Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Chauvet DJ Intimidator SCAN 110
Summary of Contents for Chauvet DJ Intimidator SCAN 110
- Page 1 User Manual...
-
Page 2: Table Of Contents
Configuration (Settings) ................Pan Reverse......................Tilt Reverse ......................Fine-Tune Function ....................Firmware Version ....................Factory Reset ......................Master/Slave Mode ..................5. Maintenance................Product Maintenance ..................6. Technical Specifications ............7. Returns..................8. Contact Us .................. Intimidator Scan 110 User Manual Rev. 1... -
Page 3: Before You Begin
Electronically published by Chauvet in the United States of America. CHAUVET, the Chauvet logo, and Intimidator Scan 110 are registered trademarks or trademarks of Chauvet & Sons LLC (d/b/a Chauvet and Chauvet Lighting) in the United States and other countries. Other company and product names and logos referred to herein may be trademarks of their respective companies. -
Page 4: Safety Notes
Keep this User Manual for future use. If the product is sold to someone else, be sure that they also receive this document. Page 2 of 14 Intimidator Scan 110 User Manual Rev. 1... -
Page 5: Introduction
Product Overview Safety Cable Pass-through Mounting Mirror Bracket Lens In/Out Display Menu Power Power Buttons Product Dimensions 10.6 in 269 mm 4.7 in 7.5 in 119.3 mm 190.5 mm Intimidator Scan 110 User Manual Rev. 1 Page 3 of 14... -
Page 6: Setup
3. Setup AC Power The Intimidator Scan 110 has an auto-ranging power supply and it can work with an input voltage range of 100 to 240 VAC, 50/60 Hz. To determine the product’s power requirements (circuit breaker, power outlet, and wiring), use the current value listed on the label affixed to the product’s back panel, or refer to the product’s specifications chart. -
Page 7: Mounting
Before mounting the product, read and follow the safety recommendations indicated in the Safety Notes. Orientation The Intimidator Scan 110 may be mounted in any position; however, make sure adequate ventilation is provided around the product. Rigging • Before deciding on a location, always make sure there is easy access to the product for maintenance and programming. -
Page 8: Operation
Factory LoAd Loads factory defaults Reset Configuration (DMX) The Intimidator Scan 110 works with a DMX controller. Information about DMX is in the CHAUVET DMX Primer, which is available from the Chauvet website http://www.chauvetlighting.com/downloads/ DMX_Primer_rev05_WO.pdf. Starting Address When selecting a starting DMX address, always consider the number of DMX channels the selected DMX mode uses. -
Page 9: Dmx Personalities
Operation DMX Personalities The Intimidator Scan 110 has two DMX personalities: a 11-channel personality, and a 5-channel personality. To select a DMX personality, follow the instructions below. 1. Press <MENU> repeatedly until ChMd shows on the display. 2. Press <ENTER>. -
Page 10: 5Ch
200 227 Gobo 7 228 255 Gobo 8 000 007 On Strobe 008 250 Strobe, slow to fast 251 255 On Dimmer 000 255 0–100% Page 8 of 14 Intimidator Scan 110 User Manual Rev. 1... -
Page 11: Configuration (Standalone)
3. Use <UP> or <DOWN> to select Soud. 4. Press <ENTER>. Sound Sensitivity To set the sound sensitivity on the Intimidator Scan 110, follow the instructions below: 1. Press <MENU> repeatedly until SEnS shows on the display. 2. Press <ENTER>. -
Page 12: Fine-Tune Function
Operation Fine-Tune Function The Intimidator Scan 110 is capable of fine-tuning the motor for the Pan option (for X-axis), Gobo option, and Tilt option (for Y-axis). To access the fine-tuning options: 1. Press <MENU>. 2. Press and hold <ENTER> for 3 seconds. -
Page 13: Maintenance
7. Gently polish the transparent surfaces until they are free of haze and lint. Always dry the transparent surfaces carefully after cleaning them. Do not spin the cooling fans using compressed air because they could be damaged. Intimidator Scan 110 User Manual Rev. 1 Page 11 of 14... -
Page 14: Technical Specifications
Cooling System 104 °F (40 °C) Fan-assisted convection I/O Connector Channel Range 3-pin XLR 5 or 11 Ordering Product Name Item Code UPC Number Intimidator Scan 110 07021495 781462218430 Page 12 of 14 Intimidator Scan 110 User Manual Rev. 1... -
Page 15: Returns
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be your responsibility. FedEx packing or double-boxing are recommended. Chauvet reserves the right to use its own discretion to repair or replace returned product(s). Intimidator Scan 110 User Manual Rev. 1 Page 13 of 14... -
Page 16: Contact Us
Outside the U.S., U.K., Ireland, Benelux, France, Germany, or Mexico, contact the dealer of record. Follow the instructions to request support or to return a product. Visit our website for contact details. Page 14 of 14 Intimidator Scan 110 User Manual Rev. 1...