Viessmann VITOPEND 222 WHSA Datasheet page 34

Gas fired boiler with an integral primary cylinder for open or balanced flue operation 10.5 to 24 30 kw

Hide thumbs

Table Of Contents

Table of Contents

Flue gas/ventilation air system accessories for balanced flue operation...

A Ventilation air

B Flue gas

A Ventilation air

B Flue gas

Vertical pitched and flat roof outlet, parallel, system size Ø 80/80 mm

For installing the Vitopend in an attic (type C

The roof outlet may only be used, where the ceiling of the occu-

pied room also forms part of the roof or only the roof structure is

located above the ceiling (pitched attic).

When the balanced flue system is routed through roof spaces,

which are not used as accommodation, run the balanced flue

pipe through an additional metal pipe as protection against

mechanical damage (TRGI '86/96, point 5.6.1.2).

VIESMANN

1 Boiler flue connection bend (coaxial)

(order separately)

2 External wall terminal (Ø 60/100 mm)

(incl. wall bezels)

3 Balanced flue pipe (Ø 60/100 mm)

1 m long (trim to size)

0.5 m long (trim to size)

4 Protective grille where the flue term-

inal is near public paths

Balanced flue bend (Ø 60/100 mm)

90°

45° (2 pieces)

Balanced flue inspection piece

straight (Ø 60/100 mm)

Balanced flue condensate trap (Ø

60/100 mm)

Drain outlet kit

1 Boiler flue connection bend (coaxial)

(order separately)

2 External wall terminal (Ø 60/100 mm)

(incl. wall bezels)

3 Balanced flue pipe (Ø 60/100 mm)

1 m long (trim to size)

0.5 m long (trim to size)

Balanced flue bend (Ø 60/100 mm)

90°

45° (2 pieces)

Balanced flue inspection piece

straight (Ø 60/100 mm)

Balanced flue condensate trap (Ø

60/100 mm)

Drain outlet kit

)

It may also be routed behind a jamb wall or a solid wall of an

32x

attic built as accommodation, if the fire protection class of the

jamb wall corresponds to that of the ceiling (e.g. B30).

It was verified as part of the DIN DVGW type test, that nowhere

on Vitopend or the balanced flue system will surface tempera-

tures higher than 40 K above room temperature occur.

Minimum clearances to combustible materials inside the instal-

lation location or in connection with the roof outlet do not have

to be observed.

(cont.)

Part no. 7194 858

Part no. 7194 843

Part no. 7194 841

Part no. 7194 842

Part no. 7337 276

Part no. 7194 836

Part no. 7194 837

Part no. 7194 833

Part no. 7194 846

Part no. 7179 307

Part no. 7194 858

Part no. 7194 843

Part no. 7194 841

Part no. 7194 842

Part no. 7194 836

Part no. 7194 837

Part no. 7194 833

Part no. 7194 846

Part no. 7179 307

VITOPEND 222

Table of Contents

Show Quick Links

Hide quick links:

Table of Contents

This manual is also suitable for:

Vitopend 100 whea Vitopend 200 whka Vitopend 100 wh0a

Viessmann VITOPEND 222 WHSA Datasheet page 34

Hide quick links:

Related Manuals for Viessmann VITOPEND 222 WHSA

Related Products for Viessmann VITOPEND 222 WHSA

This manual is also suitable for:

Table of Contents