Page 1
CANADA : http//biz.lgservice.com : http//www.lgservice.com : http//lgservice.com/techsup.html PLASMA MONITOR SERVICE MANUAL CHASSIS : RF-03GB MODEL : MU-50PZ90V/M/C CAUTION BEFORE SERVICING THE CHASSIS, READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
If the exposed metallic part has a return path to the chassis, the measured resistance should be between 1MΩ and 5.2MΩ. When the exposed metal has no return path to the chassis the CANADA: LG Electronics Canada, Inc. 550 Matheson reading must be infinite. Boulevard East Mississauga, Ontario L4Z 4G3 An other abnormality exists that must be corrected before the receiver is returned to the customer.
TABLE OF CONTENTS DESCRIPTION OF CONTROLS ...........4 SPECIFICATIONS..............6 EXTERNAL CONTROL DEVICE SETUP......8 IR CODE................14 ADJUSTMENT INSTRUCTION...........16 PRINTED CIRCUIT BOARD ..........20 BLOCK DIAGRAM...............25 EXPLODED VIEW...............26 EXPLODED VIEW PARTS LIST .........27 REPLACEMENT PARTS LIST ..........28 SCHEMATIC DIAGRAM............- 3 -...
DESCRIPTION OF CONTROLS Controls Controls Front Panel Controls Front Panel Controls - This is a simplified representation of front panel. Here shown may be somewhat different from your monitor. ON/OFF Buttons Main Power Button INPUT SELECT Button VOLUME ( ) Buttons MENU Button Remote Control Sensor Power Standby Indicator...
DESCRIPTION OF CONTROLS Remote Control Key Functions Remote Control Key Functions - When using the remote control, aim it at the remote control sensor on the monitor. - Under certain conditions such as if the remote IR signal is interrupted, the remote control may not function. Press the key again as necessary.
EXTERNAL CONTROL DEVICE SETUP - Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally. - Connect the serial port of the control device to the RS-232C jack on the Monitor back panel. - RS-232C connection cables are not supplied with the Monitor.
Page 9
EXTERNAL CONTROL DEVICE SETUP Set ID Set ID - Use this function to specify a monitor ID number. - Refer to ‘Real Data Mapping 1’. See page 27. 1. Press the MENU button and then use the button to select the SPECIAL menu. D D / E E VIDEO Language...
Page 10
EXTERNAL CONTROL DEVICE SETUP 04. Screen Mute (Command2:d) 01. Power (Command2:a) G To control Power On/Off of the Monitor. G To select screen mute on/off. Transmission Transmission [k][a][ ][Set ID][ ][Data][Cr] [k][d][ ][Set ID][ ][Data][Cr] Data 0 : Power Off 1 : Power On Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off)
Page 11
EXTERNAL CONTROL DEVICE SETUP 08. Brightness (Command2:h) 13. Remote Control Lock Mode (Command2:m) G To adjust screen brightness. G To lock the remote control and front panel controls on the You can also adjust brightness in the Video menu. monitor Transmission Transmission [k][h][ ][Set ID][ ][Data][Cr]...
Page 12
EXTERNAL CONTROL DEVICE SETUP 17. PIP Position (Command2:q) 21. Color Temperature (Command2:u) G To select sub picture position for PIP. G To adjust color temperature. You can also adjust ACC in the Video menu. You can also adjust the sub picture position using Win.position on the remote control or in the Twin menu.
Page 13
EXTERNAL CONTROL DEVICE SETUP 25. PIP Input Select (Command2:y) 29. Orbiter Time Setting (Command2:r) G To adjust orbiter operation time term. G To select input source for sub picture in PIP mode. Transmission Transmission [k][y][ ][Set ID][ ][Data][Cr] [j][r][ ][Set ID][ ][Data][Cr] Data 0: RGB 1: Component Data Min: 1 ~ Max: FE...
IR CODE How to Connect How to Connect G Connect your wired remote control to the Remote Control port on the Monitor. Remote Control IR Code Remote Control IR Code G Output waveform Single pulse, modulated with 37.917KHz signal at 455KHz Carrier frequency = 1/T Duty ratio = T1/T...
Page 15
IR CODE Code (Hexa) Function Note UP ( R/C Button DOWN ( R/C Button VOL+ ( R/C Button VOL- ( R/C Button POWER On/Off R/C Button (Power On/Off) POWER ON Discrete IR Code (Only Power On) POWER OFF Discrete IR Code (Only Power Off) MUTE R/C Button Number Key 0...
ADJUSTMENT INSTRUCTIONS You can check whether circuit adjustment is operated well or 1. Application Object not, as below. These instructions are applied to all of the PDP monitor, RF- (1) Display RGB1 to the Main picture, CVBS to the Sub 03GB.
ADJUSTMENT INSTRUCTIONS 2) After turning the RV401, voltage of D.M.M adjustment as 6-3. Adjustment of White Balance same as Vs voltage which on label of panel Right/Top. Operate the Zero-calibration of the CA-100, then stick sensor (Deviation : ±0.5V) to PDP module surface when you adjust. For manual adjustment, it is also possible by the following P805 P805...
ADJUSTMENT INSTRUCTIONS * [Cr]: Carriage Return ASCII code ‘0x0D’ Transmission * [ ]: ASCII code ‘space (0x20)’ [j][a][][Set ID][][FF][Cr] Transmission [command2[ [] [Set ID] [] [OK][Data][x] Acknowledge The Set transmits ACK (acknowledgement) based on this [a][][Set ID][][OK][Data][x] Data:0H~64H format when receiving normal data. At this time, if the data Input Select (Command: b)(Input Main Picture) $ Select the is data read mode, it indicates present status data.
Page 19
ADJUSTMENT INSTRUCTIONS (2) DDC Data input for Digital-RGB 1) Connect PC Serial to DVI Cable of JIG for DDC Adjustment to DVI terminal (DVI Jack). 2) Operate S/W for DDC record and select DDC Data for Digital RGB in Model Menu. 3) Operate EDID Write command.
REPLACEMENT PARTS LIST For Capacitor & Resistors, the CC, CX, CK, CN : Ceramic RD : Carbon Film charactors at 2nd and 3rd digit CQ : Polyestor RS : Metal Oxide Film RUN DATE : 2004.4.7 in the P/No. means as follows; CE : Electrolytic RN : Metal Film RF : Fusible...
Page 29
REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION Q413 0TR150400BA CHIP 2SA1504S(ASY) KEC D115 0DD226239AA CHIP KDS226 SOT23 CHIP 2SA1504S(ASY) KEC CHIP KDS226 SOT23 Q414 0TR150400BA D854 0DD226239AA 0TR150400BA CHIP 2SA1504S(ASY) KEC 0DD226239AA CHIP KDS226 SOT23 Q415 D855 Q416...
Page 30
REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION C025 0CE474SK6DC 0.47UF MVG 50V M C1506 0CK224DF56A 220000PF 2012 16V 10% 1UF MVG 50V M 220000PF 2012 16V 10% C026 0CE105SK6DC C1507 0CK224DF56A 0CE106SF6DC 10UF MVG 16V 20% 0CK224DF56A 220000PF 2012 16V 10% C029...
Page 31
REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION C793 0CE227VF6DC 220UF MV 16V 20% AR1460 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% 100UF MVG 16V M 22 OHM 1 / 16 W 1608 5% C812 0CE107SF6DC AR1461...
Page 32
REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION AR552 0RRZVTA001C 4.7K OHM 1 / 16 W 1608 5% L007 6210VC0006A FILTER,EMC FBMH3216 HM501NT 4.7K OHM 1 / 16 W 1608 5% FILTER,EMC FBMH3216 HM501NT AR553 0RRZVTA001C L008 6210VC0006A...
Page 33
REPLACEMENT PARTS LIST LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION L929 6210VC0006A FILTER,EMC FBMH3216 HM501NT LA201 6210VC0006A FILTER,EMC FBMH3216 HM501NT 6200JB8010L FILTER,EMC MLB2012091000LN2 R129 R130 6200JB8010L FILTER,EMC MLB2012091000LN2 R833 6200JB8010L FILTER,EMC MLB2012091000LN2 R834 6200JB8010L FILTER,EMC MLB2012091000LN2 FILTER,EMC 60 OHM R922 6200JB8013L X1470...
Page 34
April, 2004 P/NO : 3828VD0152A Printed in Korea CANADA: LG Electronics Canada, Inc. 550 Matheson Boulevard East Mississauga, Ontario L4Z 4G3 : LG Customer Interactive Center P.O.Box 240007, 201 James Record Road Huntsville, AL 35824 ATTN : CIC...