Related Manuals for Consort EV1450
Summary of Contents for Consort EV1450
- Page 1 MANUAL HANDLEIDING MODE D’EMPLOI ANLEITUNG EV1450 EV2150 EV2310 EV2320 EV2650 EV3020 EV3330 EV3610 EV3620 February 2015...
-
Page 2: Table Of Contents
Index General informations..................1 Very important.....................2 Procedure....................3 Setup......................3 Language........................3 Contrast........................3 Date/Time........................4 Password........................4 Detection........................5 Data........................... 5 Info..........................5 Method programming..................6 Manual programming..................8 Running condition..................9 Display........................9 Buttons........................9 Adjusting parameters...................... 9 End of procedure......................10 Alarm messages......................10 USB Digital Port..................10 Frequently Asked Questions................11 Warranty....................13... -
Page 3: General Informations
This instrument (excluding all accessories) is warranted against defective material and workmanship for a period of thirty-six (36) months from the date of shipment ex factory. Consort will repair all defective equipment returned to it during the warranty period without charge, provided the equipment has been... -
Page 4: Very Important
Manual Power Supplies Very important This electrophoresis power supply is a high technology instrument available in several versions. As it is capable of giving dangerous voltage levels by which high power is involved, we suggest that you take a few moments to read this manual thoroughly. Although this instrument is equipped with all necessary safety features against abuse and other accidental failures, caution should be exercised when working with high voltage equipment. -
Page 5: Procedure
Manual Power Supplies Procedure? This is the main menu that is shown after powering the device and has 3 options: PROCEDURE? MANUAL METHOD SETUP 1. MANUAL To start a regular procedure with fixed parameter limits for Voltage, Current, Power and Timer. -
Page 6: Date/Time
Manual Power Supplies System: Date/Time This device has a precise real time clock built in. The real time clock is used for GLP reports and data recording purposes. The date and the time can be adjusted. 1. Follow these steps to select DATE/TIME and press : LANGUAGE PROCEDURE? SYSTEM... -
Page 7: Detection
4. Decide whether or not the instrument should proceed with the experiment for the remaining time after a power failure and press . Data To be added, check our website (www.consort.be/wiki) for firmware updates of the instrument. This feature will allow to log all information about the executed procedures. Info... -
Page 8: Method Programming
Manual Power Supplies Method programming Method programming permits to store up to 9 different methods, each with 9 steps, of frequently used parameters in the non-volatile memory for future recall. Each step is able to recall a next one, provi- ding a flexible multiple step function for special techniques. - Page 9 Manual Power Supplies 10. Enter the desired power limit 11. Enter the desired timer unit (h or kVh) and press : and press : METHOD 1|1 METHOD 1|1 POWER TIMER UNIT This limit is automatically set to maximum and cannot be changed in case of a voltage gradient step: 12.
-
Page 10: Manual Programming
Manual Power Supplies Manual programming Manual programming permits to set voltage, current, power and time limits for a simple routine electrophoresis run. Parameters can be changed temporarily without interrupting the run. 1. Verify if the instrument is switched off. 2. Connect the electrophoresis tank to the instrument. 3. -
Page 11: Running Condition
Manual Power Supplies Running condition Display 85 mA 51 W 00:29:33 h 17/12/15 10:36:18 When running an experiment, the display allows to see the actual parameters. It is divided into three fields: The upper left field shows : • ◦... -
Page 12: End Of Procedure
TECHNICAL PROBLEM • Failure in the electronics. See Support on www.consort.be. You could also try a general RESET: switch the instrument on while holding pressed. Attention! All stored programs and data will be erased! USB Digital Port This power supply has a digital USB port allowing to interface with a computer. -
Page 13: Frequently Asked Questions
Manual Power Supplies Frequently Asked Questions What are the relations between Voltage, Current, Power and Resistance? Power (W) = Voltage (V) x Current (A) Resistance ( ) = Voltage (V) / Current (A) How does a power supply react after pressing RUN? The internal generator will start building up the high voltage at the output terminals while voltage and current are constantly measured and power calculated. - Page 14 Manual Power Supplies Specifications Rev. 1605...
-
Page 15: Warranty
The original purchase order numbers, Consort invoice numbers and serial numbers of the products must be provided. CONSORT will repair all defective equipment returned to it during the warranty period without charge (CIF Turnhout prepaid by sender), provided the equipment... -
Page 16: Ce Declaration
DECLARATION OF CONFORMITY We declare under our sole responsibility that the product Electrophoresis Power Supplies content of the type numbers EV1450 EV2150 EV2310 EV2320 EV2650 EV3020 EV3330 EV3610 EV3620 to which this declaration relates is in conformity with the following standards of the European Directives...