Specifications - Shure GLX-D User Manual

Resetting the Transmitter
Restores the transmitter to the following factory settings:
• Controls = unlocked
Press and hold the transmitter link button while turning on the transmitter
until power LED goes off.
When the link button is released, the transmitter will automatically initiate
linking to find an available receiver. Press the link button on an available
receiver to relink.

Specifications

Tuning Bandwidth
2400–2483.5 MHz
Working Range
Indoor Up to 30 m (100 ft) typical, Up to 60 m (200 ft) maximum
Outdoor Up to 20 m (65 ft) typical, Up to 50 m (165 ft) maximum
Note: Actual range depends on RF signal absorption, reflection and interference.
Transmit Mode
Shure GLX-D proprietary digital
Audio Frequency Response
20 Hz – 20 kHz
Note: Dependent on microphone type
Dynamic Range
120 dB, A-weighted
RF Sensitivity
-88 dBm, typical
Total Harmonic Distortion
0.2%, typical
RF Output Power
10 mW E.I.R.P. max
Operating Temperature Range
-18°C (0°F) to 57°C (135°F)
Note: Battery characteristics may limit this range.
Storage Temperature Range
-29°C (-20°F) to 74°C (165°F)
Polarity
Positive pressure on microphone diaphragm (or positive voltage applied to tip of WA302 phone
plug) produces positive voltage on pin 2 (with respect to pin 3 of low-impedance output) and the
tip of the high impedance 1/4-inch output.
Battery Life
Up to 16 hours
Channel Count
Up to 11 maximum
GLXD1
Dimensions
90 x 65 x 23 mm(3.56 x 2.54 x 0.90in.), H x W x D (without antenna)
Power Requirements
3.7 V Rechargeable Li-Ion
Housing
Cast Metal, Black Powdercoat
Input Impedance
900 kΩ
RF Output Power
10 mW E.I.R.P. max
Transmitter Input
Connector
4-Pin male mini connector (TA4M)
Configuration
Unbalanced
Maximum Input Level
1 kHz at 1% THD
+8.4 dBV (7.5 Vp-p)
Antenna Type
Internal Monopole
Pin Assignments
TA4M
1 ground (cable shield)
2 + 5 V Bias
3 audio
4 Tied through active load to ground (On instrument adapter cable,
pin 4 floats)
GLXD2
A
Dimensions
Model A
SM58 51 mm, 2.0 in.
BETA 58 51 mm, 2.0 in.
SM86 49 mm, 1.9 in.
BETA 87A 51 mm, 2.0 in.
Weight
SM58 267 g (9.4 oz.) without batteries
BETA 58 221 g (7.8 oz.) without batteries
SM86 275 g (9.1 oz.) without batteries
BETA 87A 264 g (9.3 oz.) without batteries
Housing
Molded Plastic
Power Requirements
3.7 V Rechargeable Li-Ion
RF Output Power
10 mW E.I.R.P. max
Maximum Input Level
SM58 146 dB SPL
BETA 58 147 dB SPL
SM86 143 dB SPL
BETA 87A 147 dB SPL
14
B
B C
252 mm, 9.9 in. 37 mm, 1.5 in.
252 mm, 9.9 in. 37 mm, 1.5 in.
252 mm, 9.9 in. 37 mm, 1.5 in.
252 mm, 9.9 in. 37 mm, 1.5 in.
C