Advertisement
Quick Links
Ice-O-Matic Upright Ice Storage Bins with Ice Shield
Ice-O-Matic ice storage bins enjoy a well-deserved reputation for excellent performance, long-term reliability and
outstanding after-the-sale support. To ensure that this bin delivers that same degree of service, we ask that you
take a moment to review this instruction before beginning the installation of the bin. Should you have any
questions or require technical help at any point, please call our technical service group at (800)423-3367
(US & Canada)
Before You Begin.
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If
damage is found, notify the shipper immediately and contact Ice-O-Matic so that we can help in the filing of a
claim, if necessary.
!
Important Cautions
•
Avoid excessive tightening force when connecting to the bin drain fitting
•
Do not apply excessive heat if any sweating of fittings is necessary. Heat conduction through metal may melt
threads in plastic drain fitting.
• When leveling, do not extend any leg more than 1 in. (26mm) for total leg height no greater than
2.125 in. (54mm).
Installation
1. Remove all packing material from bin.
2. Remove all tape and temporary fastenings from door assemblies and outside of bin.
3. Remove set of four legs and any other accessories packed inside bin.
4. Lay bin on back, being careful to protect finish, and remove bolts holding skid to bin.
5. Screw legs into tapped holes in bin bottom and tighten to seat legs well against bottom.
6. Set bin upright.
7. Remove protective paper from stainless steel exterior.
8. Move bin to permanent location.
9. Adjust "foot" at bottom of each leg to level bin in both directions.
10. Mount icemaker(s) on bin in accordance with icemaker manufacturer's instructions.
11. Connect drain line to 1" FPT female fitting located in bottom of bin.
12. Make final connections to icemaker. (Reference the Ice-O-Matic Installation Manual)
Bin Model Numbers
B700-30, B1000-48, B1300-48, B1325-60, B1600-60
Installation Instructions and Parts List
11100 East 45th Ave.
Denver CO 80239
800 423-3367
www.iceomatic.com
1
1
EP 2138774
9081461-01
01078856R00
12/14
Advertisement
Related Manuals for Ice-O-Matic B700-30
Summary of Contents for Ice-O-Matic B700-30
- Page 1 Before You Begin. After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage is found, notify the shipper immediately and contact Ice-O-Matic so that we can help in the filing of a claim, if necessary.
-
Page 2: Operation
Operation Ice Shield Operation Ice-O-Matic’s unique Ice Shield positively controls the flow of ice into lower door assembly area for removal with either a scoop or shovel. Ice Shield can also be adjusted and locked at one of several levels to accommodate flow characteristics of different types of ice. - Page 3 Interior of bin must be cleaned and sanitized prior to use and should be cleaned on routine basis during use. Interior Bin Care Ice-O-Matic single door upright ice storage bins are equipped with polyethylene liner walls and stainless steel bottoms which should be cleaned and sanitized periodically with any product suitable for use in a food zone.
-
Page 4: Replacement Parts
Replacement Parts Item Ice-O-Matic DESCRIPTION B700 B1000 B1300 B1325 B1600 Part Number 48 48 60 60 No Item Number 1 NA NA NA NA 1011518-10 Inspection Window 21.125 x 8.625 2 Required 1011517-10 Inspection Window 21.125 x 8.625 2 Required... - Page 5 GASKET PATTERN FOR ICE-O-MATIC FLEXITOP 30" WIDE BIN ICE 1006 ICE 1506 7/16 23 11/16 SEAL INSIDE EDGE SEAL INSIDE EDGE 25 5/8 WITH SEALANT WITH SEALANT front front GASKET GASKET NO FILLER PANEL REQ'D NO FILLER PANEL REQ'D ICE 0926...
- Page 6 GASKET PATTERN FOR ICE-O-MATIC FLEXITOP 48" WIDE BIN ICE 1406, ICE 1806, ICE 2106 MFI 2406 3/16 5/16 6 3/8 7/16 23 11/16 24 3/16 SEAL INSIDE EDGE SEAL INSIDE EDGE WITH SEALANT WITH SEALANT front front GASKET 8 7/8...
- Page 7 ICE 1506 ICE 1006 SEAL INSIDE EDGE 7/16 WITH SEALANT 9 3/8 12 3/8 7 1/8 OPENING OPENING 25 5/8 23 11/16 SEAL INSIDE EDGE FILLER 'L' WITH SEALANT GASKET front front GASKET 13 3/8 9 3/4 13 1/2 9 7/8 FILLER 'S' FILLER 'S' FILLER 'L'...
- Page 8 GASKET PATTERN FOR ICE-O-MATIC FLEXITOP 60" WIDE BIN ICE 1406, ICE 1806, ICE 2106 MFI 2406 3/16 6 11/16 5 7/16 13 1/8 7/16 FILLER 'L' 23 11/16 24 3/16 SEAL INSIDE EDGE SEAL INSIDE EDGE WITH SEALANT WITH SEALANT...
- Page 9 ICE 1506 ICE 1006 7/16 15 1/16 15 1/16 15 1/16 15 1/16 FILLER 'L' FILLER 'L' FILLER 'L' FILLER 'L' 25 5/8 23 11/16 SEAL INSIDE EDGE SEAL INSIDE EDGE WITH SEALANT WITH SEALANT front front GASKET GASKET 16 1/16 16 1/16 16 1/16 16 1/16...
- Page 12 9081461-01 01078856R00 12/14...