Craftsman 315.17473 Owner's Manual page 3

RULES FOR SAFE OPERATION (Continued)
18. DISCONNECT TOOLS. When not in use, before 29.
servicing, or when changing attachments, blades,
bits, cutters, etc., all tools should be disconnected
from power supply. 30.
19. REMOVE ADJUSTING KEYS AND WRENCHES.
Form habit of checking to see that keys and adjust-
ing wrenches are removed from tool before turning
it on.
20. AVOID ACCIDENTAL STARTING. Don't carry
plugged-in tools with finger on switch. Be sure
switch Is off when plugging in.
21. MAKE SURE YOUR EXTENSION CORD IS IN
GOOD CONDITION. When using an extension
cord, be sure to use one heavy enough to carry the
current your product will draw. An undersized cord 31.
will cause a drop in line voltage resultingin loss of
power and overheating. A wire gage size (A.W.G.)
of at least 14 is recommended for an extension 32.
cord 100 feet or less in length. A cord exceeding
100 feet is not recommended. If in doubt, use the 33.
next heavier gage. The smaller the gage number,
the heavier the cord.
22. OUTDOOR USE EXTENSION CORDS. When tool ,
is used outdoors, use only extension cords suit- 34.
able for use outdoors. Outdoor appi'ovedcordsare
marked with the suffix W-A, for example - SJTW-A
or SJOW-A. 35.
23. KEEP CUTTERS CLEAN AND SHARP. Sharp
cutters minimize stalling and kickback. 36.
24, KEEP HANDS AWAY FROM CUTTING AREA.
Keep hands away from cutters. Do not reach un-
derneath work while cutter is rotating. Do not at-
tempt to remove material while cutter is rotating.
25. NEVER USE IN AN EXPLOSIVE ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
26. INSPECT TOOL CORDS PERIODICALLY and if 37.
damaged, have repaired at your nearest Sears
Repair Center. Stay constantly aware of cord loca-
tion.
27. INSPECT EXTENSION CORDS PERIODICALLY
and replace if damaged.
28. KEEP HANDLES DRY, CLEAN, AND FREE
FROM OIL AND GREASE. Always use a clean
cloth when cleaning. Never use brakq fluids, gaso-
line, petroleum-based products or any strong sol-
vents to clean your tool.
STAY ALERT. Watch what you are doing and use
common sense. Do not operate tool when you are
tired. Do not rush.
CHECK DAMAGED PARTS. Before further use of
the tool, a guard or other part that is damaged
shouldbe carefully checked to determine that it will
operate properly and perform its intended function.
Check for alignment of moving pads, binding of
moving parts, breakage of parts, mounting, and
any other conditions that may affect its operation.
A guard or other part that is damaged should be
propedy repaired or replaced by an authorized
service center unless indicated elsewhere in this
instructionmanual.
DO NOT USE TOOL IF SWITCH DOES NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
Inspectfor and remove all nails from lumber before
routing.
DO NOT USE TOOL UNDER "BROWN-OUT" OR
OTHER LOW VOLTAGE CONDITIONS. Also, do
not use with any device that could cause the power
supply voltage to change.
DRUGS, ALCOHOL, MEDICATION. Do not oper-
ate tool while under the influence of drugs, alcohol,
or any medication.
WHEN SERVICING USE ONLY IDENTICAL
CRAFTSMAN REPLACEMENT PARTS.
POLARIZED PLUGS. To reduce the risk of electric
shock, this tool has a polarized plug (one blade is
wider than the other). This plug will fit in a polarized
outletonlyone way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does not fit, contact
a qualified electricianto install the proper outlet. Do
not change the plug in any way.
SAVE THESE INSTRUCTIONS. Review them fre-
quently and use them to instruct others who may
use this tool. If you loan someone this tool, loan
them these instructionsalso.
ll
Illl IIIII =lllll I ,llll I I,I
The operation of any router can result In foreign objects being thrown Into your eyes, which can !
result In severe eye damage. Before beginning powertool operation, always wear safety goggles |
or safety glasses with side shields and a full face shield when needed. We recommend Wide |
Vision Safety Mask for use over eyeglasses or atandard safety glasses with side shields, i
available at Sears Reta!!Stores. J
Page 3