Table of Contents
Advertisement
ThermoFresh
Systems
®
1.0 & 1.5 Gallon Servers
with Digital Sight Gauge or
Mechanical Sight Gauge
USE & CARE INFORMATION
CAUTION: CLEAN AND SANITIZE YOUR SERVER BEFORE USING. SEE NOTE #1 of DAILY CLEANING.
BUNN-O-MATIC CORPORATION
POST OFFICE BOX 3227
SPRINGFIELD, ILLINOIS 62708-3227
PHONE: (217) 529-6601 FAX: (217) 529-6644
www.bunn.com
54923.0000C 02/19 ©2018 Bunn-O-Matic Corporation
Advertisement
Table of Contents
Related Manuals for Bunn ThermoFresh Series
Summary of Contents for Bunn ThermoFresh Series
- Page 1 Mechanical Sight Gauge USE & CARE INFORMATION CAUTION: CLEAN AND SANITIZE YOUR SERVER BEFORE USING. SEE NOTE #1 of DAILY CLEANING. BUNN-O-MATIC CORPORATION POST OFFICE BOX 3227 SPRINGFIELD, ILLINOIS 62708-3227 PHONE: (217) 529-6601 FAX: (217) 529-6644 www.bunn.com 54923.0000C 02/19 ©2018 Bunn-O-Matic Corporation...
- Page 2 AS SPECIFIED HEREIN, TO REPAIR, REPLACEMENT OR REFUND. In no event shall BUNN be liable for any other damage or loss, including, but not limited to, lost profits, lost sales, loss of use of equipment, claims of Buyer’s customers, cost of capital, cost of down time, cost of substitute equipment, facilities or services, or any other special, incidental or consequential damages.
-
Page 3: North American Requirements
CE REQUIREMENTS • This appliance must be installed in locations where it can be overseen by trained personnel. • For proper operation, this appliance must be installed where the temperature is between 5°C to 35°C. • Appliance shall not be tilted more than 10° for safe operation. •... -
Page 4: User Notices
INTRODUCTION This server is intended for use with a BUNN DUAL TF DBC , SINGLE TF DBC or ICB family brewers. ® ® ® ® ® When proper precautions are followed, 1.0 up to 1.5 gallons of coffee may be brewed directly into the server and then transported to a remote serving location. -
Page 5: Daily Cleaning
CAUTION: CLEAN AND SANITIZE YOUR SERVER DAILY NOTE: Bunn-O-Matic recommends the three step method for cleaning and sanitizing the server. The 3 step method consists of hot soapy water using an mild, non-citrus detergent, a fresh water rinse and an aqueous sanitizing solution using a non-chlorine sanitizer. -
Page 6: Replacement Parts
SERVERS WITH STAND - Mechanical Sight Gauge REPLACEMENT PARTS 1. 53905.0000 2. 54489.0001 Lid, 1.0 gal 54489.0000 Lid, 1.5 gal 3. 54938.0000 Decal, Do Not Submerge/Do Not Spray 4. 54086.1000 Top Cover with Handle and decal 42761.0000 Screw, Pan Head M4 x 9 5. - Page 7 SERVERS WITH STAND - Digital Sight Gauge REPLACEMENT PARTS 53905.0000 53912.1000 DSG Lid Assy, 1.0 gal (Includes Cap) 53912.1001 DSG Lid Assy, 1.5 gal (Includes Cap) 39043.0003 Decal, Do Not Submerge Server 54938.0000 Decal, Do Not Submerge/Do Not Spray 54086.1000 Top Cover with Handle and decal 54470.0000 Plug...
-
Page 8: Digital Display
DIGITAL DISPLAY The Digital Sight Gauge (DSG) senses liquid levels and monitors hold times. Horizontal bars indicate the liquid level. The 1.0 gallon sensor displays a total of 4 bars and the 1.5 gallon sensor displays 6 bars. Each bar represents approximately 32 ounces of liquid. All bars will be displayed when the server is full. -
Page 9: Low Battery Indication
PROGRAMMING A 10 position rotary switch is used to view and change the configuration parameters. The rotary switch is accessible when the battery cover and holder are removed. Position 0 Run – This is the normal rotary switch setting and allows the DSG to run with the given configuration. The rotary switch must be in this position for normal operation. -
Page 10: Battery Replacement
BATTERY REPLACEMENT The Digital Sight Gauge lid comes equipped with 4 AAA batteries. The batteries have a use life of approximately 1 years under normal operating conditions. NOTE: Batteries are not covered under product warranty. To replace the batteries: 1. Remove the lid assembly from the server. 2.