Related Manuals for Seagate PIPELINE HD MINI SERIES SATA ST9320328CS
Summary of Contents for Seagate PIPELINE HD MINI SERIES SATA ST9320328CS
- Page 1 Product Manual Pipeline HD Mini Series SATA ST9500323CS ST9320328CS 100560196 Rev. E December 2010 ST9250311CS ST91603110CS...
-
Page 2: Revision History
United States and/or other countries. Pipeline HD, SeaTools and SeaTDD are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners. - Page 3 Pipeline HD Mini Series SATA Product Manual, Rev. E...
- Page 4 Pipeline HD Mini Series SATA Product Manual, Rev. E...
-
Page 5: Table Of Contents
Introduction..............1 About the Serial ATA interface . - Page 6 Pipeline HD Mini Series SATA Product Manual, Rev. E...
-
Page 7: List Of Figures
Figure 1. Typical +5V only startup and operation current profile ....... 8 Figure 2. -
Page 9: Seagate Technology Support Services
• Authorized Service Centers For information regarding Warranty Support, visit http://www.seagate.com/www/en-us/support/warranty_&_returns_assistance For information regarding data recovery services, visit For Seagate OEM and Distribution partner portal, visit For Seagate reseller portal, visit http://spp.seagate.com Pipeline HD Mini SATA Product Manual, Rev. E http://www.seagate.com/www/en-us/about/contact_us/... - Page 10 Pipeline HD Mini SATA Product Manual, Rev. E viii...
-
Page 11: Introduction
• 5,400-RPM spindle speed. • 8-Mbyte buffer. • Quiet operation. Fluid Dynamic Bearing (FDB) motor. • High instantaneous (burst) data rate 3.0 Gbits/sec default, 1.5 Gbit/sec available via Seagate specific SCT com- mand. • Perpendicular recording technology. • State-of-the-art cache and on-the-fly error-correction algorithms. - Page 12 In addition, Serial ATA makes the transition from parallel ATA easy by providing legacy software support. Serial ATA was designed to allow you to install a Serial ATA host adapter and Serial ATA disc drive in your current sys- tem and expect all of your existing applications to work as normal. The Serial ATA interface connects each disc drive in a point-to-point configuration with the Serial ATA host adapter.
-
Page 13: Drive Specifications
625,142,448 1,490k 265k 5,400 1,175 300 default / 150 available via Seagate specific SCT command SATA 1.0, Serial ATA Revision 2.6 PIO modes 0–4 Multiword DMA modes 0–2 Ultra DMA modes 0–6 9.5 +/- 0.2 mm (0.374 +/- .0078 inches) 69.85 mm +/- 0.25 mm (2.75 +/- 0.0098 inches) - Page 14 To determine the warranty for a specific drive, use a web browser to access the following web page: support.seagate.com/customer/warranty_validation.jsp You will be asked to provide the drive serial number, model number (or part number) and country of purchase. After submitting this information, the system will display the warranty information for your drive.
-
Page 15: Formatted Capacity
Formatted capacity Model ST9500323CS ST9320328CS ST9250311CS ST91603110CS *One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. 2.2.1 LBA mode When addressing these drives in LBA mode, all blocks (sectors) are consecutively numbered from 0 to n–1, where n is the number of guaranteed sectors as defined above. -
Page 16: Physical Organization
Number of discs Serial ATA (SATA) Perpendicular 1,490k 265k 5,400 1,175 300 default / 150 available via Seagate specific SCT command 8 Mbytes (8,192 kbytes) 9.5 +/-0.2 0.374 +/-0.0078 69.85 +/-0.25 2.75 +/-0.0098 100.35 +0.55 / -0.25 3.957 +0.079 / -0.0098 110 grams 0.243 pounds... -
Page 17: Start/Stop Times
Table 2: Typical seek times Track-to-track (typical) Average (typical) Full-stroke (max) Average latency 5.56 These drives are designed to consistently meet the seek times represented in this manual. Physical Note. seeks, regardless of mode (such as track-to-track and average), are expected to meet the noted val- ues. - Page 18 During Standby mode, the drive accepts commands, but the drive is not spinning, and the servo and read/write electronics are in power-down model Table 3: DC power Power dissipation ST9500323CS and ST9320328CS Spinup (max) 1 amp Seek 1.54 watts IDEMA 3 Stream 1.7 watts Idle, performance* 1.5 watts...
-
Page 19: Conducted Noise
2.9.2 Conducted noise Input noise ripple is measured at the host system power supply across an equivalent 15-ohm resistive load on the +5 volt line. Using 5-volt power, the drive is expected to operate with a maximum of 100 mV peak-to-peak square-wave injected noise at up to 10 MHz. -
Page 20: Environmental Specifications
• Idle and Standby timers Each time the drive performs an Active function (read, write or seek), the standby timer is reinitialized and begins counting down from its specified delay times to zero. If the standby timer reaches zero before any drive activity is required, the drive makes a transition to Standby mode. -
Page 21: Shock
2.10.5 Shock All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mount- ing screws. Shock may be applied in the X, Y or Z axis. 2.10.5.1 Operating shock These drives comply with the performance levels specified in this document when subjected to a maximum operat- ing shock of 350 Gs based on half-sine shock pulses of 2 msec. -
Page 22: Electromagnetic Immunity
Seagate follows the ECMA-74 standards for measurement and identification of PDTs. An exception to this process is the use of the absolute threshold of hearing. Seagate uses the lower limit for the threshold curve* to discern tone audibility and to compensate for the inaudible components of sound prior to computation of tone ratios according to Annex D of the ECMA-74 standards. -
Page 23: Reliability
55022, Class B and the immunity levels are defined by EN 55024. Drives are tested in representative end-user systems. Although CE-marked Seagate drives comply with the direc- tives when used in the test systems, we cannot guarantee that all systems will comply with the directives. The drive is designed for operation inside a properly designed enclosure, with properly shielded I/O cable (if necessary) and terminators on all unused I/O ports. -
Page 24: Fcc Verification
Seagate has tested this device in enclosures as described above to ensure that the total assembly (enclosure, disc drive, motherboard, power supply, etc.) does comply with the limits for a Class B computing device, pursu- ant to Subpart J, Part 15 of the FCC rules. -
Page 25: European Union Restriction Of Hazardous Substances (Rohs)
The silver, cop- per, nickel and gold films used in Seagate products are especially sensitive to the presence of sulfide, chloride, and nitrate contaminants. Sulfur is found to be the most damaging. In addition, electronic components should never be exposed to condensing water on the surface of the printed circuit board assembly (PCBA) or exposed to an ambient relative humidity greater than 95%. - Page 26 Pipeline HD Mini Series SATA Product Manual, Rev. E...
-
Page 27: Configuring And Mounting The Drive
Configuring and mounting the drive This section contains the specifications and instructions for configuring and mounting the drive. Handling and static-discharge precautions After unpacking, and before installation, the drive may be exposed to potential handling and electrostatic discharge (ESD) hazards. Observe the following standard handling and static-discharge precautions: Caution: •... -
Page 28: Drive Mounting
For installations which require cables, you can connect the drive as illustrated in Figure 2. inter ace connector inter ace ca le ower ca le Figure 2. Attaching SATA cabling Each cable is keyed to ensure correct orientation. Drive mounting You can mount the drive using four screws in the side-mounting holes or four screws in the bottom-mounting holes. - Page 29 Measurements shown in Figure 3 are in inches. Figure 3. Mounting dimensions—top, side and end view Pipeline HD Mini Series SATA Product Manual, Rev. E...
- Page 30 Pipeline HD Mini Series SATA Product Manual, Rev. E...
-
Page 31: Serial Ata (Sata) Interface
Serial ATA (SATA) interface These drives use the industry-standard Serial ATA interface that supports FIS data transfers. It supports ATA pro- grammed input/output (PIO) modes 0–4; multiword DMA modes 0–2, and Ultra DMA modes 0–6. The drive also supports the use of the IORDY signal to provide reliable high-speed data transfers. For detailed information about the Serial ATA interface, refer to the “Serial ATA: High Speed Serialized AT Attach- ment”... -
Page 32: Supported Ata Commands
Table 7: Serial ATA connector pin definitions Segment Function Definition 3.3V power 3.3V power 3.3V power, pre-charge, 2nd mate Ground 1st mate Ground 2nd mate Ground 2nd mate 5V power, pre-charge, 2nd mate 5V power Power 5V power Ground 2nd mate Reserved The pin corresponding to P11 in the backplane receptacle connector is also reserved The corresponding pin to be mated with P11 in the power cable receptacle connector shall... - Page 33 Command name Device Configuration Identify Device Configuration Set Download Microcode Execute Device Diagnostics Flush Cache Flush Cache Extended Identify Device Initialize Device Parameters Read Buffer Read DMA Read DMA Extended Read DMA without Retries Read Long with Retries Read Long without Retries Read Multiple Read Multiple Extended Read Native Max Address...
- Page 34 Command name S.M.A.R.T. Enable Operations S.M.A.R.T. Enable/Disable Auto Offline S.M.A.R.T. Enable One Attribute Modification S.M.A.R.T. Execute Offline S.M.A.R.T. Read Attribute Thresholds S.M.A.R.T. Read Data S.M.A.R.T. Read Log Sector S.M.A.R.T. Return Status S.M.A.R.T. Save Attribute Values S.M.A.R.T. Write Attribute Thresholds S.M.A.R.T. Write Attribute Values S.M.A.R.T.
-
Page 35: Identify Device Command
Command name Security Erase Unit Security Freeze Lock Security Disable Password 4.3.1 Identify Device command The Identify Device command (command code EC power up. The data is organized as a single 512-byte block of data, whose contents are shown in the table on page 27. - Page 36 Word Description Number of current logical cylinders Number of current logical heads Number of current logical sectors per logical track 57–58 Current capacity in sectors Number of sectors transferred during a Read Multiple or Write Multiple command 60–61 Total number of user-addressable sectors This field contains a value that is one greater than the total num- ber of user-addressable sectors.
- Page 37 Free Fall Protection support (bit 5) Free Fall Protection enable/disable (bit 5) 121–127 ATA reserved Security status 129–159 Seagate-reserved 160–254 ATA-reserved Integrity word See the bit descriptions below for words 63, 88, and 93 of the Identify Drive data: Note.
-
Page 38: Set Features Command
Ultra DMA mode 1 is currently active. Ultra DMA mode 2 is currently active. Ultra DMA mode 3 is currently active. Ultra DMA mode 4 is currently active. Ultra DMA mode 5 is currently active. Ultra DMA mode 6 is currently active. Word 93 1 = 80-conductor cable detected, CBLID above V 0 = 40-conductor cable detected, CBLID below V... -
Page 39: Commands
SeaTools diagnostic software activates a built-in drive self-test (DST S.M.A.R.T. command for D4 unnecessary drive returns. The diagnostic software ships with all new drives and is also available at: http://seatools.seagate.com. This drive is shipped with S.M.A.R.T. features disabled. You must have a recent BIOS or software package that supports S.M.A.R.T. - Page 40 Pipeline HD Mini Series SATA Product Manual, Rev. E...
- Page 41 Index ACA 14 acoustics 4 Active mode 9 Address 23 AFR 13 Agency certification 13 Altitude 10 Altitude, nonoperating 4 Altitude, operating 4 ambient temperature 6 Annualized Failure Rate 13 Annualized Failure Rate (AFR) 4 Areal density 3 ATA commands 22 ATA data-transfer modes supported 3 Australia/New Zealand Standard AS/NZ CISPR22 14 Australian Communication Authority (ACA) 14...
- Page 42 Guaranteed sectors 3 guaranteed sectors 5 handling 17 Handling precautions 17 heads 5 Height 3 height 6 Humidity 10 humidity 4 I/O data-transfer rate 3 I/O duty cycle 13 IDEMA 3 Stream power 4 Identify 23 Identify Device 23 Identify Device command 25 Idle 8 Idle and Standby timers 10 Idle Immediate 24...
- Page 43 Read Sectors without Retries 23 Read Stream DMA Extended 23 Read Stream Extended 23 Read Verify Sectors 23 Read Verify Sectors Extended 23 Read Verify Sectors without Retries 23 Read/write heads 5 read/write power and current 7 Recording density 3 Recording method 6 Recording technology 6 Relative humidity 4...
- Page 44 Pipeline HD Mini Series SATA Product Manual, Rev. E...
- Page 46 Seagate Technology LLC 920 Disc Drive, Scotts Valley, California 95066-4544, USA Publication Number: 100560196, Rev. E, Printed in USA...