Advertisement
Quick Links
This Document is meant to educate how a Spektrum DX9 owner can upgrade their transmitter to
provide a serial data port for use with the Team Black Sheep Crossfire Module.
Currently there are 2 methods.
Please read this disclaimer before using a Spektrum DX9 with the TBS Crossfire Module.
Using the Crossfire firmware
By downloading this firmware, you acknowledge that you understand the use and liability of
long range radio systems, such as the Team Black Sheep Crossfire long range system, and that flying
beyond line of sight can be hazardous and potentially illegal. Horizon Hobby in no way endorses
hazardous and/or illegal activities, and it is the user's responsibility to understand and follow all local
laws and regulations. Furthermore, Horizon is not responsible for any loss of control that may result in
damages or loss of property when using external RF modules with Spektrum Equipment.
Modification for use of the Team Black Sheep Crossfire System
The TBS Crossfire long range system is intended to provide less latency and greater range than
standard systems in the DX9 radio. However, installing the Crossfire system requires soldering a new
serial port onto the transmitter circuit board. We have provided a comprehensive tutorial to perform
this modification on a Spektrum DX9 Transmitter correctly. Please be aware that any self-modification of
the transmitter will void your transmitter warranty. Future service on a self-modified transmitter will not
be denied, but any future service performed will not be covered under warranty, and repairs will be
billed accordingly. As a result, Horizon strongly recommends sending your Spektrum radio in for service
and allowing our professional service technicians to perform the Crossfire system installation and
preserve your warranty. Click
service request asking for this modification.
Once we receive your Transmitter, an authorized Spektrum Service Technician will perform the
modification and confirm that the Transmitter functions properly post upgrade. Once the modification is
completed, your radio will have a common servo connector leading out the back of the radio that offers
serial port signal and ground. Use this plug to connect and communicate with your serial input module.
The cost for this modification is $75 plus shipping and is currently only offered for the Spektrum DX9 and
DX9 Black Edition transmitters.
* PLEASE NOTE THAT THIS SERVICE IS CURRENTLY AVAILABLE ONLY FOR US AND CANADA
*** PLEASE NOTE THAT HORIZON HOBBY DOES NOT SUPPORT OR WARRANTY TEAM BLACKSHEEP
PRODUCTS. IF YOU HAVE QUESTIONS OR NEED SERVICE WITH A TBS CROSSFIRE OR OTHER TBS
PRODUCTS, PLEASE CONTACT TEAM BLACKSHEEP DIRECTLY.
- - DX9 Crossfire Disclaimer - -
here
to start the service request process. Please include a note in the
©2017 Horizon Hobby, LLC. All Rights Reserved.
4105 Fieldstone Rd • Champaign, IL • 61822 • 800.535.5551 • fastserve.horizonhobby.com
Advertisement
Related Manuals for Spektrum DX9
Summary of Contents for Spektrum DX9
- Page 1 Use this plug to connect and communicate with your serial input module. The cost for this modification is $75 plus shipping and is currently only offered for the Spektrum DX9 and DX9 Black Edition transmitters.
- Page 2 Method 1 – Self Modification – How to install a serial port on your Spektrum DX9 These instructions are geared toward the Do it Yourself enthusiast, if you do not possess the knowledge and confidence to perform a minor modification to your RC equipment, or if your radio is still with in the 1 year warranty period, please continue to Method 2.
- Page 3 Find the pin holes labeled . We are using the 2 and 3 holes down for TX and Ground respectively. Proceed to “tin” these two locations and solder the signal and ground leads to them, being careful not to bridge the gap. For extra precaution, use a multi-meter to check that you have no continuity between these points once soldering is complete.
- Page 4 Step 5) Create a interface cable The DX9 will be interfacing this serial port with the EXP Port on the TBS Crossfire. This is the 6 Pin port. Here is a diagram for the cable and an example.
- Page 5 Once logged in, find your registered DX9 (if you have not done so, do so now) and then find Update Firmware. Browse through until you locate the latest firmware that incorporates Crossfire/Serial data port.
- Page 6 The cost for this modification is $75 plus shipping and is currently only offered for the Spektrum DX9 and DX9 Black Edition transmitters. With this service your DX9 will have a male servo lead out of the back of the transmitter and we will include an adapter used for the EXP port on a TBS Crossfire to this lead.