Table of Contents
Advertisement
TOOL STICKERS & TAGS
28502
Name Tag
Dielectric Certifi cation Decal
KEEP KNIFE SHARP.
A DULL KNIFE WILL GIVE A POOR
QUALITY CUT OR MAY CAUSE THE
KNIFE TO BREAK.
25910
Notice Decal
CLOSED
CENTER
FOR USE ON
CLOSED-CENTER
HYDRAULIC SYSTEM
03693
Closed Center Decal
The safety tag (p/n
15875) at right is attached
to the tool when shipped
from the factory. Read
and understand the safety
instructions listed on this
tag before removal. We
suggest you retain this tag
and attach it to the tool
when not in use.
Stanley Hydraulic Tools
3810 SE Naef Road
Milwaukie, Oregon 97267 U.S.A.
Model No.
PR41
NOTICE
D A N G E R
1. FAILURE TO USE HYDRAULIC HOSE LABELED
AND CERTIFIED AS NON-CONDUCTIVE WHEN
USING HYDRAULIC TOOLS ON OR NEAR
ELECTRICAL LINES MAY RESULT IN DEATH
OR SERIOUS INJURY.
BEFORE USING HOSE LABELED AND CERTI-
FIED AS NON-CONDUCTIVE ON OR NEAR
ELECTRIC LINES BE SURE THE HOSE IS
MAINTAINED AS NON-CONDUCTIVE. THE
HOSE SHOULD BE REGULARLY TESTED FOR
ELECTRIC CURRENT LEAKAGE IN ACCOR-
DANCE WITH YOUR SAFETY DEPARTMENT
INSTRUCTIONS.
2.
A HYDRAULIC LEAK OR BURST MAY CAUSE
OIL INJECTION
BODY OR CAUSE OTHER SEVERE PERSONAL
INJURY.
A DO NOT EXCEED SPECIFIED FLOW AND
PRESSURE FOR
I M P O R T A N T
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
SAFETY TAG P/N 15875
7
DANGER
Failure to use hydraulic hose labeled and certified
Failure to use hydraulic hose labeled and certified
as non-conductive when using hydraulic tools on
as non-conductive when using hydraulic tools on
or near electric lines may result in death or
or near electric lines may result in death or
serious injury.
serious injury.
For proper and safe operation read owners manual
For proper and safe operation read owners manual
and mwke sure that you have been properly
and mwke sure that you have been properly
trained in correct procedures required for work
trained in correct procedures required for work
ELECTROCUTION
on or around electric lines.
on or around electric lines.
HAZARD
12412
Electrical Warning Decal
3-9 GPM / 11-34 LPM
DO NOT EXCEED 2000 PSI / 140 BAR
DO NOT EXCEED SPECIFIED FLOW OR PRESSURE
USE CLOSED-CENTER TOOL ON CLOSED-CENTER
SYSTEM. USE OPEN-CENTER TOOL ON OPEN-CENTER
SYSTEM. CORRECTLY CONNECT HOSES TO TOOL "IN"
AND "OUT" PORTS. IMPROPER HANDLING, USE OR OTHER
MAINTENANCE OF TOOL COULD RESULT IN A LEAK, BURST
OR OTHER TOOL FAILURE. CONTACT AT A LEAK OR BURST
CAN CAUSE OIL INJECTION INTO THE BODY. FAILURE TO
OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS
PERSONAL INJURY.
03783
3-9 GPM Decal
D A N G E R
D DO NOT LIFT OR CARRY TOOL BY THE
HOSES. DO NOT ABUSE HOSE. DO NOT
USE KINKED, TORN OR DAMAGED HOSE.
3. MAKE SURE HYDRAULIC HOSES ARE PROP-
ERLY CONNECTED TO THE TOOL BEFORE
PRESSURING SYSTEM. SYSTEM PRESSURE
HOSE MUST ALWAYS BE CONNECTED TO TOOL
"IN" PORT. SYSTEM RETURN HOSE MUST
ALWAYS BE CONNECTED TO TOOL "OUT" PORT.
REVERSING CONNECTIONS MAY CAUSE RE-
VERSE TOOL OPERATION WHICH CAN RESULT
IN SEVERE PERSONAL INJURY.
4. DO NOT CONNECT OPEN-CENTER TOOLS TO
CLOSED-CENTER HYDRAULIC SYSTEMS. THIS
I N T O
T H E
MAY RESULT IN LOSS OF OTHER HYDRAULIC
FUNCTIONS POWERED BY THE SAME SYSTEM
AND/OR SEVERE PERSONAL INJURY.
5. BYSTANDERS MAY BE INJURED IN YOUR WORK
AREA. KEEP BYSTANDERS CLEAR OF YOUR
WORK AREA.
I M P O R T A N T
READ OPERATION MANUAL AND
SAFETY INSTRUCTIONS FOR THIS
TOOL BEFORE USING IT.
USE ONLY PARTS AND REPAIR
PROCEDURES APPROVED BY
STANLEY AND DESCRIBED IN THE
OPERATION MANUAL.
TAG TO BE REMOVED ONLY BY
TOOL OPERATOR.
(shown smaller then actual size)
Advertisement
Table of Contents
