Related Manuals for Datavideo RMC-230
Summary of Contents for Datavideo RMC-230
- Page 1 IRIS/SHUT TER CONTROL BOX RMC-230 Instruction Manual w w w . d a t a v i d e o . c o m...
-
Page 2: Table Of Contents
Datavideo Technologies will try to give correct, complete and suitable information. However, Datavideo Technologies cannot exclude that some information in this manual, from time to time, may not be correct or may be incomplete. This manual may contain typing errors, omissions or incorrect information. -
Page 3: Fcc Compliance Statement
AC adapter. If you are not sure of the type of power available, consult your Datavideo dealer or your local power company. Do not allow anything to rest on the power cord. Do not locate this unit where the power cord will be walked on, rolled over, or otherwise stressed. -
Page 4: Warranty
Warranty Standard Warranty Datavideo equipment are guaranteed against any manufacturing defects for one year from the date of purchase. The original purchase invoice or other documentary evidence should be supplied at the time of any request for repair under warranty. -
Page 5: Three Year Warranty
PCIe Card are covered for 1 year. The three-year warranty must be registered on Datavideo's official website or with your local Datavideo office or one of its authorized distributors within 30 days of purchase. Disposal For EU Customers only - WEEE Marking This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. -
Page 6: Product Overview
Product Overview The main design purpose of the RMC-230 is to replace camera iris and shutter control on MCU-100S and MCU-200S which are cost effective remote controllers designed specifically for remote control of SONY video cameras and camcorders. The RMC-230 acts as an interface connected between an MCU unit and the cameras. -
Page 7: Features
Features Two RJ-45 ports allow the RMC-230 to interface between AD-1S and MCU- 100S. Two PWR ports with one providing power connection and another one allowing cascade of multiple RMC-230 units. Shutter adjustment Iris adjustment ... -
Page 8: System Diagram
System Diagram... -
Page 9: Control Panel
Control Panel T-Bar The T-Bar allows manual adjustment of the iris value; move up to increase and move down to decrease. High iris transition speed button Press to activate high iris transition speed Medium iris transition speed button Press to activate medium iris transition speed... - Page 10 Slow iris transition speed button Press to activate slow iris transition speed 7-Segment Display Screen Displays Iris and Shutter values LEDs IRIS ON: Manual mode IRIS OFF: Auto mode ON: SONY camera shutter ON OFF: SONY camera shutter OFF SHTR ON: Shutter speed display SHTR OFF: IRIS value display Deg ON: Shutter angle is displayed Deg OFF: Shutter speed is displayed...
-
Page 11: Rear Panel
USB Port Connect to the PC for F/W Upgrade PWR Cascade Powers another RMC-230 to cascade multiple RMC-230s DC-IN 12V Connects the supplied 12V PSU to this socket. The connection can be secured by screwing the outer fastening ring of the DC In plug to the socket. -
Page 12: Power Cascade Multiple Rmc-230 Units
To power cascade multiple RMC-230 units, the DC power adapter must be connected to the first RMC-230 unit (DC IN 12V Socket). If the user has to connect the second or the third unit, the user can use the DC power cable to cascade the second unit by connecting another power socket (PWR Cascade) to the DC IN 12V socket of the second unit. -
Page 13: Firmware Upgrade
Press and Hold the shutter button Turn on the RMC-230. 7-segment display of the RMC-230 should display “L-0.5”, and the PC should be able to detect the RMC-230 and recognize it as a USB device. Open the “RMC-230_U1” disk drive on the PC. -
Page 14: Dimensions
Dimensions All measurements in millimetres (mm) -
Page 15: Frequently-Asked Questions
Frequently-Asked Questions This section describes problems that you may encounter while using the RMC-230. If you have questions, please refer to related sections and follow all the suggested solutions. If problem still exists, please contact your distributor or the service center. -
Page 16: Specifications
Specifications Input/Output Connection RJ-45 x 2 Power Jack DC IN x 1 Power Cascade x 1 F/W Upgrade USB x 1 Display 7-segment Display and LED Power DC 12V Environmental Conditions Operating temperature: 0 – 40°C Storage temperature: -10 – 60°C Dimensions 150 x 90 x 97.6mm Weight... -
Page 17: Service & Support
Jun-21.2019 Ver.: E3...