How To Assemble And Operate The Vacuum - Simplicity S20PET Owner's Manual

HOW TO ASSEMBLE AND OPERATE THE VACUUM

How to Attach the Handle to the Vacuum
The vacuum and the handle are packed separately.
1. Slide the handle into the slots on top of the vacuum until it
clicks into place (Fig. 1).
2. Turn the upper cord storage hook to the upright position
and wind the power cord around the cord storage hooks
when storing the vacuum.
How to Release the Power Cord
1. The upper cord hook has a quick-release. To release the
cord, rotate the hook downward (Fig. 2).
2. Return the cord hook to the upright position before
rewinding the cord.
On/Off Switch
1. To turn the vacuum on, push the power pedal on the side of
the vacuum nozzle (Fig. 3).
2. To turn the vacuum off, push the pedal again.
Hand Held Turbo Brush
Attach the brush to the storage holder on the vacuum (Fig. 4).
HOW TO EMPTY THE DUST CONTAINER
Always operate the vacuum with the dust container installed.
Empty the dust container as needed or when it fills to the MAX line.
How to Empty the Dust Container
1. Unplug the vacuum. Press the dust container release button to
remove it from the vacuum (Fig. 5).
2. Press the dust container empty button to open the lid of the
container, releasing the contents into a trash bin (Fig. 6).
3. Close the dust container lid until it clicks and replace the container
into the vacuum.
How to Adjust the
Nozzle Height
Rotate the height adjustment
dial to the type of floor being
vacuumed (Fig. 7).
VC73420MUK Rev1_Instruction Book 30/04/2012 12:17 Page 4
Using in upright mode / Assembly
Attach the tube/handle (1) to the main body of
the cleaner.
Rotate the floor brush height adustment dial
Switch on the vacuum cleaner by pressing the
power pedal (26).
VC73420MUK Rev1_Instruction Book 30/04/2012 12:17 Page 4
4
Using in upright mode / Assembly
Attach the tube/handle (1) to the main body of
the cleaner.
HOW TO ADJUST THE HEIGHT
Rotate the floor brush height adustment dial
VC73420MUK Rev1_Instruction Book 30/04/2012 12:17 Page 4
Using in upright mode / Assembly
Using in upright mode / Assembly
VC73420MUK Rev1_Instruction Book 30/04/2012 12:17 Page
Attach the tube/handle (1) to the main body of
the cleaner.
Using in upright mode / Assembly
Attach the tube/handle (1) to the main body of
the cleaner.
1
Rotate the floor brush height adustment dial
Turn the rotatable cord storage cleat
release the power cord (17). Plug in to the mains
outlet. To keep the cord away from the floor
brush, locate in the cord hook
Attach the tube/handle (1) to the main body of
Rotate the floor brush height adustment dial
the cleaner.
3
floor brush height adjustment dial (10)
Tools
Switch on the vacuum cleaner by pressing the
power pedal (26).
(10) to suit the floor being vacuumed (refer to table above).
Switch on the vacuum cleaner by pressing the
power pedal (26).
4
Rotate the floor brush height adustment dial
Release from the upright position by pressing the
4
upright release pedal (18) with your foot.
IMPORTANT: To prevent damage to carpets,
never leave the cleaner switched on in one
4
place for an extended period.
6
When full, or after use, empty the dust canister
Press the dust canister release button
the dust canister from the vacuum cleaner.
Press the dust canister empty button
Switch on the vacuum cleaner by pressing the
the base of the dust canister, releasing the contents
power pedal (26).
into a bin or a bag. Allergy sufferers may wish to
seal the bag around the dust canister before
emptying to p revent dust escaping.
4
1
4
Turn the rotatable cord storage cleat
release the power cord (17). Plug in to the mains
outlet. To keep the cord away from the floor
brush, locate in the cord hook
3
floor brush height adjustment dial (10)
Tools Deep
pile
carpet
Fig. 7
(10) to suit the floor being vacuumed (refer to table above).
4
Using in upright mode /
Fig. 1
Attach the tube/handle (1) to the m
the cleaner.
1
Fig. 2
(20) to
(3).
Settings for the
Rotate the floor brush height adustm
3
Deep Deep to Medium Smooth
pile medium pile carpet
Fig. 3
carpet pile carpet and
carpet hard
floors
(10) to suit th
Fig. 4
Switch on the vacuum cleaner by pre
power pedal (26).
4
(8).
(4) to remove
(27) to open
Fig. 5
6
2
Fig. 6
(20) to
(3).
Settings for the
Deep to Medium Smooth
medium pile carpet
pile carpet and
carpet hard
floors
5
1
1
Turn
relea
outl
brus
Turn
3 relea
2
outle
fl
brus
3
To
flo
To
(10) to suit the
4
Tur
(10) to suit the
rele
4 out
bru
f
Rele
upri
IMP
neve
T
Rele
plac
6 uprig
5
IMP
When fu
neve
Press the
plac
the dust
6
Press the
When ful
the base
Press the
into a bin
the dust
seal the b
emptyin
Press the
the base
into a bin
seal the b
emptying
Rel
upr
IMP
nev
pla
When fu
Press th
the dus
Press th
the bas
into a b
seal the
emptyin
5