Disassembly - Sharp CD-C602 Service Manual

CD-C602,CP-C602
Caution on Disassembly
Follow the below-mentioned notes when disassembling
the unit and reassembling it, to keep it safe and ensure
excellent performance:
1. Take cassette tape and compact disc out of the unit.
2. Be sure to remove the power supply plug from the wall
outlet before starting to disassemble the unit.
3. Take off nylon bands or wire holders where they need to
be removed when disassembling the unit. After servicing
the unit, be sure to rearrange the leads where they were
before disassembling.
4. Take sufficient care on static electricity of integrated
circuits and other circuits when servicing.
CD-C602
REMOVAL
STEP
1 Top Cabinet 1. Screw ..................... (A1) x4
2. Hook ....................... (A2) x3
2 Side Panel 1. Screw ..................... (B1) x4
(Left/Right) 2. Screw ..................... (B2) x2
3. Hook ....................... (B3) x2
3 CD Tray Cover/ 1. Turn on the power supply,
CD Player Unit open the disc tray, take out
the CD tray cover, and close.
(Note 1)
2. Hook ....................... (C1) x3
3. Hook ....................... (C2) x2
4. Socket .................... (C3) x4
4 Back Board 1. Screw ..................... (D1) x3
5 Main PWB/ 1. Screw ..................... (E1) x10
Display PWB 2. Hook ....................... (E2) x2
3. Socket .................... (E3) x6
6 Front Panel 1. Screw ..................... (F1) x2
2. Hook ....................... (F2) x5
7 Tape Mechanism 1. Open the cassette holder.
2. Screw...................... (G1) x6
8 Turntable 1. Screw ..................... (H1) x1
2. Stabilizer ................ (H2) x1
9 Disc Tray 1. Screw ..................... (J1) x2
2. Guide ..................... (J2) x2
10 CD Changer 1. Screw ..................... (K1) x4
Mechanism
11 CD Mechanism 1. Screw ..................... (L1) x1
Note 1:
How to open the change manually.
1. Then, turn fully the lock lever in the arrow direction through
the hole on the loading chassis bottom in this state.
After that, push forward the CD player base. (Fig. 6-3)
2. After removing the connector for the optical pickup fromthe
connector wrap the conductive aluminium foil around the
front end of connector so as to protect the optical pickup
from electrostatic damage.
All manuals and user guides at all-guides.com

DISASSEMBLY

PROCEDURE FIGURE
6-1
6-1
6-2
6-2
7-1
7-1
7-2
7-3
7-3
7-4
7-4
CD-C602
(A1)x2
ø3x12mm
Hook
(B3x1)
(B2)x1
ø3x12mm
(B1)x2
ø3x12mm
Back Board
Side Panel
(Right)
Hook
(C2)x1
Pull
Disc Tray
CD Player Unit
1 1
(D1)x3
ø3x10mm
Back Board
Lock Lever
– 6 –
Top Cabinet
Hook
(A2x3)
Front Panel
(A1)x2
ø3x12mm
Side Panel
(Left)
Hook
(B3x1)
(B2)x1
(B1)x2
ø3x12mm
ø3x12mm
Figure 6-1
Hook
CD Tray Cover
(C1)x3
2
(C2)x1
Pull
Front Panel
(C3)x4
Main PWB
Figure 6-2
Figure 6-3
Hook