Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Sears Craftsman 113.24611
Summary of Contents for Sears Craftsman 113.24611
- Page 1 Sears CAUTION: Read GENERAL ADDITIONAL SAFETY INSTRUCTIONS carefu|iy Sold SEARS, ROEBUCK SIMPSONS-SEARS Part No. 71 176 COMMERCIAL 15-I/2 INCH DRILL PRESS assembly operating repair parts CO., Chicago, LIMITED, Toronto, 60684 U.S.A. Ontario, Canada. P,:ir,t_d i_ i; _ ;_...
- Page 2 general safely instructions 1. KNOW YOUR POWER TOOL Read owner's manual carefully. application and limitations as well as the specific potential hazards peculiar to this tool. GROUND TOOLS This tool is equipped with an approved 3-conductor cord and a 3-prong grounding type plug to fit the proper grounding type receptacle.
-
Page 3: General Safety Instructions For Power Tools
IT IS COMPLETELY ASSEMBLED ACCORDgNG TO THE iNSTRUCTIONS HAVE READ UNDERSTAND FOLLOWING: 1. General Safety Instructions for PowerTools 2. Getting to Know Your Drill Press 3. Basic Drill PressOperation 4. Adjustments 5. Maintenance Stabiaity of Drill Press If there is any tendency... - Page 4 Apply a coat of automobile wax to the table. Wipe all parts thoroughly with a clean dry cloth. instructions for drill presses 12. Think Safety. Safety is a combination of operator common sense and alertness at all times when the drill pressis being used. READ WARNING: BEFORE...
-
Page 5: Specifications
MOTOR SPECIFICATIONS This drill press is designed to use a 1725 Do not use any motor that runs faster than is wired operation 1t0-120 alternating current. IT MUST BE CONVERTED OPERATE VOLTS, EVEN RECOMMENDED MOTORS DUAL THESE CRAFTSMAN... -
Page 6: Assembly
ALL ASSEMBLY STEPS ARE COMPLETED. 1. Unwind the power cord. 2. Make sure the quill lock handle is tight. 3. Stand on the left side of the drill pressand LOOSEN the HEAD LOCK HANDLE. Raise the HEAD about HALF WAY up the column. -
Page 7: Installing Feed Handles
Apply a light film of oil such as Sears household the spindle nose. Place chuck on the spindle nose locking collar up as far as it will go. Insert a piece of 5/16 in. dia. STEEL the holes in the chuck body. -
Page 8: Installing The Depth Stop
Tighten the Table Lock Handle. Locate the two clamps bolts from the paper tube when you first your drill press. These parts make up the TABLE SUPPORT Position the TABLE SUPPORT COLLAR the table and tighten the bolts. Loosen the HEAD LOCK HANDLE. -
Page 9: Installing Motor Pulley
9.Gently push down on theFEED HANDLES untilthe head r aises upwards as faras it willgo. DONOT RELEASE FEED HANDLE. 10, T IGHTEN THEHEADLOCK HANDLE ANDTHE QUILLLOCK HANDLE. 11. H OLDontothe Feed Handle a ndUNLOCK t hequill lockhandle. 12.Letthequillreturn totheUP position inthehead, 13. -
Page 10: Mounting The Motor
assembly NOTE: When using motors which have 1/2 in. dia. shafts, place the adapter sleeve (furnished with the motor) on the shaft so that the slot in the sleeve is over the flat spot. Insert the shaft key (furnished with motor) into the grooves in the shaft and pulley so that the end of the key is even with the end of the shaft, Tighten the set screw. - Page 11 CAUTION: If you are using a DOUBLE SHAFT motor. Make sure the SHAFT PROTECTOR is installed. NEVER USE THE DRILL PRESS WITH THE UNUSED SHAFT EXPOSED. in" on the two screws BEND the loose parts...
-
Page 12: Belt Tension Rod
3. Place the belt on the pulleys. 4. Put a dab of grease such as Sears gear case lubricant on the rubber tip of the BELT TENSIONING 5. Loosen HEX HEAD SCREW with a 7/16 in. wrench ... -
Page 13: On-Off Switch
RACK (TEETH) CHUCK __-_ CHUCK QUILL SPINDLE ASSEMBLY INSIDE OF DRILL PRESS CHUCK is used to tighten chuck. It has a spring loaded EJECTOR it out of the chuck when you let go of it. When not in use, ALWAYS... -
Page 14: Getting To Know Your Drill Press
To turn drill Insert finger under switch lever and pull. TO turn drill OFF Push lever in. In an emergency; ...thedrill bit BINDS STOPS . .. or tends to tear the workpiece QUICKLY turn the drill by hitting... -
Page 15: Basic Drill Press Operation
Move the POINTER all the way down thumb screw. Tighten the STOP NUT against the pointer. Unlock the quill. Feed the drill into the workpiece until the pointer. ANOTHER WAY-- With the switch OFF, bring the drill the TIP touches of the WORKPIECE •.. -
Page 16: Hole Location
When drilling effort "\ VISE to cut. SLOWLY might cause the drill to burn RAPIDLY might stop the motor to SLIP tear the workpiece LOOSE or BREAK the drill bit. metal Sears Thread-cutting cause... -
Page 17: Adjustments
diustments WARNeNG: FOR YOUR OWN SAFETY "OFF" REMOVE PLUG FROM POWER SOURCE OUTLET BEFORE MAKING ANY ADJUSTMENTS. DEPTH SCALE When the quill is in the UPPERMOST SURFACE OF THE FEED STOP POINTER line with "0" graduation on the DEPTH LOOSEN both mounting reposition... -
Page 18: Maintenance
They require TURN SWITCH POWER SOURCE Periodically lubricate LUBRICATING and the RACK USE Sears Gear Case Lubricant. accumulate inside Lower quill the quill. to the table Use a small the inside of the hole in the spindle in any way,... -
Page 19: Recommended Accessories
2. Dry Spindle 3. Loose spindle or motor Drill Burns. 1. Incorrect 2. Chips not coming out of hole. 3. Dull Drill 4. Feeding too slow, 5, Not lubricated. 6. Drill Hard grain in wood Drill leads off... hole not round. - Page 20 PARTS LIST FOR CRAFTSMAN SEE FIGURE ALL WIRES SNAP INTO WIRE SADDLE I--.83 30 64 DRILL PRESS MODEL NO. 113.2461! T_IO 11 12 mmll €) "0 SEE FIGURE...
-
Page 21: Mount, Motor
*Pin, Roll 3/16 x 2-1/4 60193 71108 Hub Assembly (Includes Key Nos. 42 & 43) 71109 Spring 60197 Pin, Roll 1/4 x 1-1/8 71139 *Standard DRILL PRESS MODEL NO, 113.24611 FIGURE PARTS LIST Part 38546 Knob 71110 60263 Grip 60265 Handle, Lock 38627... - Page 22 15---"--_ 16.------_ __._. Figure PARTS LIST FOR CRAFTSMAN COMMERCIAL MODEL No. 113.24611 Part FIGURE ,_, r = 71128 144987 71069 STD 610807 60158 71071 71070 71072 71097 60227 71162 71089 71090 STD 315253 71091 18414 *Standard Hardware Item "=! DRILL PRESS "O...
- Page 23 PARTS LIST FOR CRAFTSMAN COMMERCIAL MODEL No. 113.24611 10---_ DRILL PRESS FIGURE 3 -- 71158 SPINDLE ASM. STOP PARTS LIST Part Description 71158 Spindle Assembly, Stop 60278 Ring, Retaining, 5/8 71127 Bearing, Ball 71159 Tube, Quill 60199 Gasket, Quill 60200...
-
Page 24: Repair Parts
Sears Co. stores. Be sure you call or visit. press will be found on a plate ALWAYS GIVE COMMERCIAL PRESS from Sears Service Center need stocked transmitted to a Sears 60684 U.S.A. Printed in U.S.A. 4/78...