Advertisement
Quick Links
1
INSTRUCTIONS FOR SAFE AND PROPER USE _______________________ 4
2
POSITIONING OF THE HOB _______________________________________ 6
3
ELECTRICAL CONNECTION _______________________________________ 8
4
GAS CONNECTION ______________________________________________ 9
5
ADAPTATION TO DIFFERENT TYPES OF GAS_______________________ 11
6
FINAL OPERATIONS ____________________________________________ 14
7
USING THE HOB _______________________________________________ 17
8
CLEANING AND MAINTENANCE __________________________________ 20
INSTRUCTIONS FOR THE INSTALLER: these are for the qualified
technician who must carry out a suitable check of the gas system, install
the appliance, set it functioning and carry out an inspection test.
INSTRUCTIONS FOR THE USER: these contain user advice, description
of the commands and the correct procedures for cleaning and
maintenance of the appliance.
Contents
3
Advertisement
Related Manuals for Smeg SER63LPG3
Summary of Contents for Smeg SER63LPG3
-
Page 1: Table Of Contents
INSTRUCTIONS FOR SAFE AND PROPER USE _______________________ 4 POSITIONING OF THE HOB _______________________________________ 6 ELECTRICAL CONNECTION _______________________________________ 8 GAS CONNECTION ______________________________________________ 9 ADAPTATION TO DIFFERENT TYPES OF GAS_______________________ 11 FINAL OPERATIONS ____________________________________________ 14 USING THE HOB _______________________________________________ 17 CLEANING AND MAINTENANCE __________________________________ 20 INSTRUCTIONS FOR THE INSTALLER: these are for the qualified technician who must carry out a suitable check of the gas system, install the appliance, set it functioning and carry out an inspection test. -
Page 2: Instructions For Safe And Proper Use
Introduction INSTRUCTIONS FOR SAFE AND PROPER USE THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE AND THEREFORE MUST BE KEPT IN ITS ENTIRETY AND IN AN ACCESSIBLE PLACE FOR THE WHOLE WORKING LIFE OF THE COOKING HOB. WE ADVISE READING THIS MANUAL AND ALL THE INSTRUCTIONS THEREIN BEFORE USING THE COOKING HOB. - Page 3 Introduction THE IDENTIFICATION PLATE, WITH TECHNICAL DATA, SERIAL NUMBER AND MARKING IS CLEARLY VISIBLE UNDER THE CASING. THE PLATE ON THE CASING MUST NOT BE REMOVED. BEFORE CONNECTING THE DEVICE, MAKE SURE THAT IT HAS BEEN REGULATED FOR THE TYPE OF GAS THAT WILL FEED IT, CHECKING THE LABEL UNDER THE HOB.
-
Page 4: Positioning Of The Hob
Instructions for the installer POSITIONING OF THE HOB The following operation requires building and/or carpentry work so must be carried out by a competent tradesman. Installation can be carried out on various materials such as masonry, metal, solid wood or plastic laminated wood as long as they are heat resistant (T 90°C). - Page 5 Instructions for the installer Bracket ‘A’ in the 1st slot Bracket ‘A’ in the 2nd slot Bracket ‘B’ Fixing 90 cm hobs on 60 cm base unit If a 90 cm hob is to be bracketed to a 60 cm base unit, 2 central brackets “A”...
-
Page 6: Electrical Connection
Instructions for the installer ELECTRICAL CONNECTION Make sure that the voltage and capacity of the power line conform to the data shown on the plate located under the casing. Do not remove this plate for any reason. The plug on the end of the supply cable and the wall socket must be the same type and conform to the current electrical system regulations. -
Page 7: Gas Connection
Instructions for the installer GAS CONNECTION Connection to the gas mains may be made with a rigid copper pipe or with a flexible pipe and conforming to the provisions defined by standard regulations in force. To facilitate connection, fitting A on the rear of the appliance may be adjusted laterally. - Page 8 Instructions for the installer Connection to LPG Use a pressure regulator and make the connection to the tank according to the provisions of standards regulations in force. Make sure that feed pressure conforms to the levels shown in the table in paragraph “5.3 Regulation for LPG”.
-
Page 9: Adaptation To Different Types Of Gas
Instructions for the installer ADAPTATION TO DIFFERENT TYPES OF GAS Before performing any cleaning or maintenance work, disconnect the appliance from the electrical socket. The hob has been inspected for LPG at a pressure of 30 mbar. Removing the separable control panel (models with separable control panel) Remove the knobs and the knob guard tube “A”... - Page 10 Instructions for the installer Regulation for LPG Check that the connection has been made as described in the “Gas connection” section. Undo the screw “D” and push the air regulator “C” fully down. Use a spanner to remove the nozzles “B” and fit those of suitable type following the instructions given in the tables for bottled gas G30/G31 –...
- Page 11 Instructions for the installer Regulation of primary air Referred to distance “A” in mm. 60 cm hobs with separable control panel. Burner Auxiliary (1) Semirapid r (2) Semirapid l (3) Rapid large (4) Ultrarapid (5) 90 cm hobs with separable control panel. Burner Auxiliary (1) Semirapid (2)
-
Page 12: Final Operations
Instructions for the installer FINAL OPERATIONS Having carried out the above adjustments, reassemble the appliance following, backwards, the instructions in paragraph “5.1 Removing the separable control panel / 5.2 Removing the hob”. Regulation of minimum for natural gas Reposition the components on the burner and slide the knobs onto the cock stems. - Page 13 Instructions for the installer Arrangement of the burners on the hob (Hob with separable control panel) 60 cm. hob BURNERS Auxiliary Semirapid r Semirapid l Rapid large Ultrarapid 90 cm. hob BURNERS Auxiliary Semirapid Rapid Fish burner Ultrarapid...
- Page 14 Instructions for the installer Arrangement of the burners on the hob (Hob with built-in control panel). 60 cm. hob Lubrication of gas taps With time it may happen that the gas taps get blocked and hard to turn. Clean them inside and re-grease them. This operation must be done by an authorised person.
-
Page 15: Using The Hob
Instructions for the user USING THE HOB Before turning on the burners, make sure that the burner rings, caps and grids have been fitted correctly. In the ultrarapid burner, notch A must be aligned with pin B. Grid C provided is intended for use with woks (Chinese pans). Adapter D comes only with open grids models and is intended for use with small sized vessels. - Page 16 Instructions for the user Diameter of the pans Burners Auxiliary Semirapid Rapid medio Rapid large Ultrarapid Fish burner Electric elements 7.4.1 Turning on electric elements Hobs may be fitted with an electric element of varying diameter. The electric element is controlled by a switch and is turned on by rotating the appropriate knob to the desired position.
- Page 17 Instructions for the user WARNING When switching on the electric element for the first time, or if the electric element has not been used for a long time, to remove any humidity from the insulating material it should be dried out by placing the electric element on position 1 for 30 minutes.
-
Page 18: Cleaning And Maintenance
Instructions for the user CLEANING AND MAINTENANCE Before any intervention, disconnect the power supply of the device. Cleaning Clean the cooking top regularly every time you use it, obviously after it has cooled. 8.1.1 Regular daily cleaning of the hob In order to clean and preserve the surface, always use specific products only, which do not contain abrasive substances or chlorine- based acid substances. - Page 19 Instructions for the user 8.2.2 The electric element After use, to make sure that the surfaces are clean and long lasting, the electric element must be treated with specific cleaning products which are available on the market. This necessary operation prevents oxidisation (rust formation).