Table of Contents
Advertisement
21. Red Adjustment (Command2:v)
G To adjust red in color temperature.
Transmission
[k][v][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
•
Refer to 'Real data mapping 2'. See page 27.
Acknowledgement
[v][ ][Set ID][ ][OK][Data][x]
22. Green Adjustment (Command2:w)
G To adjust green in color temperature.
Transmission
[k][w][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
•
Refer to 'Real data mapping 2'. See page 27.
Acknowledgement
[w][ ][Set ID][ ][OK][Data][x]
23. Blue Adjustment (Command2:$)
G To adjust blue in color temperature.
Transmission
[k][$][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
•
Refer to 'Real data mapping 2'. See page 27.
Acknowledgement
[$][ ][Set ID][ ][OK][Data][x]
24. PIP Input Select (Command2:y)
G To select input source for sub picture in PIP mode.
Transmission
[k][y][ ][Set ID][ ][Data][Cr]
Data 0: RGB1
1: COMPONENT
2: VIDEO
3: S-VIDEO
Acknowledgement
[y][ ][Set ID][ ][OK][Data][x]
25. Abnormal State (Command2:z)
G To recognize an abnormal state.
Transmission
[k][z][ ][Set ID][ ][FF][Cr]
Data 0: Normal (Power on and signal exist)
1: No signal (Power on)
2: Turn the monitor off by remote control
3: Turn the monitor off by sleep time function
4: Turn the monitor off by RS-232C function
5: 5V down
6: AC down
7: Turn the monitor off by Fan Alarm function
8: Turn the monitor off by off time function
9: Turn the monitor off by auto off function
a: Turn the monitor off by AV board detect
Acknowledgement
[z][ ][Set ID][ ][OK][Data][x]
* This function is "read only".
26. Orbiter (Command2:p)
G To control the orbiter function on/off.
Transmission
[j][p][ ][Set ID][ ][Data][Cr]
Data 0: Orbiter off
Acknowledgement
[p][ ][Set ID][ ][OK][Data][x]
27. White Wash (Command2:q)
G To control the white wash function on/off.
Transmission
[j][q][ ][Set ID][ ][Data][Cr]
Data 0: White Wash off
Acknowledgement
[q][ ][Set ID][ ][OK][Data][x]
28. Orbiter Time Setting (Command2:r)
G To adjust orbiter operation time term.
Transmission
[j][r][ ][Set ID][ ][Data][Cr]
Data Min: 1 ~ Max: FE
Acknowledgement
[r][ ][Set ID][ ][OK][Data][x]
29. Orbiter Pixel Setting (Command2:s)
4: RGB2
G To adjust pixel number in orbiter function.
Transmission
[j][s][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 9
Acknowledgement
[s][ ][Set ID][ ][OK][Data][x]
30. Picture Size Setting for Twin Picture mode
G To adjust main window size in twin picture mode.
Transmission
[j][t][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
Acknowledgement
[t][ ][Set ID][ ][OK][Data][x]
1: Orbiter on
1: White Wash on
•
Refer to 'Real data mapping1'. See page 27.
•
Refer to 'Real data mapping1'. See page 27.
(Command2:t)
•
Refer to 'Real data mapping1'. See page 27.
External Control Device Setup
Owner's Manual 29
Advertisement
Table of Contents
