Advertisement
Introduction
The HKSP-R80 and HKSP-R81 are optional boards
designed to be installed in the PFV-SP-series Signal
Processing Unit.
The HKSP-R80 is a standalone primary station CPU
(control) board, which has not only the primary station
function but also the S-BUS subnet control function,
enabling S-BUS-to-Ethernet
R81 functions as a redundant CPU for the HKSP-R80.
Software
The following software applications are included on
the CD-ROM supplied with the HKSP-R80.
BZR-20 Routing Switcher Data Backup
Software
This software backs up various setting data of the
HKSP-R80. It can be used on an IBM PC/AT
compatible machine with Windows 98/2000/XP
installed.
BZR-21 Routing Switcher Remote Control
Software
This software has basic crosspoint switching functions
and ones to assign the terminals to operation buttons.
It permits you to conduct operation checks of your
system regardless of scale and to easily operate the
system.
It can be used on an IBM PC/AT
machine with Windows 98/2000/XP
For additional information, including the setup procedure,
see the next page.
BZR-IF810 S-BUS Subnet Control Software
Installing this software on the CPU board of the
HKSP-R80/R81, you can increase the number of units
to be connected to an S-BUS link or perform dispersed
processing.
S-BUS Primary Station Program
Use this program to return the S-BUS subnet controller
function to the factory-set status of the HKSP-R80/
R81.
........................................................................................................................
1) Ethernet is a trademark of Xerox Corporation.
2) IBM PC/AT is a trademark of IBM.
3) Windows, Windows 98, Windows 2000, and Windows XP are
registered trademarks of Microsoft Corporation in the United
States and/or other countries.
6
1)
conversion. The HKSP-
2)
-
3)
2)
-compatible
3)
installed.
Specifications
Power requirements
HKSP-R80: +12 V DC, 1.0 A
(supplied from the PFV-SP-
series unit)
HKSP-R81: +12 V DC, 700 mA
(supplied from the PFV-SP-series unit)
Dimensions (w/h/d) Main board (common to HKSP-R80/
R81) : 388.3 × 112.2 × 18 mm
(15
Connector board (HKSP-R80 only):
152.5 × 130 × 38 mm
1
(6
Mass
Main board (common to HKSP-R80/
R81): approx. 500 g (1 lb 2 oz)
Connector board (HKSP-R80 only):
approx. 400 g (14 oz)
Supplied accessories
Operation Guide (1)
Installation Guide (1)
The following items are supplied with the HKSP-R80 only:
ROM
CD-
(1)
Contents: • Installation Manual
• System Setup Manual
• BZR-20 Routing Switcher Data Backup
Software
• BZR-21 Routing Switcher Remote Control
Software
• BZR-IF810 S-BUS Sub-Net Control Software
• S-BUS Primary Station Program
75-ohm terminator (3)
T-bridge (1)
Design and specifications are subject to change
without notice.
Note
Always verify that the unit is operating properly
before use. SONY WILL NOT BE LIABLE FOR
DAMAGES OF ANY KIND INCLUDING, BUT
NOT LIMITED TO, COMPENSATION OR
REIMBURSEMENT ON ACCOUNT OF THE
LOSS OF PRESENT OR PROSPECTIVE PROFITS
DUE TO FAILURE OF THIS UNIT, EITHER
DURING THE WARRANTY PERIOD OR AFTER
EXPIRATION OF THE WARRANTY, OR FOR
ANY OTHER REASON WHATSOEVER.
× 4
×
3
1
23
/
/
/
inches)
8
2
32
× 5
× 1
1
1
/
/
/
inches)
8
8
2
Advertisement
