Wi-Fi  Button definition Object Description Press the button for one second to turn Wi-Fi on or off Wi-Fi Press the Reset button for over 15 seconds and then release it to restore Reset system to the factory default settings.

  • Page 19: Chapter 3.Connecting To The Ap

    If there is any problem, please contact your local ISP. Step 1. Follow the figure below to install the WNAP-W2200UE. Use the flat-blade screwdriver to take the cover of the WNAP-W2200UE off. Figure 3-1 Taking the Cover Off...

  • Page 20: F Igure 3-2 C Onnecting The E Thernet Cable

    User Manual of WNAP-W2200UE Step 2. Follow the figure below to install the WNAP-W2200UE. Figure 3-2 Connecting the Ethernet cable Step 3. Follow the figure below to connect the network devices. Figure 3-3 Connecting the Laptop or Charging Device -12-...

  • Page 21: Chapter 4.Quick Installation Guide

    These values can be changed as you want. In this guide, we use all the default values for description. Connect the WNAP-W2200UE with your PC by an Ethernet cable plugging in LAN port on one side and in LAN port of PC on the other side. Please power on the WNAP-W2200UE by PoE switch through the PoE port.

  • Page 22: Figure 4-1 Tcp/Ip Setting

    User Manual of WNAP-W2200UE Figure 4-1 TCP/IP Setting Now click OK to save your settings. Now, you can run the ping command in the command prompt to verify the network connection between your PC and the AP. The following example is in Windows 10 OS. Please follow the steps below: Click on Start >...

  • Page 23: F Igure 4-3 S Uccessful R Esult Of P Ing C Ommand

    User Manual of WNAP-W2200UE Figure 4-2 Windows Start Menu Open a command prompt, type ping 192.168.1.253 and then press Enter. If the result displayed is similar to 4-3, it means the connection between your PC and the AP Figure has been established well.

  • Page 24: Figure 4-4 Failed Result Of Ping Command

    User Manual of WNAP-W2200UE If the result displayed is similar to 4-4, it means the connection between your PC and the AP Figure has failed. Figure 4-4 Failed Result of Ping Command If the address is 0.0.0.0, check your adapter installation, security settings, and the settings on your AP. Some firewall software programs may block a DHCP request on newly installed adapters.

  • Page 25: Starting Setup In The Web Ui

    User Manual of WNAP-W2200UE Starting Setup in the Web UI It is easy to configure and manage the AP with the web browser. To access the configuration utility, open a web-browser and enter the default IP address Step 1. http://192.168.1.253 in the web address field of the browser.

  • Page 26: Chapter 5.Configuring The Ap

    Chapter 5. Configuring the AP This chapter delivers a detailed presentation of AP’s functionalities and features 3 main items below, allowing you to manage the AP with ease. The screenshots use the WNAP-W2200UE as an example. Figure 5-1 Main Menu...

  • Page 27: Wizard

    User Manual of WNAP-W2200UE Wizard The Wizard guides you to configuring the WNAP-W2200UE in a different mode, including Gateway, Repeater, AP and Super WDS mode. Figure 5-2 Operation Mode The default operation mode is AP Mode. -19-...

  • Page 28: Gateway Mode (Router)

    User Manual of WNAP-W2200UE Gateway Mode (Router) Click “Wizard”  “Gateway Mode” and the following page will be displayed. This section allows you to configure the Gateway mode. Figure 5-3 Gateway Mode -20-...

  • Page 29: Wan Settings

    User Manual of WNAP-W2200UE 5.2.1 WAN Settings Static IP If your ISP offers you static IP Internet connection type, select “Static IP" and then enter IP address, subnet mask, default gateway and primary DNS information provided by your ISP in the corresponding fields.

  • Page 30: Wireless

    User Manual of WNAP-W2200UE DHCP Choose “DHCP” and the router will automatically obtain IP addresses, subnet masks and gateway addresses from your ISP. Figure 5-6 Gateway – DHCP 5.2.2 Wireless Figure 5-7 Gateway – Wireless The page includes the following fields:...

  • Page 31: Repeater Mode (Universal Repeater)

    User Manual of WNAP-W2200UE Repeater Mode (Universal Repeater) Click “Wizard”  “Repeater Mode” and the following page will be displayed. This section allows you to configure the Repeater mode. Figure 5-8 Repeater Mode -23-...
  • Page 32 User Manual of WNAP-W2200UE The page includes the following fields: Object Description Enter the root AP’s SSID or press “Scan AP” to select. Repeater SSID Check to lock the root AP MAC address. Lockmac Select the wireless encryption of root AP.
  • Page 33 User Manual of WNAP-W2200UE Select the authentication and bandwidth which are the same as root AP to establish the connection. Figure 5-10 Repeater Mode -- Select AP -25-...

  • Page 34: Ap Mode

    User Manual of WNAP-W2200UE AP Mode In the AP mode, the AP wireless interface and cable interface bridge together. Click “Wizard”  “AP Mode” and the following page will be displayed. This section allows you to configure the AP mode.

  • Page 35: Ap Mode -- Lan

    User Manual of WNAP-W2200UE The page includes the following fields: Object Description Select “ON” or “OFF” to enable or disable 2.4G or 5.8G wireless LAN. WLAN Press the button to check your wireless environment. Wireless Analyzer Status SSID It is the wireless network name. The default SSID is “PLANET_2.4G”.

  • Page 36: Super Wds Mode (Wds Bridge In Ptp/Ptmp)

    User Manual of WNAP-W2200UE Super WDS Mode (WDS Bridge in PtP/PtMP) In the Super WDS mode, the wireless interface can be connected with other wireless APs through WDS, and the wireless interface and c able interface. Click “Wizard”  “Super WDS Mode” and the following page will be displayed.
  • Page 37 User Manual of WNAP-W2200UE AP1 enters the MAC address of AP2. And AP2 enters the MAC address of AP1. Then select the same Channel to establish the connection. Figure 5-14 Super WDS Mode – AP1 Figure 5-155 Super WDS Mode – AP2...

  • Page 38: Advanced

    User Manual of WNAP-W2200UE Advanced Figure 5-166 Advanced 5.6.1 Device Status 5.6.1.1. Status Figure 5-177 Status The page includes the following fields: Object Description Software Version It shows the firmware version of AP. It shows the hardware version of AP.

  • Page 39: Lan Status

    User Manual of WNAP-W2200UE 5.6.1.2. 2.4G Status Figure 5-188 Wireless Status The page includes the following fields: Object Description It shows the wireless status is Enable or Disable. 2.4G / 5.8G Wireless Status It shows the SSID of the AP. Default is PLANET_2.4G.

  • Page 40: Wireless

    User Manual of WNAP-W2200UE The page includes the following fields: Object Description It shows the IP of the AP. Default is 192.168.1.253. LAN IP It shows the subnet mask of the AP. Default is 255.255.255.0. Subnet Mask It shows the MAC address of the LAN por.t 5.6.2 Wireless...

  • Page 41: F Igure 5-21 V Irtual Ap

    User Manual of WNAP-W2200UE 5.6.2.2. Virtual AP Figure 5-21 Virtual AP The page includes the following fields: Object Description It shows the wireless status is ON or OFF. Wireless Status It shows the SSID of the AP. Default is PLANET_2.4G_1.

  • Page 42: F Igure 5-23 A Ccess C Ontrol – A Llow L Isted

    User Manual of WNAP-W2200UE Figure 5-23 Access Control – Allow Listed The page includes the following fields: Object Description Select MAC Access All, Allow Listed or Deny Listed. Access Control Enter the MAC address that you need to allow or deny access.
  • Page 43 User Manual of WNAP-W2200UE The page includes the following fields: Object Description It shows FCC or ETSI depending on the firmware. Regional Select 802.11N/G or 802.11B/G in 2.4G AP. Mode The range of transmit power is 100%, 75%, 50%, 25% or 12.5%. In...

  • Page 44: Network

    User Manual of WNAP-W2200UE 5.6.3 Network 5.6.3.1. LAN Settings Figure 5-25 LAN Settings The page includes the following fields: Object Description Enter an IP address of LAN. Enter a subnet mask of LAN. Subnet Mask 5.6.3.2. VLAN Figure 5-26 VLAN...

  • Page 45: Management

    User Manual of WNAP-W2200UE 5.6.3.3. SNMP Figure 5-27 SNMP The page includes the following fields: Object Description Enter the read community, default is public Read Community Enter the write community, default is private Write Community Enter the SNMP trap IP address, default is 192.168.1.1 Trap Destination Address 5.6.4 Management...

  • Page 46: Figure 5-29 Log

    User Manual of WNAP-W2200UE 5.6.4.2. Signal Tracking The page includes the following fields: Object Description SSID Select the SSID you need to check by pressing the Scan AP button It shows the MAC address of the tracked AP It shows the signal strength of the AP Signal Strength 5.6.4.3.

  • Page 47: F Igure 5-30 U Pgrading F Irmware

    User Manual of WNAP-W2200UE The page includes the following fields: Object Description Enable remote log server Remote Log Server Enter the IP of remote log server Press to refresh the system log Refresh Clear Press to clear the system log 5.6.4.4.
  • Page 48 User Manual of WNAP-W2200UE 5.6.4.5. System Figure 5-311 System The page includes the following fields: Object Description Press to back up the configuration Backup Press to select the configuration file Choose File Press to restore the configuration Restore Press to reset the device to default...

  • Page 49: Chapter 6.Quick Connection To A Wireless Network

    User Manual of WNAP-W2200UE Chapter 6. Quick Connection to a Wireless Network In the following sections, the default SSID of the WNAP-W2200UE is configured to “default”. Windows XP (Wireless Zero Configuration) Step 1: Right-click on the wireless network icon displayed in the system tray Figure 6-1 System Tray –...
  • Page 50 User Manual of WNAP-W2200UE Step 4: Enter the encryption key of the wireless AP (1) The Wireless Network Connection box will appear (2) Enter the encryption key that is configured in section 5.7.2.1 (3) Click the [Connect] button Figure 6-3 Entering the Network Key Step 5: Check if “Connected”...

  • Page 51: Windows 7 (Wlan Autoconfig)

    User Manual of WNAP-W2200UE Windows 7 (WLAN AutoConfig) WLAN AutoConfig service is built-in in Windows 7 that can be used to detect and connect to wireless network. This built-in wireless network connection tool is similar to wireless zero configuration tool in Windows XP.
  • Page 52 User Manual of WNAP-W2200UE Step 4: Enter the encryption key of the wireless AP (1) The Connect to a Network box will appear. (2) Enter the encryption key that is configured in section 5.7.2.1 (3) Click the [OK] button. Figure 6-7 Typing the Network Key...
  • Page 53 User Manual of WNAP-W2200UE Step 5: Check if “Connected” is displayed. Figure 6-9 Connected to a Network -45-...

  • Page 54: Mac Os X 10.X

    User Manual of WNAP-W2200UE Mac OS X 10.x In the following sections, the default SSID of the WNAP-W2200UE is configured to “default”. Step 1: Right-click on the network icon displayed in the system tray The AirPort Network Connection menu will appear.
  • Page 55 User Manual of WNAP-W2200UE Step 4: Enter the encryption key of the wireless AP (1) Enter the encryption key that is configured in section 5.7.2.1 (2) Click the [OK] button. Figure 6-12 Entering the Password If you will be connecting to this Wireless AP in the future, check [Remember this network].
  • Page 56 User Manual of WNAP-W2200UE Step 5: Check if the AirPort is connected to the selected wireless network. If “Yes”, then there will be a “check” symbol in front of the SSID. Figure 6-13 Connected to the Network -48-...
  • Page 57 User Manual of WNAP-W2200UE There is another way to configure the MAC OS X wireless settings: Step 1: Click and open the [System Preferences] by going to Apple > System Preference or Applications Figure 6-14 System Preferences Step 2: Open Network Preference by clicking on the [Network] icon...
  • Page 58 User Manual of WNAP-W2200UE Step 3: Check Wi-Fi setting and select the available wireless network (1) Choose the AirPort on the left menu (make sure it is ON) (2) Select Network Name [default] here If this is the first time to connect to the Wireless AP, it should show “No network selected”.

  • Page 59: Iphone/Ipod Touch/Ipad

    User Manual of WNAP-W2200UE iPhone/iPod Touch/iPad In the following sections, the default SSID of the WNAP-W2200UE is configured to “default”. Step 1: Tap the [Settings] icon displayed in the home screen Figure 6-17 iPhone – Settings icon Step 2: Check Wi-Fi setting and select the available wireless network...
  • Page 60 User Manual of WNAP-W2200UE Figure 6-19 Wi-Fi Setting – Not Connected Step 3: Tap the target wireless network (SSID) in “Choose a Network…” (1) Turn on Wi-Fi by tapping “Wi-Fi” (2) Select SSID [default] Figure 6-20 Turning on Wi-Fi -52-...
  • Page 61 User Manual of WNAP-W2200UE Step 4: Enter the encryption key of the Wireless AP (1) The password input screen will be displayed. (2) Enter the encryption key that is configured in section 5.7.2.1 (3) Tap the [Join] button. Figure 6-21 iPhone -- Entering the Password...
  • Page 62 User Manual of WNAP-W2200UE Step 5: Check if the device is connected to the selected wireless network. If “Yes”, then there will be a “check” symbol in front of the SSID. Figure 6-22 iPhone -- Connected to the Network -54-...

  • Page 63: Appendix A: Planet Smart Discovery Utility

    User Manual of WNAP-W2200UE Appendix A: Planet Smart Discovery Utility To easily list the WNAP-W2200UE in your Ethernet environment, the Planet Smart Discovery Utility is an ideal solution. The following installation instructions guide you to running the Planet Smart Discovery Utility.

  • Page 64: Appendix B: Faqs

    User Manual of WNAP-W2200UE Appendix B: FAQs Q1: How to Set Up the AP Client Connection Topology: Step 1. Use static IP in the PCs that are connected with AP-1(Site-1) and AP-2(Site-2). In this case, Site-1 is “192.168.1.100”, and Site-2 is “192.168.1.200”.
  • Page 65 User Manual of WNAP-W2200UE Step 2. In AP-2, change the default IP to the same IP range but different from AP-1. In this case, the IP is changed to 192.168.1.252. Step 3. In AP-1, go to “Wizard” to configure it to AP Mode. In AP-2, configure it to Repeater Mode.
  • Page 66 User Manual of WNAP-W2200UE Step 4. In AP-2, press Scan AP to search the AP-1. You can also enter the MAC address, SSID, encryption and bandwidth if you know what they are. Note. WDS passthrough should be if the root AP is the different model from client AP.
  • Page 67 User Manual of WNAP-W2200UE Step 7. Use command line tool to ping each other to ensure the link is successfully established. From Site-1, ping 192.168.1.200, and in Site-2, ping 192.168.1.100. Step 8. Configure the TCP/IP settings of Site-2 to “Obtain an IP address automatically”.
  • Page 68 User Manual of WNAP-W2200UE Step 9. Use command line tool to ping the DNS (e.g., Google) to ensure Site-2 can access internet through the wireless connection. The following hints should be noted: The encryption method must be the same as that of both sites if configured.

  • Page 69: Q2: How To Set Up The Wds Connection

    User Manual of WNAP-W2200UE Q2: How to Set Up the WDS Connection Topology: Step 1. Use static IP in the PCs that are connected with WNAP-W2200UE-1 (Site-1) and WNAP-W2200UE-2 (Site-2). In this case, Site-1 is “192.168.1.100”, and Site-2 is “192.168.1.200”. -61-...
  • Page 70 User Manual of WNAP-W2200UE Step 2. In AP-2, change the default IP to the same IP range but different from AP-1. In this case, the IP is changed to 192.168.1.252. Step 3. In AP-2, go to “Wizard” to configure it in Super WDS Mode.
  • Page 71 User Manual of WNAP-W2200UE Step 5. Click “Apply” to finish the setting. Step 6. Click “Return home” to check WDS status. Step 7. In AP-1, repeat step 3 to step 6 for WDS setting. -63-...
  • Page 72 User Manual of WNAP-W2200UE Step 8. Use command line tool to ping each other to ensure the link is successfully established. From Site-1, ping 192.168.1.200, and in Site-2, ping 192.168.1.100. The following hints should be noted: The encryption method must be the same as that of both sites if configured.

  • Page 73: Appendix B: Troubleshooting

    User Manual of WNAP-W2200UE Appendix B: Troubleshooting If you find the AP is working improperly or stop responding to you, please read this troubleshooting first before contacting the dealer for help. Some problems can be solved by yourself within a very short time.
  • Page 74 User Manual of WNAP-W2200UE Scenario Solution Try to use IP address instead of host name. If you can use IP address to communicate with a remote server, but can’t use host name, please check DNS setting. a. ‘Broadcast ESSID’ set to off? I can’t locate my AP by my...

  • Page 75: Appendix C: Glossary

    User Manual of WNAP-W2200UE Appendix C: Glossary wireless networking 802.11 under the - 802.11ac is a standard in the family (which is marketed  802.11ac brand name Wi-Fi), developed in the IEEE Standards Association process, providing high-throughput wireless local area networks...
  • Page 76 User Manual of WNAP-W2200UE NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network  to a different IP address for the Internet. PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote hosts to ...
  • Page 77 APΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ essenciais e outras disposições da Directiva ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ 2014/53/EU. ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 2014/53/ΕΚ Por medio de la presente, PLANET Technology Español Slovensky Corporation, declara que 11n Wireless AP Výrobca PLANET Technology Corporation, týmto cumple con los requisitos esenciales y deklaruje, že táto 11n Wireless AP je v súlade so...

Table of Contents