Related Manuals for Sony RM-U401
Summary of Contents for Sony RM-U401
- Page 1 3-864-028-11(1) Remote Commander Operating Instructions RM-U401 1998 by Sony Corporation...
-
Page 2: About This Manual
If you have any question or problem concerning your receiver, please consult your nearest Sony dealer. About This Manual The instructions in this manual are for model RM-U401. Check your model number by looking at the lower right corner of the front side. -
Page 3: Table Of Contents
Before You Use Your Remote Check that you received the following item with the remote: R6 (size-AA) batteries (2) Inserting batteries into the remote Insert two R6 (size-AA) batteries with the + and – properly oriented in the battery compartment. When using the remote, point it at the remote sensor g on the receiver. -
Page 4: Location Of Parts And Basic Remote Operations
Location of Parts and Basic Remote Operations This chapter provides information on the location of buttons and how to use them to perform basic operations. Parts Description SYSTEM STANDBY 1 / u SLEEP SHIFT ENTER > 10 - / - - D.TUNING DISC D.SKIP... - Page 5 5.1 IN to the 5.1/DVD INPUT jacks on the receiver Sony VCRs become operable when you press the VIDEO1, 2, or 3 button. These buttons correspond to VHS, Beta, and 8mm, respectively. See the table on page 10 for information on the buttons you can use to control each component.
- Page 6 Parts Description MENU MENU EXECUTE ENTER CURSOR MENU MODE GUIDE EXIT/RETURN TITLE !£ EFFECT/ EQ/TONE TEST TV/VIDEO DELAY ON/OFF TONE LEVEL P IN P SWAP REAR CENTER POSITION JUMP – – Lift up the top cover. SYSTEM STANDBY 1 / u SLEEP SHIFT ENTER...
- Page 7 !¢ ENTER D.TUNING button If you have selected tuner: Press to enter direct tuning mode. If you have selected VCR, DVD player, LD player, TV, DBS tuner, tape deck, MD deck, or CD player: After selecting a channel, disc, or track using the numeric buttons, press to enter the value.
- Page 8 MUTING – – @º TV CONTROL button If you are using a Sony TV, you can use this remote to operate the TV without turning on the receiver. When you press this button, the TV turns on and switches to TV input.
- Page 9 @¢ DVD MENU button Press to display the DVD menu. Then use the cursor buttons on the remote to perform the menu operations (see “@• Cursor buttons (V/v/B/b), ENTER button, and EXIT/RETURN button” on this page). @∞ DVD TITLE button Press to display the DVD title menu.
- Page 10 + 9 * CD player with a multi-disc changer only. If you press the TV CONTROL button The remote is set to operate only Sony TVs. In this case, only the following buttons are operable: • TV/VIDEO button • CH/PRESET +/– buttons •...
-
Page 11: Advanced Remote Operations
Advanced Remote Operations This chapter describes how to change the factory setting of a function button. SYSTEM STANDBY 1 / u SLEEP SHIFT ENTER > 10 - / - - D.TUNING SHIFT >10 -/- - DISC D.SKIP TV/VTR VIDEO1 VIDEO2 VIDEO3 TAPE TV CONTROL... -
Page 12: Changing The Factory Setting Of A Function Button
You can change the factory settings of the function buttons (page 5) to suit the components in your system. For example, if you connect a Sony LD player to the VIDEO 2 jacks on the receiver, you can set the VIDEO2 button on this remote to control the LD player. -
Page 13: Additional Information
If you experience any of the following difficulties while using the receiver, use this troubleshooting guide to help you remedy the problem. Should any problem persist, consult your nearest Sony dealer. The remote does not function. / Point the remote at the remote sensor g on the receiver. -
Page 14: Specifications
Specifications General Remote contr ol system Infrared control Power r equir ements 3 V DC with two R6 (size-AA) batteries Dimensions 210 56 268 mm (8 inches) Mass (appr ox.) 125 g (4.4 oz) excluding batteries Design and specifications are subject to change without notice. - Page 16 Sony Corporation Printed in Malaysia...