Advertisement
Ignitor Lighting
READ INSTRUCTIONS BEFORE LIGHTING.
Do NOT lean over barbecue while lighting.
1. Turn gas burner control valve to
2. Turn ON gas at LPG gas cylinder.
3. Open the barbecue lid.
4. Press and turn the control knob to the
5. Push and hold ELECTRONIC IGNITOR button until
the burner lights.
6. Once the burner has ignited, turn the control knob to
the desired setting.
7. If ignition does not occur in 5 seconds, turn the burner
control knob to
, wait 5 minutes, and repeat lighting
procedure.
If ignition still does not occur, follow match-
lighting instructions.
WARNING
Turn control knob and LPG cylinder OFF when not in
use.
CAUTION
If ignition does NOT occur in 5 seconds, turn the
control knob to
, wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with
the valve open, gas will continue to flow out of the
burner and could accidently ignite with risk of injury.
Match-Lighting
Do NOT lean over barbecue while lighting.
1.Turn gas burner control valve to
2.Turn ON gas at LPG cylinder.
3. Open barbecue lid.
4. Insert match into match holder. Strike match. Place lit
match into match light hole at the rear of the barbecue
bottom, shown "A". Make sure lit match is placed inside
through the hole and near burner.
5.Push in and turn control knob to position 5 . Be sure
burner lights and stays lit.
A
Rotate Match
Light Hole
Cover
.
position.
.
Match Light Hole
View is from
rear of
appliance
Burner Flame Check
• Light burner. Looking through the match light hole underneath
the barbecue, you should see the flame height as shown
below. Turn control knob from position 5 to 1 . The Flame
height should decrease. Always check flame prior to each use.
If only low flame is seen refer to "Sudden drop or low flame" in
the Troubleshooting Section.
Turning Barbecue Off
• Turn control knob to
OFF
by turning hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Press and hold electronic
ignitor button. "Click" should be heard and spark seen each
time in each collector box or between burner and electrode.
See "Troubleshooting" if no click or spark.
Valve Check
• Important: Make sure gas is off at LPG cylinder
before checking valve. Knob locks in
check valve, first push in knob and release, knob should
spring back. If knob does not spring back, replace valve
assembly before using this barbecue. Turn knob to
position 1 then turn back to
turn smoothly.
Hose Check
• Before each use, check to see if hose is cut, worn or
kinked. Replace damaged hose before using applaince.
Use only valve/hose/regulator specified by
manufacturer.
Normal
Hose
General Barbecue Cleaning
• Meat Thermometer: Do not immerse or soak in water.
Wash with warm soapy water and wipe dry.
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors are not painted at the factory
(and should never be painted). Apply a strong solution
of detergent and water or use a barbecue cleaner with scrub
brush on insides of barbecue lid and bottom. Rinse and
allow to completely air dry. Do not apply a caustic
barbecue/oven cleaner to painted surfaces. A black surface
improves the appliances performance.
• Plastic parts: Wash with warm soapy water and wipe dry.
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated barbecue cleaner on plastic parts. Damage to and
failure of parts can result.
• Painted surfaces: Wash with mild detergent or non-
abrasive cleaner and warm soapy water. Wipe dry with a
soft non-abrasive cloth.
•
Cooking surfaces: If a bristle brush is used to clean any
of the barbecue cooking surfaces, ensure no loose bristles remain
on cooking surfaces prior to barbecuing. It is not recommended
to clean cooking surfaces while barbecue is hot.
8
High Flame
Low Flame
position. Turn LPG cy linder
OFF
position. To
position. Valve should
Kinked
Hose
OFF
Advertisement
Troubleshooting
