Sharp MD-X8 Operation Manual page 47

(Continued)
MD
REC
Synchro recording
A U X 1
W -
2
L
R
W -
A U X 1
M DWWWW
3
L
R
W -
A U X 1
M DWWWW
4
L
R
W -
A U X 1
M DWWWW
7
L
R
W -
A U X 1
M DWWWW
8
L
R
W -
38-58
REC
MD
VOLUME
DOWN UP
AUX
INPUT LEVEL
SYNCHRO
AUX
REC
T WWWWWWWWWWWWWWWW
WWW WWWW W > W
-12 -4 0
WWW WWWW W > W
-12 -4 0
T WWWWWWA . M A R KWO NW
1 WWWW 0 : 0 0 WWWWW Y
WW WWW WWWW W > W
-12 -4 0
T WWWWWWA . M A R KWO NW
1 WWWW 0 : 0 0 WWWWW Y
WW WWW WWWW W > W
-12 -4 0
0dB
T WWWW S O U N DW S Y N C R O
1 WWWW 0 : 0 0 WWWWW Y
WW WWW WWWW W > W
-12 -4 0
T WWWW S O U N DW S Y N C R O
1 WWWW 0 : 0 2 WWWWW Y
WW WWW WWWW W > W
-12 -4 0
46
H H H H H Listening to sound from an external unit
To listen to digital sound
1
Press the AUX button so that the AUX OPT. or AUX COAX
display appears.
I Each time the button is pressed, the display will change as follows:
AUX1 AUX2 AUX OPT.
2
Start playback on the external unit.
3
Adjust the sound level using the VOLUME control of this unit.
Note:
In the following cases, "DIN UNLOCK" appears and playback
sound is muted:
I When the external digital unit is off.
I When there is no digital input from the digital input jack.
To listen to analog sound
1
Press the AUX button so that the AUX 1 or AUX 2 display
appears.
I When connecting an external unit to the "MD IN/AUX1 " terminal at the
front of the main unit, select "AUX1". When connecting to the "AUX2"
terminal at the rear of the main unit, select "AUX2".
2
Adjust the input sound level using the INPUT LEVEL control.
I When the INPUT LEVEL control is turned counterclockwise, no sound
is obtained.
3
Start playback on the external unit.
4
Adjust the volume using the INPUT LEVEL control and VOL-
UME control on this unit.
H H H H H Synchro recording
MD recording will start automatically as soon as playback is
started on the external unit. This applies to both digital inputs and
analog inputs.
I The space-cut function will work automatically during synchro record-
ing.
I Synchro recording is available only for recordings from an external
unit.
1
Load a recordable MiniDisc.
2
Press the AUX button to select the auxiliary input .
I Select the input that corresponds to the terminals where the external
unit you want to record from is connected.
I Each time the button is pressed, the display will change as follows:
AUX1 AUX2 AUX OPT.
To record analog signals, perform steps 3 - 8.
To record digital signals, perform steps 6 - 8.
3
Press the REC button, then start playback on the external unit.
4
Adjust the recording level using the INPUT LEVEL control.
I The maximum level should not exceed 0 dB.
5
Stop playback on the external unit.
6
Press the MD H button.
7
Press the SYNCHRO REC button.
8
Start playback on the external unit.
I Recording will start automatically.
I To stop recording halfway, press the MD H button.
46
98.6.23, 10:34 AM
AUX COAX PHONO
AUX COAX PHONO