Advertisement
FEATURES OF SHARK ELECTRONIC IRON
3
1
2
1. BURST OF STEAM BUTTON
Burst of steam provides extra,
sudden bursts of steam which aid in
removing stubborn wrinkles from
fabrics such as denim, cotton or
linen.
2. ATOMIZER SPRAY
BUTTON
Pressing this button provides a
defined jet of spray which gently
moistens fabric.
3. VARIABLE STEAM
CONTROL
Minimum to maximum steaming
for different materials. Self
cleaning feature flushes internal
sole plate with water.
4. ANTI-DRIP FUNCTION
Cuts off water when the
iron temperature is too
low.
5. BUILT-IN ANTI-CALCIUM
FILTER
Prevents calcium build-up
and prolongs the life of the
iron.
6. STAINLESS STEEL
SOLEPLATE
Provides maximum glide-
ability and heat retention.
LED Display Panel
7. LED DISPLAY PANEL
Displays the fabric setting
(left) and the temperature
indicators (right).
8. WATER FILLING INLET
The cover prevents dust and
foreign matter from entering
the water tank. It also stops
any water from spilling during
ironing.
9. PIVOT CORD
For left or right handed use.
Pivots up and down;
prevents dragging along the
fabric. The flexible cord
protector protects the cord
from fraying.
3
OPERATING INSTRUCTIONS
This appliance is for HOUSEHOLD USE
ONLY and may be plugged into any
120V AC polarized electrical outlet. Do
not use any other type of outlet.
FABRIC & TEMPERATURE
INDICATORS
Press on the Electronic Temperature
Control to select the desired fabric
setting. The red lights at the left of the
LED Display Panel will light up.
At the same time, the temperature
indicator lights on the right side of the
LED Display Panel will start to flash.
They will stop flashing when the iron
reaches the selected temperature.
DRY IRONING
For dry ironing, turn the variable steam
control dial all the way to the right to "0".
This will cut off the steam flow if water is
in the water tank. All marked fabric
settings on the LED Display Panel can
be used for dry ironing.
1. Plug the cord into a polarized, 120V
AC electrical outlet. The power "ON"
light will come on, indicating that the
iron is receiving power.
2. Press on the electronic temperature
control button to select the desired
fabric/temperature setting. Turn the
variable steam control to "0".
(See "Ironing Guide" for a guide to
temperature selection.)
3. Place iron on its heel (on a stable,
protected surface) while iron is
warming to desired temperature.
STEAM IRONING
CAUTION
DO NOT aim iron at
face, towards yourself, or
anyone else while using or adjusting
steam. Burns or serious injury may
occur.
WARNING
Before filling the iron
with water, be sure the iron is not
plugged into the electrical outlet. The
iron may be filled with water while it
is hot.
CAUTION
TO PREVENT THE
RISK OF BURNS, use caution
when filling iron with water. Burns
can occur from touching hot metal
parts, hot water, or steam.
NOTE: Because of the soleplate design,
ordinary tap water may be used with this
iron. However, in very hard water areas,
we recommend using distilled or
demineralized water.
WARNING
: Never fill the iron
with fabric conditioner, starches
or any other liquid, as these will
damage the steam mechanism. Do
not use contaminated water.
1. Open the water filling inlet cover.
Holding the iron at a slight angle,
pour water slowly into the water
filling inlet. (Fig. 1) Fill tank to
desired level or to the "MAX" water
level marking using the water filling
flask. (When the iron is upright, the
see-through water tank allows you to
gauge the amount of water.) DO
NOT overfill the tank. When finished
filling the iron with water, close the
water inlet cover before continuing.
Fig. 1
2. Plug the cord into a polarized, 120V
AC electrical outlet.
3. Press on the electronic temperature
control button to select the desired
fabric and temperature setting. Turn
the variable steam control dial to
the desired steam setting. (See
"Ironing Guide" for a guide to
temperature selection.)
4
Advertisement
